Gibson GA-85 tone stack
Tone stacks and tone controls from amps and pedals, from their schematics, with the stage that drives each one and what it feeds. Turn the knobs and watch the curve. Pin a setting to compare, change any part, and listen through a speaker. Pickups and guitar knobs are on the Guitars page.
The Bass (II) and Volume (II) controls of the Gibson GA-85, with every part as on the bench.
Swipe sideways for the whole drawing. Tap a part to change it. The source drives the end marked in, and the load hangs on the end marked out.
At this setting
0 dB is the source’s voltage with nothing hooked to it, so the curve shows what the stack cuts. A tube source changes the curve only through its output resistance, not its gain.
Pin this curve keeps what the graph shows, up to three pins in their own colors. Pins stay when you switch stacks, so you can lay a Marshall treble sweep over a Vox one. In a sweep, the lightest line is the knob at 0 and the darkest is 10.
Listen
You hear a picked string through a guitar on full, with 15 feet of cable. Play without it leaves the stack out.
Source and load
Driven by
Driving
The knobs
- Bass (II)
- Channel II bass, the same as channel I’s. Turned up, more of the lows get through. The drawing marks no taper, so reverse audio is assumed.
- Volume (II)
- Channel II volume, 2 MΩ linear, wired like channel I’s but with no cap across it.
Parts
- 50 nF
- Coupling cap into the tone network.
- 150 kΩ
- Into the bass path, as on channel I.
- 10 nF
- The bass path’s cap to ground.
- Bass 1.8M
- 1.8 MΩ, Channel II bass, the same as channel I’s. Turned up, more of the lows get through. The drawing marks no taper, so reverse audio is assumed.
- 200 kΩ
- The end of the bass path.
- 330 pF
- Straight across the bass path, .00033 µF. Channel II has no treble pot, so the highs always get through this way.
- Vol 2M
- 2 MΩ, Channel II volume, 2 MΩ linear, wired like channel I’s but with no cap across it.
- 100 kΩ
- Mixing resistor from channel II to the driver’s grid.
Source and load
Source: 80 kΩ, the output resistance of the stage before it on the bench at 1 kHz. Load: 480 kΩ with 67 pF across it, the input of what follows it on the bench, from its impedance at 1 and 10 kHz.
Values, wiring and drawing are taken from the Gibson GA-85 on the bench, so the two always match.
Warnings. The summary above the graph turns red if the stack can’t be solved as set, usually from a part at zero or a shorted pot track.
How this tool works. We solve each stack with the circuit bench’s engine: the source stage’s operating point first, then every part at 161 frequencies from 20 Hz to 20 kHz. A stack that’s also in a bench circuit is built from that circuit file, so the two always match.
The curves are small-signal. They don’t show clipping or grid current in the next stage. For the stage before or after a stack, try the gain stage tool.
Spot an error, or want a circuit added? Email info@swellamps.com. A schematic or a clear photo of one helps. Anything you send may be used to improve these models and our desktop app.
© 2026 Swell Amplification LLC. All rights reserved. The simulator and tools, their circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.