Fender 6G9 Tremolux tone stack
Tone stacks and tone controls from amps and pedals, from their schematics, with the stage that drives each one and what it feeds. Turn the knobs and watch the curve. Pin a setting to compare, change any part, and listen through a speaker. Pickups and guitar knobs are on the Guitars page.
The Bass and Treble controls of the Fender 6G9 Tremolux, with every part as on the bench. The Fender 6G5-A Pro (vibrato channel), Fender 6G8-A Twin (vibrato channel), and Fender 6G14-A Showman (vibrato channel) have the same network.
Swipe sideways for the whole drawing. Tap a part to change it. The source drives the end marked in, and the load hangs on the end marked out.
At this setting
0 dB is the source’s voltage with nothing hooked to it, so the curve shows what the stack cuts. A tube source changes the curve only through its output resistance, not its gain.
Pin this curve keeps what the graph shows, up to three pins in their own colors. Pins stay when you switch stacks, so you can lay a Marshall treble sweep over a Vox one. In a sweep, the lightest line is the knob at 0 and the darkest is 10.
Listen
You hear a picked string through a guitar on full, with 15 feet of cable. Play without it leaves the stack out.
Source and load
Driven by
Driving
The knobs
- Bass
- Bass, 250 kΩ audio, a variable resistor from the treble pot’s tap to the bass cap. Turned down, it ties the tap to the 6800 Ω through the bass cap and the lows drain away.
- Treble
- Treble, 350 kΩ audio, tapped 70 kΩ from its bottom lug. The highs reach the top and the lows the tap, and the wiper mixes the two. Below the tap the wiper slides toward the .003 µF and the highs drop away.
Parts
- 250 pF
- Treble cap, 250 pF, from the plate to the top of the treble pot. No coupling cap comes first: every path from the plate to ground goes through a cap.
- 100 kΩ
- From the plate down to the two caps below. The lows and mids go this way.
- 100 nF
- Carries the lows and mids on to the treble pot’s tap.
- 50 nF
- Bass cap, to the bottom of the bass pot and the 6800 Ω.
- Bass
- 250 kΩ, Bass, 250 kΩ audio, a variable resistor from the treble pot’s tap to the bass cap. Turned down, it ties the tap to the 6800 Ω through the bass cap and the lows drain away.
- 6.8 kΩ
- From the bottom of the bass pot to ground.
- Treble
- 350 kΩ, Treble, 350 kΩ audio, tapped 70 kΩ from its bottom lug. The highs reach the top and the lows the tap, and the wiper mixes the two. Below the tap the wiper slides toward the .003 µF and the highs drop away.
- 3 nF
- From the treble pot’s bottom lug to ground. With the wiper below the tap it cuts the highs.
Source and load
Source: 40 kΩ, the output resistance of the stage before it on the bench at 1 kHz. Load: 1 MΩ with 37 pF across it, the input of what follows it on the bench, from its impedance at 1 and 10 kHz.
Values, wiring and drawing are taken from the Fender 6G9 Tremolux on the bench, so the two always match.
Warnings. The summary above the graph turns red if the stack can’t be solved as set, usually from a part at zero or a shorted pot track.
How this tool works. We solve each stack with the circuit bench’s engine: the source stage’s operating point first, then every part at 161 frequencies from 20 Hz to 20 kHz. A stack that’s also in a bench circuit is built from that circuit file, so the two always match.
The curves are small-signal. They don’t show clipping or grid current in the next stage. For the stage before or after a stack, try the gain stage tool.
Spot an error, or want a circuit added? Email info@swellamps.com. A schematic or a clear photo of one helps. Anything you send may be used to improve these models and our desktop app.
© 2026 Swell Amplification LLC. All rights reserved. The simulator and tools, their circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.