Dumble Overdrive Special #183 tone stack

Tone stacks and tone controls from amps and pedals, from their schematics, with the stage that drives each one and what it feeds. Turn the knobs and watch the curve. Pin a setting to compare, change any part, and listen through a speaker. Pickups and guitar knobs are on the Guitars page.

Stack and the source and load

The Middle, Treble, and Bass controls of the Dumble Overdrive Special #183, with every part as on the bench.

Swipe sideways for the whole drawing. Tap a part to change it. The source drives the end marked in, and the load hangs on the end marked out.

At this setting

Frequency response

Every tone setting Part tolerance

0 dB is the source’s voltage with nothing hooked to it, so the curve shows what the stack cuts. A tube source changes the curve only through its output resistance, not its gain.

Pin this curve keeps what the graph shows, up to three pins in their own colors. Pins stay when you switch stacks, so you can lay a Marshall treble sweep over a Vox one. In a sweep, the lightest line is the knob at 0 and the darkest is 10.

Listen

Note Chord

Guitar

Match loudness Speaker

You hear a picked string through a guitar on full, with 15 feet of cable. Play without it leaves the stack out.

Source and load

Driven by

Driving

The knobs

Middle: Middle, 250 kΩ linear as a variable resistor to ground. Turned up, its resistance rises and less of the mids go to ground.
Treble: Treble, 270 kΩ audio on the drawing. Its wiper is the stack’s output, the top of Volume.
Bass: Bass, 312 kΩ linear on the drawing. Its top connects to the bass cap and its wiper feeds Treble’s bottom on Rock. Turned up, the wiper moves toward the bass cap.

Parts

2 nF: First treble cap, .002 µF, from V1a’s plate. With the 390 pF after it the two make about 330 pF.
4.7 MΩ: From the two treble caps’ junction to ground. It keeps the junction at 0 V DC, so the Mid boost switch doesn’t pop.
390 pF: Second treble cap, 390 pF ceramic, to the top of Treble. The Mid boost switch shorts it.
150 kΩ: Slope resistor, from V1a’s plate to the bass and middle caps.
100 nF: Bass cap, to the top of Bass.
10 nF: Middle cap, to Middle.
Middle: 250 kΩ, Middle, 250 kΩ linear as a variable resistor to ground. Turned up, its resistance rises and less of the mids go to ground.
Treble: 270 kΩ, Treble, 270 kΩ audio on the drawing. Its wiper is the stack’s output, the top of Volume.
Bass: 312 kΩ, Bass, 312 kΩ linear on the drawing. Its top connects to the bass cap and its wiper feeds Treble’s bottom on Rock. Turned up, the wiper moves toward the bass cap.
10 kΩ: Under Bass, to ground.
1 nF: On Rock, from the wiper side of Bass to its bottom, .001 µF 600 V. It lets the treble around the part of Bass below the wiper.
22 MΩ: Across the PAB relay’s first contact, from Treble’s bottom to the Rock/Jazz switch. It keeps the open contact at the same DC level, so the relay doesn’t pop.
22 MΩ: Across the PAB relay’s second contact, from Bass’s wiper to the Rock/Jazz switch, the same.

Source and load

Source: 62 kΩ, the output resistance of the stage before it on the bench at 1 kHz. Load: 890 kΩ with 92 pF across it, the input of what follows it on the bench, from its impedance at 1 and 10 kHz.

Values, wiring and drawing are taken from the Dumble Overdrive Special #183 on the bench, so the two always match.

Warnings. The summary above the graph turns red if the stack can’t be solved as set, usually from a part at zero or a shorted pot track.

How this tool works. We solve each stack with the circuit bench’s engine: the source stage’s operating point first, then every part at 161 frequencies from 20 Hz to 20 kHz. A stack that’s also in a bench circuit is built from that circuit file, so the two always match.

The curves are small-signal. They don’t show clipping or grid current in the next stage. For the stage before or after a stack, try the gain stage tool.

Spot an error, or want a circuit added? Email info@swellamps.com. A schematic or a clear photo of one helps. Anything you send may be used to improve these models and our desktop app.

© 2026 Swell Amplification LLC. All rights reserved. The simulator and tools, their circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.

Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.

From Swell Amplification, swellamps.com.