Gibson GA-60 Hercules tone stack
Tone stacks and tone controls from amps and pedals, from their schematics, with the stage that drives each one and what it feeds. Turn the knobs and watch the curve. Pin a setting to compare, change any part, and listen through a speaker. Pickups and guitar knobs are on the Guitars page.
The Treble and Bass controls of the Gibson GA-60 Hercules, with every part as on the bench.
Swipe sideways for the whole drawing. Tap a part to change it. The source drives the end marked in, and the load hangs on the end marked out.
At this setting
0 dB is the source’s voltage with nothing hooked to it, so the curve shows what the stack cuts. A tube source changes the curve only through its output resistance, not its gain.
Pin this curve keeps what the graph shows, up to three pins in their own colors. Pins stay when you switch stacks, so you can lay a Marshall treble sweep over a Vox one. In a sweep, the lightest line is the knob at 0 and the darkest is 10.
Listen
You hear a picked string through a guitar on full, with 15 feet of cable. Play without it leaves the stack out.
Source and load
Driven by
Driving
The knobs
- Treble
- Treble, 2 MΩ audio, its wiper on the top of the volume. Clockwise the wiper moves toward the 500 pF and adds treble. Counterclockwise it moves toward the .005 µF to ground and cuts treble. The drawing doesn’t mark which way it turns.
- Bass
- Bass, 2 MΩ linear, across the 500 pF as a variable resistor. Its resistance falls as it’s turned up, so more of the bass gets around the cap. The drawing doesn’t mark which way it turns.
Parts
- 22 nF
- Coupling cap to the tone network.
- 500 pF
- Treble cap, 500 pF, to the bright end of the Treble pot. It passes only the treble.
- Treble 2M
- 2 MΩ, Treble, 2 MΩ audio, its wiper on the top of the volume. Clockwise the wiper moves toward the 500 pF and adds treble. Counterclockwise it moves toward the .005 µF to ground and cuts treble. The drawing doesn’t mark which way it turns.
- 5 nF
- .005 µF from the Treble pot’s dark end to ground. On the amp the limiter’s light-dependent resistor sits here too. It’s left out.
- 500 pF
- The bass path’s 500 pF. By itself it passes only treble.
- Bass 2M
- 2 MΩ, Bass, 2 MΩ linear, across the 500 pF as a variable resistor. Its resistance falls as it’s turned up, so more of the bass gets around the cap. The drawing doesn’t mark which way it turns.
- 100 kΩ
- 100 kΩ from the bass path to the top of the volume.
Source and load
Source: 73 kΩ, the output resistance of the stage before it on the bench at 1 kHz. Load: 1 MΩ, the input of what follows it on the bench, from its impedance at 1 and 10 kHz.
Values, wiring and drawing are taken from the Gibson GA-60 Hercules on the bench, so the two always match.
How a tone stack works
Two ways through In the FMV stack the treble cap is small, so it passes only the highs, straight to the top of the treble pot. Everything else goes through the slope resistor, then the bass and mid caps. The bass cap feeds the bottom of the treble pot, and the bass pot sits between there and the top of the mid pot. Turned down, it shorts the bass cap’s end toward the mid pot, and the lows drop away. The mid pot sits between the mid cap and ground, so turning it up lifts the whole lower path off ground. The output is the treble pot’s wiper, a mix of the highs at the top of its track and the lows and mids at the bottom.
The mid scoop Where a stack passes the bass and the treble by different paths, there’s a stretch in between where neither path passes much. That dip in the mids is the scoop. Its depth and center move with the knobs. In the FMV stack the slope resistor and treble cap set where it sits, and the mid knob fills it in. A plain low-pass or high-pass filter has no scoop.
Warnings The summary above the graph turns red if the stack can’t be solved as set, usually from a part at zero or a shorted pot track.