Gibson Titan tone stack
Tone stacks and tone controls from amps and pedals, from their schematics, with the stage that drives each one and what it feeds. Turn the knobs and watch the curve. Pin a setting to compare, change any part, and listen through a speaker. Pickups and guitar knobs are on the Guitars page.
The Mid I control of the Gibson Titan, with every part as on the bench.
Swipe sideways for the whole drawing. Tap a part to change it. The source drives the end marked in, and the load hangs on the end marked out.
At this setting
0 dB is the source’s voltage with nothing hooked to it, so the curve shows what the stack cuts. A tube source changes the curve only through its output resistance, not its gain.
Pin this curve keeps what the graph shows, up to three pins in their own colors. Pins stay when you switch stacks, so you can lay a Marshall treble sweep over a Vox one. In a sweep, the lightest line is the knob at 0 and the darkest is 10.
Listen
You hear a picked string through a guitar on full, with 15 feet of cable. Play without it leaves the stack out.
Source and load
Driven by
Driving
The knobs
- Mid I
- Mid Range I, 50 kΩ audio, from ground to the bottom of R9. Its wiper takes C5. Toward ground, C5 bleeds the middle of the range to ground and the mids drop. Toward R9, C5 and R9 lead the signal back to V2A’s grid.
Parts
- 390 kΩ
- First of the two resistors from Loudness I to V2A’s grid.
- 100 kΩ
- Second resistor to V2A’s grid.
- 15 nF
- From between R7 and R8 to the Mid Range pot’s wiper.
- Mid 50k
- 50 kΩ, Mid Range I, 50 kΩ audio, from ground to the bottom of R9. Its wiper takes C5. Toward ground, C5 bleeds the middle of the range to ground and the mids drop. Toward R9, C5 and R9 lead the signal back to V2A’s grid.
- 470 kΩ
- From V2A’s grid to the top of the Mid Range pot. It’s the grid’s path to ground.
- 250 pF
- Across R7 and R8, so the treble goes straight to V2A’s grid.
Source and load
Source: 17 kΩ, the output resistance of the stage before it on the bench at 1 kHz. Load: the next grid, with no grid resistor of its own. The pots are its path to ground, so only its input capacitance counts, 21 pF as measured on the bench.
Values, wiring and drawing are taken from the Gibson Titan on the bench, so the two always match.
How a tone stack works
Two ways through In the FMV stack the treble cap is small, so it passes only the highs, straight to the top of the treble pot. Everything else goes through the slope resistor, then the bass and mid caps. The bass cap feeds the bottom of the treble pot, and the bass pot sits between there and the top of the mid pot. Turned down, it shorts the bass cap’s end toward the mid pot, and the lows drop away. The mid pot sits between the mid cap and ground, so turning it up lifts the whole lower path off ground. The output is the treble pot’s wiper, a mix of the highs at the top of its track and the lows and mids at the bottom.
The mid scoop Where a stack passes the bass and the treble by different paths, there’s a stretch in between where neither path passes much. That dip in the mids is the scoop. Its depth and center move with the knobs. In the FMV stack the slope resistor and treble cap set where it sits, and the mid knob fills it in. A plain low-pass or high-pass filter has no scoop.
Warnings The summary above the graph turns red if the stack can’t be solved as set, usually from a part at zero or a shorted pot track.