Two-channel piggyback with four 6L6GCs and optical tremolo, 1963 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Gibson Titan (I, III, V).
Two channels, each with Bass, Loudness, Mid Range and Treble, mixed into a 12AU7 cathodyne, a 6FQ7 driver pair and four 6L6GCs in fixed bias. The tremolo lights a lamp beside a light-dependent resistor on channel I.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Channel I runs through three triode stages and channel II through two, and the two meet through 100 kΩ each. Bass is a variable resistor in series with the signal, with a small cap across it. Turned down, its resistance goes up and mostly the treble gets past the cap. Each Treble pot sits under the next stage’s grid, with a small cap from that stage’s plate to its wiper. Turned down, the wiper moves toward the grid and the cap feeds the plate’s swing back to the grid, which cuts the treble. The tremolo’s oscillator lights a lamp through a lamp driver, and the lamp’s glow lowers a light-dependent resistor from channel I’s Loudness wiper to ground, so only channel I throbs. The power amp is a cathodyne into a pair of 6FQ7 drivers, into four 6L6GCs with no feedback.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R2, 68 kΩ
- Channel I’s input 1 resistor into the grid. With nothing plugged into input 2, this resistor and input 2’s resistor are in parallel, so a guitar in input 1 goes through 34 kΩ to the grid. That is enough to stop radio pickup and too little to cut treble.
- R3, 68 kΩ
- Channel I’s input 2 resistor into the grid. With nothing plugged into input 1, input 1’s tip is grounded, and the two 68 kΩ resistors form a divider. Input 2 is about 6 dB quieter and loads the guitar with 136 kΩ.
- R1, 1 MΩ
- Input 1’s 1 MΩ to ground. It sets the load a guitar in input 1 sees, and with a patch lead in input 1 it is the end of the lead’s path.
- R18, 68 kΩ
- Channel II’s input 1 resistor into the grid. With nothing plugged into input 2, this resistor and input 2’s resistor are in parallel, so a guitar in input 1 goes through 34 kΩ to the grid. That is enough to stop radio pickup and too little to cut treble.
- R19, 68 kΩ
- Channel II’s input 2 resistor into the grid. With nothing plugged into input 1, input 1’s tip is grounded, and the two 68 kΩ resistors form a divider. Input 2 is about 6 dB quieter and loads the guitar with 136 kΩ.
- R17, 1 MΩ
- Input 1’s 1 MΩ to ground. It sets the load a guitar in input 1 sees, and with a patch lead in input 1 it is the end of the lead’s path.
- V1, 6EU7
- Both halves of a 6EU7 in parallel, channel I’s input stage. Two halves side by side have twice the current and half the plate resistance of one, and lower noise.
- 47k, 47 kΩ
- Plate resistor for V1. The drawing reads +186 V on the plate.
- 680, 680 Ω
- Cathode resistor for V1, +1.27 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V1’s cathode resistor.
- .047µ, 47 nF
- Coupling cap from V1 to the Bass control.
- Bass 2M, 2 MΩ pot, reverse audio taper
- Bass I, 2 MΩ reverse audio, a variable resistor in series with the signal. Turned up, its resistance drops toward 0 and the whole range gets through. Turned down, it rises to 2 MΩ and mostly the treble gets past C3.
- 33k, 33 kΩ
- In series with the Bass pot, so the path never drops below 33 kΩ.
- .0033µ, 3.3 nF
- Across the Bass pot and R6. The treble always gets through here, whatever Bass is set to.
- Loud 250k, 250 kΩ pot, audio taper
- Loudness I, 250 kΩ audio, channel I’s volume. Its wiper feeds the tone network, and the tremolo’s LDR hangs from it.
- Lamp, 24 V bulb, 18 mA
- The lamp in the tremolo’s lamp and cell, from the 150 V line to the lamp driver’s plate. The drawing reads 8 V across it at idle. The bench uses the Gibson LDR-500’s bulb, since the drawing’s RE-LDR-430G has no figures here.
- LDR, Gibson LDR-500 cell
- The light-dependent resistor, from Loudness I’s wiper to ground. Lit, its resistance drops and it pulls channel I down. Dark, it’s about 1 MΩ and hardly loads the wiper. The bench uses the Gibson LDR-500 cell’s figures.
- 390k, 390 kΩ
- First of the two resistors from Loudness I to V2A’s grid.
- 100k, 100 kΩ
- Second resistor to V2A’s grid.
- 250p, 250 pF
- Across R7 and R8, so the treble goes straight to V2A’s grid.
- .015µ, 15 nF
- From between R7 and R8 to the Mid Range pot’s wiper.
- Mid 50k, 50 kΩ pot, audio taper
- Mid Range I, 50 kΩ audio, from ground to the bottom of R9. Its wiper takes C5. Toward ground, C5 bleeds the middle of the range to ground and the mids drop. Toward R9, C5 and R9 lead the signal back to V2A’s grid.
- 470k, 470 kΩ
- From V2A’s grid to the top of the Mid Range pot. It’s the grid’s path to ground.
- V2A, 12AU7 / ECC82
- One half of a 12AU7, channel I’s second stage.
- 100k, 100 kΩ
- Plate resistor for V2A, +114 V on the drawing.
- 3.3k, 3.3 kΩ
- Cathode resistor for V2A, +3.4 V on the drawing.
- .1µ, 100 nF
- Only .1 µF across V2A’s cathode resistor, so the stage has its full gain from about 500 Hz up and less below.
- 100k, 100 kΩ
- With C7, a treble cut after V2A.
- 750p, 750 pF
- From between R12 and R13 to ground. With the 100 kΩ resistors around it, it rolls off the top treble.
- 100k, 100 kΩ
- Second 100 kΩ on the way to V2B.
- .022µ, 22 nF
- Coupling cap to V2B’s grid.
- Treble 500k, 500 kΩ pot, audio taper
- Treble I, 500 kΩ audio, from V2B’s grid to ground, and it’s the grid’s path to ground. C9 from V2B’s plate goes to its wiper. Turned up, the wiper moves toward ground and C9 does little. Turned down, it moves toward the grid, C9 feeds the plate’s swing back and the treble drops. Up is assumed to be brighter.
- 330p, 330 pF
- From V2B’s plate to the Treble pot’s wiper.
- V2B, 12AU7 / ECC82
- The other half of the 12AU7, channel I’s third stage.
- 100k, 100 kΩ
- Plate resistor for V2B, from node B. The drawing reads +124 V on the plate.
- 3.3k, 3.3 kΩ
- Cathode resistor for V2B, +6 V on the drawing.
- .1µ, 100 nF
- Only .1 µF across V2B’s cathode resistor, as on V2A.
- 100k, 100 kΩ
- Channel I’s mixing resistor, from V2B’s plate to the mixing node.
- V7A, 6EU7
- One half of a 6EU7, channel II’s input stage.
- 100k, 100 kΩ
- Plate resistor for V7A, +183 V on the drawing.
- 1.5k, 1.5 kΩ
- Cathode resistor for V7A, +1.32 V on the drawing. It has no number on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V7A’s cathode resistor.
- .01µ, 10 nF
- Coupling cap from V7A to the Bass control.
- Bass 10M, 10 MΩ pot, reverse audio taper
- Bass II, 10 MΩ reverse audio, a variable resistor in series with the signal. Turned up, its resistance drops and the lows get through. Turned down, mostly the treble gets past C13.
- .001µ, 1 nF
- Across the Bass pot, the treble’s way past it.
- Loud 500k, 500 kΩ pot, audio taper
- Loudness II, 500 kΩ audio, channel II’s volume.
- 390k, 390 kΩ
- First of the two resistors from Loudness II to V7B’s grid.
- 100k, 100 kΩ
- Second resistor to V7B’s grid.
- 500p, 500 pF
- Across R22 and R23, the treble’s way to V7B’s grid.
- .015µ, 15 nF
- From between R22 and R23 to the Mid Range pot.
- Mid 50k, 50 kΩ pot, audio taper
- Mid Range II, 50 kΩ audio, a variable resistor from C15 to ground. Turned down, its resistance drops and C15 bleeds the middle of the range away. Turned up, there’s more resistance in the way and the mids come back.
- Treble 1M, 1 MΩ pot, audio taper
- Treble II, 1 MΩ audio, from V7B’s grid to ground, with C16 from V7B’s plate on its wiper. It works as Treble I does. Up is assumed to be brighter.
- 250p, 250 pF
- From V7B’s plate to the Treble pot’s wiper.
- V7B, 6EU7
- The other half of the 6EU7, channel II’s second stage.
- 100k, 100 kΩ
- Plate resistor for V7B, +165 V on the drawing.
- 1.5k, 1.5 kΩ
- Cathode resistor for V7B, not bypassed, +1.22 V on the drawing.
- 100k, 100 kΩ
- Channel II’s mixing resistor. Both plates’ DC meets here too, so the mixing node sits between them, +143 V on the drawing.
- 330p, 330 pF
- From the mixing node to ground. With the two 100 kΩ resistors it cuts the top treble.
- .005µ, 5 nF
- Coupling cap into the cathodyne’s grid.
- 7.5k, 7.5 kΩ
- From node C to the OA2. About 19 mA flows through it, and what the oscillator and lamp driver don’t use flows through the OA2.
- OA2, 150 V
- Stands for V4, an OA2 gas regulator. It holds its line near 150 V whatever current flows. Here it’s a 150 V source with 100 Ω behind it.
- 150k, 150 kΩ
- Plate resistor for the oscillator, from the regulated line. The drawing reads +77 V on the plate.
- V3A, 6EU7
- One half of a 6EU7, the tremolo oscillator. Its cathode is on ground, and its grid sits at −.47 V from grid current through 4.7 MΩ.
- .022µ, 22 nF
- First cap of the oscillator’s phase-shift ladder.
- 330k, 330 kΩ
- First ladder leg to ground.
- .022µ, 22 nF
- Second ladder cap.
- 150k, 150 kΩ
- In series with the Frequency pot, the second leg. It sets the top speed.
- Freq 1.5M, 1.5 MΩ pot, reverse audio taper
- Frequency, 1.5 MΩ reverse audio, as a variable resistor in the second leg. Turned up, its resistance drops and the oscillator runs faster. Its far end goes through the foot switch to ground.
- .01µ, 10 nF
- Third ladder cap, into the grid. At one frequency the ladder turns the plate’s swing upside down by the time it reaches the grid, so the stage oscillates there.
- 4.7M, 4.7 MΩ
- Grid leak for the oscillator, and the ladder’s last leg.
- .022µ, 22 nF
- Couples the oscillator’s swing to the Depth pot and blocks the plate’s DC.
- 1M, 1 MΩ
- With the Depth pot, a divider that brings the oscillator’s swing down to what the lamp driver needs.
- Depth 250k, 250 kΩ pot, audio taper
- Depth, 250 kΩ audio. Its wiper is the lamp driver’s grid. Turned up, more of the oscillator’s swing reaches it and the lamp swings brighter and dimmer.
- V6B, 12AU7 / ECC82
- One half of a 12AU7, the lamp driver. Its plate current runs through the lamp.
- 500, 500 Ω pot, linear taper
- R65, a 500 Ω wirewound pot on the lamp driver’s cathode, set at the factory. It sets the lamp’s idle current. The drawing shows no setting, so it’s set at half its turn, which puts the cathode near the drawing’s 2.7 V.
- V6A, 12AU7 / ECC82
- 12AU7 (ECC82), a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 100k, 100 kΩ
- The cathodyne’s plate resistor, the output to tube B.
- 3.3k, 3.3 kΩ
- The cathodyne’s bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 100k, 100 kΩ
- The cathodyne’s cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470 kΩ
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathode’s high DC voltage. It’s the grid’s only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ω.
- .02µ, 20 nF
- Coupling cap from the inverter to side A’s driver.
- .02µ, 20 nF
- Coupling cap from the inverter to side B’s driver.
- 680, 680 Ω
- The drivers’ cathode resistor, 680 Ω to ground for both halves, with no bypass cap. The two cathodes share it, so the pair works somewhat like a long-tail pair: what one half gains in current the other loses, which evens out the two sides’ swings.
- 220k, 220 kΩ
- Grid leak for side A’s driver, to ground.
- V5, 6CG7
- 6CG7, side A’s driver: a gain stage that raises the inverter’s signal about 14 times on its way to tube A’s grids. The other half drives side B, and the two share one cathode resistor.
- 47k, 47 kΩ
- The driver’s plate resistor, 47k Ω from the node for the drivers and the regulator.
- .1µ, 100 nF
- Coupling cap from the driver’s plate to tube A’s grids.
- 220k, 220 kΩ
- Grid leak for side B’s driver, to ground.
- V5, 6CG7
- The other half of the 6CG7, side B’s driver.
- 47k, 47 kΩ
- The driver’s plate resistor, 47k Ω from the node for the drivers and the regulator.
- .1µ, 100 nF
- Coupling cap from the driver’s plate to tube B’s grids.
- 500, 500 Ω
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current. Each of the two tubes has its own 1k. The resistors are drawn as one part, the two in parallel.
- 500, 500 Ω
- Grid stopper for tube B. Each of the two tubes has its own 1k. The resistors are drawn as one part, the two in parallel.
- V9, V11, 6L6GC
- 6L6GC, tube A of the push-pull pair, cathode grounded, biased from the fixed bias supply. Two tubes in parallel, drawn as one.
- V10, V12, 6L6GC
- 6L6GC, tube B of the pair. Two tubes in parallel, drawn as one.
- 47k, 47 kΩ
- Grid leak for tube A, returned to the bias supply. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 47k, 47 kΩ
- Grid leak for tube B.
- 235, 235 Ω
- Screen resistor for tube A. It limits the screen current when the tube is driven hard. Each of the two tubes has its own 470. The resistors are drawn as one part, the two in parallel.
- 235, 235 Ω
- Screen resistor for tube B. Each of the two tubes has its own 470. The resistors are drawn as one part, the two in parallel.
- 4 H, 4 H
- The choke from the reservoir cap to B+, as on the amp’s drawing. The output transformer’s center tap, the screens and everything after them hang past it, so all of their current runs through it. It passes DC with little drop. With the cap after it, it would filter ripple, but ripple isn’t modeled here. Typical of the part.
- 50, 50 Ω
- The choke’s winding resistance, typical. With the output tubes’ whole current through it, it’s most of the DC drop between the reservoir and B+.
- 40µ, 40 µF electrolytic
- Filter cap on B+ after the choke, where the output transformer’s center tap and the screens hang.
- 4k, 4 kΩ
- Dropping resistor from the screen supply node to the node for the drivers and the regulator, as on the Gibson Titan drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20µ, 20 µF electrolytic
- Filter cap at the node for the drivers and the regulator. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 2.2k, 2.2 kΩ
- Dropping resistor from the node for the drivers and the regulator to the node for the inverter and V2B, as on the Gibson Titan drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20µ, 20 µF electrolytic
- Filter cap at the node for the inverter and V2B. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 2.2k, 2.2 kΩ
- Dropping resistor from the node for the inverter and V2B to the node for the preamp, as on the Gibson Titan drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 20µ, 20 µF electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 2 kΩ to 8 Ω, 20 H primary, 5 mH leakage
- The output transformer, 2 kΩ plate to plate into 8 Ω, center tap on B+ after the choke. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 339 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 339 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 339 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 20 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 20 Ω
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 40µ, 40 µF electrolytic
- The reservoir cap. It feeds the choke, and past it the output transformer’s center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Bias tap, 50 V ac, 60 Hz
- The power transformer’s bias tap, 50 V ac, as a sine source at the mains frequency. Typical of the part.
- tap R, 100 Ω
- The bias tap’s own resistance, 100 Ω, typical. The drawing has no resistor between the tap and the diode.
- Bias diode, 1N4001
- The bias rectifier, a silicon diode turned so the supply comes out negative.
- 10µ, 10 µF electrolytic
- Filter cap on the bias supply, its plus side to ground.
- 10k, 10 kΩ
- Second resistor of the bias supply, 10k Ω to the bias line. With the cap after it, it filters the ripple a second time.
- 10µ, 10 µF electrolytic
- Second filter cap, on the bias line, its plus side to ground.
- 22k, 22 kΩ
- From the bias line to ground, 22k Ω. With the 10k Ω above it, it divides the supply down to the bias. There’s no bias pot, so change this resistor to change the bias. Bigger runs the tubes colder.
- Coil R, 8.69 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 8 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 464 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 2.19 Ω
- Limits what Loss L2 adds.
- Tank R, 83.7 Ω
- Height of the bass resonance, about 92 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 21.1 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The Titan I, III and V, as on the factory drawing. They differ only in their speakers.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.