Ten-stage photocell phaser, 1974 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the MXR Phase 100.
Ten op-amp stages turn the guitar’s phase, and six of them are set by light cells. Mixed back with the dry signal, the two cancel at five notches. A slow oscillator brightens and dims three LEDs, and the notches sweep. A four-way Intensity switch sets the sweep’s width and turns regeneration on or off.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC4a raises the guitar 1.5 times and feeds ten all-pass stages. Each one passes every pitch at the same level and turns its phase, 90° at 1 / (2π R C) with C the stage’s .01 µF. Stages 1, 2, 9 and 10 have 20 kΩ and stay at about 800 Hz. Stages 3 to 8 have a light cell, so their 90° point moves with the LEDs. R18 and R19 mix the dry and wet signals equally. Where the wet signal has turned 180°, 540°, 900° and so on, the two cancel, so ten stages make five notches. With the LFO at its middle in position 1 they sit at about 75, 250 and 510 Hz, 1 kHz and 3.3 kHz, and between them the output is about 3 dB over the input. The LFO’s ramp moves the base of a Darlington that runs the three LEDs in series. Its current grows about ten times for each 0.12 V on its base, so the cells’ resistance moves evenly in pitch. Speed runs from one sweep every 10.5 seconds to about 4 a second. Intensity 1 is a narrow sweep, 2 the narrow sweep with regeneration, 3 the full sweep and 4 the full sweep with regeneration. The cells are typical of a VTL5C module and the trim is set at its middle, both assumed, so a real pedal’s sweep may sit elsewhere.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C14, 15 µF electrolytic
- Across the 9 V supply.
- D1, 1N914 / 1N4148
- Reverse-polarity protection, doing nothing in normal use.
- R39, 10 kΩ
- With R40, splits the 9 V in half for Vref.
- R40, 10 kΩ
- The bottom of the Vref divider.
- C17, 15 µF electrolytic
- Vref’s filter cap. It makes Vref a quiet AC ground for the stages.
- R2, 10 kΩ
- Input series resistor.
- C1, 10 nF
- Input coupling cap. Against R12 it cuts below about 34 Hz.
- R12, 470 kΩ
- Biases the input buffer at Vref and sets most of the input impedance.
- IC4a, TL022
- The input buffer. With R3 and R13 its gain is 1.5. It drives the first stage and the dry side of the mix.
- R13, 20 kΩ
- From the minus input to Vref. With R3 it sets the buffer’s gain, 1 + 10 k / 20 k = 1.5.
- R3, 10 kΩ
- The buffer’s feedback.
- C2, 300 pF
- Across R3. It rolls the buffer’s extra gain off above about 53 kHz.
- R4, 10 kΩ
- Into the minus input. With the 10 kΩ feedback resistor it makes the inverting half of the stage, a gain of one, inverted.
- R5, 10 kΩ
- Feedback, equal to the input resistor, so every pitch comes out at the same level and only the phase moves.
- C3, 10 nF
- Feeds the plus input. With the 20 kΩ it sets where this stage turns the phase 90°, about 800 Hz. Low notes come out inverted, high notes as they went in.
- R14, 20 kΩ
- From the plus input to Vref. This stage has no light cell, so its 90° point stays at about 800 Hz. Stages 1, 2, 9 and 10 are fixed this way.
- IC5B, TL022
- Half a TL022, the first of ten phase-shift stages.
- R6, 10 kΩ
- Into the minus input, as in the first stage.
- R7, 10 kΩ
- Feedback, equal to the input resistor.
- C4, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R15, 20 kΩ
- From the plus input to Vref, 20 kΩ. This stage doesn’t sweep.
- IC6A, TL022
- Half a TL022, phase-shift stage 2.
- R8, 10 kΩ
- Into the minus input, as in the first stage.
- R9, 10 kΩ
- Feedback, equal to the input resistor.
- C5, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R16, 100 kΩ
- Beside the light cell, from the plus input to Vref. With the cell dark it sets the lowest 90° point, about 160 Hz.
- IC6B, TL022
- Half a TL022, phase-shift stage 3.
- VR3A, VTL5C-type cell
- One of the two cells in VR3, from the plus input to Vref. Lit harder, its resistance falls and the stage turns at a higher pitch. Its figures are typical of a VTL5C-type cell and assumed.
- R10, 10 kΩ
- Into the minus input, as in the first stage.
- R11, 10 kΩ
- Feedback, equal to the input resistor.
- C6, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R17, 100 kΩ
- Beside this stage’s cell, 100 kΩ.
- IC5A, TL022
- Half a TL022, phase-shift stage 4.
- VR3B, VTL5C-type cell
- A cell in VR3, lit by that module’s LED.
- R31, 10 kΩ
- Into the minus input, as in the first stage.
- R30, 10 kΩ
- Feedback, equal to the input resistor.
- C13, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R38, 100 kΩ
- From the previous stage’s output to Vref, on the input side of C13, where the drawing puts it. So this stage’s cell is alone on the plus input, and with the LED low this stage turns lower than its neighbors.
- IC4B, TL022
- Half a TL022, phase-shift stage 5.
- VR2B, VTL5C-type cell
- A cell in VR2, lit by that module’s LED.
- R29, 10 kΩ
- Into the minus input, as in the first stage.
- R28, 10 kΩ
- Feedback, equal to the input resistor.
- C12, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R37, 100 kΩ
- Beside this stage’s cell, 100 kΩ.
- IC3A, TL022
- Half a TL022, phase-shift stage 6.
- VR2A, VTL5C-type cell
- A cell in VR2, lit by that module’s LED.
- R27, 10 kΩ
- Into the minus input, as in the first stage.
- R26, 10 kΩ
- Feedback, equal to the input resistor.
- C11, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R36, 100 kΩ
- From the previous stage’s output to Vref, on the input side of C11, where the drawing puts it. So this stage’s cell is alone on the plus input, and with the LED low this stage turns lower than its neighbors.
- IC2B, TL022
- Half a TL022, phase-shift stage 7.
- VR1B, VTL5C-type cell
- A cell in VR1, lit by that module’s LED.
- R25, 10 kΩ
- Into the minus input, as in the first stage.
- R24, 10 kΩ
- Feedback, equal to the input resistor.
- C10, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R35, 100 kΩ
- Beside this stage’s cell, 100 kΩ.
- IC1A, TL022
- Half a TL022, phase-shift stage 8.
- VR1A, VTL5C-type cell
- A cell in VR1, lit by that module’s LED.
- R23, 10 kΩ
- Into the minus input, as in the first stage.
- R22, 10 kΩ
- Feedback, equal to the input resistor.
- C9, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R34, 20 kΩ
- From the plus input to Vref, 20 kΩ. This stage doesn’t sweep.
- IC2A, TL022
- Half a TL022, the ninth stage. Its output also feeds the regeneration.
- R21, 10 kΩ
- Into the minus input, as in the first stage.
- R20, 10 kΩ
- Feedback, equal to the input resistor.
- C8, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R33, 20 kΩ
- From the plus input to Vref, 20 kΩ. This stage doesn’t sweep.
- IC3B, TL022
- Half a TL022, the tenth stage. Its output is the wet signal.
- R18, 6.2 kΩ
- The dry signal into the mix.
- R19, 6.2 kΩ
- The wet signal into the mix, equal to R18. Where the ten stages have turned the phase 180°, 540°, 900° and so on, the two cancel, and those are the notches.
- C7, 1 µF electrolytic
- Output coupling cap.
- R32, 150 kΩ
- Output pulldown, so the jack sits at 0 V.
- R1, 15 kΩ
- Regeneration. In Intensity 2 and 4 it connects stage 9’s output to stage 3’s minus input, so about two thirds of it comes back around seven stages, and the peaks between the notches ring.
- VR3 LED, Red LED
- VR3’s LED, the first of three in series from 9 V. Its light follows its current, which is the same in all three.
- VR2 LED, Red LED
- VR2’s LED.
- VR1 LED, Red LED
- VR1’s LED. Under it, the Darlington sets the current.
- Q1, 2SC1815
- The Darlington’s output transistor. It carries the LED current.
- Q2, 2SC1815
- Drives Q1’s base. Together they need about 1 V on LB before the LEDs light.
- R54, 20 Ω
- Under Q1’s emitter. Each 0.1 V on LB over the Darlington’s turn-on adds about 5 mA to the LEDs.
- R51, 100 kΩ
- Carries the LFO’s ramp from Q4 to the LED driver.
- R45, 6.2 kΩ
- Holds the driver’s base near Q3’s collector. Against R51 it lets about 6 % of the ramp through.
- R41, 150 kΩ
- From 9 V to the Intensity switch. In positions 1 and 2 the switch joins it to LB.
- R42, 2.4 kΩ
- In positions 1 and 2 it goes beside R45, so less of the ramp reaches LB and the sweep is narrower.
- R43, 56 kΩ
- Q3’s collector load from 9 V.
- Q3, 2SC1815
- Holds its collector at a set voltage, slightly under 1 V, which the trim moves. LB rides on it, so it sets where the sweep sits.
- R46, 47 kΩ
- From Q3’s collector to the top of the trim.
- Center Freq., 20 kΩ pot, linear taper
- The internal Center Freq. trim, 20 kΩ, with its wiper on Q3’s base. Turned up, Q3’s collector rises, the LEDs run brighter and the sweep moves up. Set at its middle, an assumed setting.
- R48, 39 kΩ
- From the bottom of the trim to the divider.
- R49, 120 kΩ
- With R50, a divider at about 0.44 V under the trim.
- R50, 6.2 kΩ
- The bottom of the divider.
- R44, 150 kΩ
- From 9 V to the LFO op-amp’s plus input. With R53 and R55 it sets the two switch points.
- R53, 150 kΩ
- From the plus input to ground.
- R55, 150 kΩ
- Positive feedback from the output. It snaps the op-amp to one side and holds it there until the cap reaches the switch point.
- IC1b, TL022
- The LFO. Its output is a square wave, high or low.
- R52, 150 kΩ
- From the timing cap to the minus input.
- C16, 10 nF
- From the minus input to the output. With R52 it makes each flip slightly late, so at top speed the cap swings beyond the switch points.
- R56, 10 kΩ
- In series with Speed. It sets the top speed.
- Speed, 500 kΩ pot, reverse audio taper
- Speed, 500 kΩ, a variable resistor from R56 to the timing cap. At 0 all of it is in the path, the slowest setting, and at full none of it is. The drawing marks it log. It’s modeled as reverse audio, an assumption, so the speed spreads evenly over the turn.
- C15, 15 µF electrolytic
- The timing cap. It ramps up and down between the switch points, and that ramp is the sweep.
- Q4, 2SC1815
- An emitter follower, so R51 doesn’t load the timing cap.
About this version
- Script logo, TL022
- The circuit as redrawn from an early unit. TL022 op-amps, VTL5C-type light cells with red LEDs, 2SC1815 transistors in place of the 2SC1849.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.