Six-stage photocell phaser, 1977 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Mu-Tron Phasor II.
Six all-pass stages, which pass every pitch at the same level and only turn its phase, are each set by a photocell, and one LED lights all six. A triangle LFO drives the LED, and Feedback sends part of the phased signal back to the input. The knobs are Rate, Depth and Feedback.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC1A inverts the guitar and sends it through six all-pass stages. Each one keeps the level and turns the phase, 90Β° at 1 / (2Ο R C), where R is the stageβs cell in parallel with its 220 kΞ© and C is 6.8 nF. Six of them turn the phase 1,080Β°. IC6A subtracts the phased signal from the dry, so where the two are in step they cancel. That is three notches, with peaks between them. With the LED dark the cells sit near 220 kΞ© and the stages turn at about 106 Hz. With the LED near 10 mA the cells drop to about 1 kΞ©, and the stages turn at about 23 kHz. The LFO is a triangle, 0.095 to 20 sweeps a second on Rate. Depth sets how much of it reaches the LED driver, and the Offset trim sets where the LED rests. The driver turns the sweep into LED current, rising faster near the top. Feedback sends up to 0.73 of the phaserβs output back into IC1A, so the peaks between the notches ring. The cellsβ figures are typical of a VTL5C-type cell and assumed. The supply is a steady Β±12 V, as the originalβs mains supply made.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- β12 V, -12 V
- The β12 V rail. The original made it from the mains, modeled as a steady source.
- C1, 47βnF
- Input coupling cap. With R1 it cuts below about 9 Hz.
- R1, 390βkΞ©
- Holds the input at ground. It is most of the input impedance.
- R2, 3.9βkΞ©
- With C2, keeps radio frequencies out of IC1B.
- C2, 33βpF
- With R2, a low-pass far above the audio band.
- IC1B, RC4558
- Half a 4558, a follower. Its output is the dry signal.
- R3, 390βkΞ©
- Feedback from IC1Bβs output to its minus input. With nothing from the minus input to ground, the gain stays 1.
- C3, 100βnF
- Across R3.
- R4, 4.7βkΞ©
- Into IC1Aβs minus input from the dry signal.
- R5, 4.7βkΞ©
- IC1Aβs feedback, equal to R4, so the dry signal goes into the phaser inverted at the same level.
- C4, 1βnF
- Across R5. It rolls IC1A off above about 34 kHz.
- IC1A, RC4558
- Half a 4558. It inverts the dry signal and adds the feedback from its plus input, at a gain of 2.
- R6, 4.7βkΞ©
- With R7, a divider on the feedback. IC1Aβs gain of 2 makes up for part of it, so at full Feedback 0.73 of the phaserβs output comes back.
- C5, 3.3βnF
- Across R6. It trims the feedback above about 16 kHz.
- R7, 8.2βkΞ©
- From the Feedback wiper to IC1Aβs plus input.
- Feedback, 10βkΞ© pot, audio taper
- Feedback, 10 kΞ© audio, across the phaserβs output. Its wiper sends part of the phased signal back into IC1A. Turned up, the peaks between the notches ring and the notches get shallower.
- R8, 4.7βkΞ©
- Into the minus input. Equal to the feedback resistor, so every pitch comes out at the same level and only the phase moves.
- R9, 4.7βkΞ©
- Feedback, equal to the input resistor.
- C6, 6.8βnF
- From the stageβs input to the plus input. With the cell and its 220 kΞ© it sets the pitch where this stage turns the phase 90Β°, which is 1 / (2Ο R C). Lows come out inverted, highs come out as they went in.
- R10, 220βkΞ©
- Across the cell. It sets the most resistance the stage can have, so with the LED dark this stage turns at about 106 Hz.
- LDR1, VTL5C-type cell
- One of the six photocells around the LED D3. Lit harder, its resistance falls and the stage turns at a higher pitch. Its figures are typical of a VTL5C-type cell and assumed.
- IC2B, RC4558
- Half a 4558, the first of six all-pass stages.
- R11, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R12, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C7, 6.8βnF
- This stageβs 6.8 nF. All six are the same, so the stages turn together.
- R13, 220βkΞ©
- Across the cell, 220 kΞ©.
- LDR2, VTL5C-type cell
- Another of the six cells around D3.
- IC2A, RC4558
- Half a 4558, all-pass stage 2.
- R14, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R15, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C8, 6.8βnF
- This stageβs 6.8 nF. All six are the same, so the stages turn together.
- R16, 220βkΞ©
- Across the cell, 220 kΞ©.
- LDR3, VTL5C-type cell
- Another of the six cells around D3.
- IC3B, RC4558
- Half a 4558, all-pass stage 3.
- R17, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R18, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C9, 6.8βnF
- This stageβs 6.8 nF. All six are the same, so the stages turn together.
- R19, 220βkΞ©
- Across the cell, 220 kΞ©.
- LDR4, VTL5C-type cell
- Another of the six cells around D3.
- IC3A, RC4558
- Half a 4558, all-pass stage 4.
- R20, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R21, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C10, 6.8βnF
- This stageβs 6.8 nF. All six are the same, so the stages turn together.
- R22, 220βkΞ©
- Across the cell, 220 kΞ©.
- LDR5, VTL5C-type cell
- Another of the six cells around D3.
- IC4B, RC4558
- Half a 4558, all-pass stage 5.
- R23, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R24, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C11, 6.8βnF
- This stageβs 6.8 nF. All six are the same, so the stages turn together.
- R25, 220βkΞ©
- Across the cell, 220 kΞ©.
- LDR6, VTL5C-type cell
- Another of the six cells around D3.
- IC4A, RC4558
- Half a 4558, all-pass stage 6.
- C12, 470βnF
- Couples the phaserβs output to the Feedback pot and the mixer.
- R26, 10βkΞ©
- The phased signal into IC6Aβs minus input.
- R29, 8.2βkΞ©
- IC6Aβs feedback. Against R26 the phased signal comes out inverted at 0.82.
- C14, 820βpF
- Across R29. It rolls the mixer off above about 24 kHz.
- C13, 1βΒ΅F
- Couples the dry signal to the mixerβs plus input.
- R27, 10βkΞ©
- The dry signal into IC6Aβs plus input.
- R28, 8.2βkΞ©
- With R27, a divider on the dry. IC6Aβs gain lifts it back, so the dry comes out at 0.82, the same as the phased signal.
- IC6A, RC4558
- Half a 4558, the mixer. It subtracts the phased signal from the dry at equal levels, so the notches go deep.
- R30, 18βkΞ©
- A load on IC6Aβs output.
- C15, 1βΒ΅F
- Output coupling cap.
- R31, 100βkΞ©
- Holds the output side of C15 at ground, so the footswitch doesnβt pop.
- R32, 560βΞ©
- Keeps a long cableβs capacitance off IC6A.
- IC5B, RC4558
- Half a 4558, a comparator. Its output flips to the other rail each time the triangle reaches a peak. D4 feeds this 4558βs positive supply pin, so its top rail is 0.6 V under +12 V.
- R33, 68βkΞ©
- Positive feedback that holds the comparator where it last flipped. Against R34 it sets the triangleβs height, 47 / 68 of the square.
- R34, 47βkΞ©
- From the triangle into the comparator.
- Rate, 25βkΞ© pot, audio taper
- Rate, 25 kΞ© audio, across the square. Its wiper sets how much of the square reaches the integrator, and that sets how fast the triangle ramps.
- R35, 120βΞ©
- Under Rate, so the slowest sweep never stops.
- R36, 39βkΞ©
- From Rateβs wiper into the integrator.
- C16, 470βnF
- The integratorβs cap. A steady current from R36 charges it, so the output ramps in straight lines.
- IC5A, RC4558
- The other half, the integrator. Its output is the triangle.
- Depth, 10βkΞ© pot, audio taper
- Depth, 10 kΞ© audio, across the triangle. Its wiper sends part of the sweep to the LED driver, so it sets how far the notches move. At 0 they hold where the Offset trim sets them.
- R37, 560βΞ©
- Under Depth.
- R38, 68βkΞ©
- The sweep from Depthβs wiper into the LED driver.
- R42, 2.2βkΞ©
- From +12 V to the top of the Offset trim.
- Offset, 10βkΞ© pot, linear taper
- The Offset trim, 10 kΞ©. It sets where the LED rests with Depth at 0. Set at 0.4, so the LED just goes dark at the bottom of a full-Depth sweep (assumed).
- R41, 2.2βkΞ©
- From the bottom of the Offset trim to ground.
- R40, 47βkΞ©
- The Offset trimβs voltage into the LED driver.
- R39, 3.6βkΞ©
- With R38 and R40 it makes a divider, so the driver sees a small share of the sweep with the offset added.
- IC6B, RC4558
- Half a 4558, the LED driver. It drives Q1 until the voltage under the LED, fed back through R43, matches its plus input.
- Q1, 2N3904
- Emitter follower that carries the LEDβs current from +12 V.
- D3, Red LED
- The LED in the middle of the six cells. Its light follows its current.
- R43, 220βkΞ©
- Feedback from under the LED to IC6Bβs minus input. With R44 it sets the driverβs gain at about 4.2.
- R44, 68βkΞ©
- From IC6Bβs minus input to ground.
- R45, 10βkΞ©
- With D2, a second leg from the minus input to ground. Once the minus input is over about half a volt it draws current, and the driverβs gain rises to about 26, so the LEDβs current climbs faster at the top of the sweep.
- D2, 1N914 / 1N4148
- The knee in the driverβs curve.
- Range, 1βkΞ© pot, linear taper
- The Range trim, 1 kΞ© used as a variable resistor under the LED. More resistance means less current for the same drive, so a narrower sweep. Set at half, the starting point in the kitβs notes.
- R46, 220βΞ©
- The least resistance under the LED, so Range at 0 canβt short it to ground.
About this version
- Stock
- The original runs from the mains on Β±12 V. In the model these are the battery part at 12 V and a β12 V source. RC4558 op-amps, a red LED lighting six VTL5C-type cells.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.