LED and photocell envelope filter, late 1970s style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the DOD 440 Envelope Filter.
An auto-wah. The guitar’s peaks light an LED inside a light-tight module, and its two photocells set the peak of a Wien bridge filter. Level sets how hard you have to play, Range where the peak rests and how far it moves.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Two paths leave R1. One is the filter. U1B is an inverting stage with a Wien bridge, a resistor-and-capacitor network tuned to one frequency, in its positive feedback. Away from that frequency the response is flat, about 2.5 dB under the input level. At it there is a peak about 10 to 14 dB tall. The peak’s frequency is 1 / (2π R C), where R is one half of the cell in parallel with its 220 kΩ and C is 20 nF. The other path is the envelope. U1A’s gain runs from 5 at Level 0 to about 45 at full. C7, D1 and D2 double its peaks into C8, and C8 drives the LED through R12. Range feeds the LED a resting current, from none at 0 to about 0.06 mA at full, so the peak rests between about 40 Hz and 260 Hz. A hard pick with Level at full charges C8 to about 4.7 V, which puts about 0.17 mA in the LED, and the peak rises to near 500 Hz. As C8 drains the peak falls back over about half a second. The cell’s figures are typical of a VTL5C module, assumed, so the real sweep may differ. The footswitch selects the filter or the input jack.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R4, 22 kΩ
- Top of the Vbias divider, from the battery.
- R5, 22 kΩ
- Bottom of the Vbias divider. With R4 it sets Vbias at 4.5 V.
- C2, 10 µF electrolytic
- Filters Vbias, so the filter’s cell and R3 return to a quiet point.
- C1, 10 nF
- Input coupling cap.
- R1, 10 kΩ
- In series with the input. Both op-amps are fed from its far end.
- R2, 100 kΩ
- From the input to the filter input. With R3 it halves the guitar into the filter.
- R3, 100 kΩ
- Holds the filter input at Vbias.
- R6, 220 kΩ
- Into U1B’s minus input from the filter input.
- R7, 430 kΩ
- U1B’s feedback. Away from the peak the gain from the input jack is about minus 2.5 dB.
- U1B, TL022
- Half of the TL022, the filter. Its plus input is the cell’s tap, fed back from the output through the Wien bridge.
- LDR1, VTL5C-type cell
- Half of the photocell, from the tap to Vbias. With R8 and C3 it is the Wien bridge’s parallel arm. Lit, its resistance drops and the peak rises. The cell’s figures are typical of a VTL5C module and assumed.
- R8, 220 kΩ
- Across LDR1. It limits how high the arm’s resistance can go, so the peak never rests below about 36 Hz. Drawn as one of a pair under one 220k label.
- C3, 20 nF
- The Wien bridge’s parallel cap.
- LDR2, VTL5C-type cell
- The other half of the photocell, lit by the same LED. With R9 and C4 it is the Wien bridge’s series arm.
- R9, 220 kΩ
- Across LDR2, as R8 is across LDR1.
- C4, 20 nF
- The Wien bridge’s series cap, from the output.
- C5, 50 nF
- Output coupling cap, to the footswitch.
- U1A, TL022
- The other half of the TL022, the envelope amp. Its gain is 1 plus 470 kΩ over R11 and Level.
- R10, 470 kΩ
- U1A’s feedback resistor.
- R11, 10 kΩ
- Sets U1A’s highest gain, about 45 with Level at full.
- C6, 100 nF
- Blocks DC from the gain leg, so U1A sits at Vbias.
- Level, 100 kΩ pot, reverse audio taper
- Level, 100 kΩ reverse audio, a variable resistor in U1A’s gain leg. Clockwise there is less resistance and more gain, so softer playing moves the filter. At 0 the gain is about 5, at full about 45.
- C7, 4.7 µF electrolytic
- Couples U1A to the rectifier.
- D1, 1N914 / 1N4148
- Clamps C7’s far side near ground on the down swings, so D2 sees the whole swing.
- D2, 1N914 / 1N4148
- Charges C8 on the peaks.
- C8, 1 µF electrolytic
- The envelope cap. It charges fast through D2 and drains through R12 into the LED and the Range network.
- R12, 22 kΩ
- Carries C8’s voltage into the LED. The LED drops about 1.6 V, so its current is C8’s voltage minus 1.6 V, over 22 kΩ.
- LED, Red LED
- The module’s LED. Its light follows its current. It runs from about 0.03 mA at rest to about 0.2 mA on a hard pick.
- R13, 100 kΩ
- From 9 V to the top of Range.
- Range, 100 kΩ pot, linear taper
- Range, 100 kΩ, its wiper on the LED. Clockwise it feeds the LED a resting current, about 0.06 mA at full, so the peak rests higher. Counterclockwise it pulls the LED’s node toward 0.9 V and diverts part of the envelope’s current. Taper and direction assumed.
- R14, 22 kΩ
- From the bottom of Range to ground.
About this version
- Stock
- Negative ground, 9 V. TL022 op-amps, a red LED lighting two VTL5C-type cell halves.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.