Two 6EU7 channels into a cathodyne and two 7591s, early 1960s
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Gibson GA-40T Les Paul.
Two channels, each two 6EU7 stages with a bridged-T filter and a volume, mixed into one Tone control and a 12AU7 stage. A cathodyne drives two 7591s in fixed bias. The tremolo is left out.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each channel has two 6EU7 stages. Between them a bridged-T filter, two 220 kΩ resistors with 500 pF across both and .0033 µF from their middle to ground, dips the mids ahead of the volume. Channel I’s coupling cap is .001 µF and channel II’s .01 µF, so channel I has much less bass. The two second stages mix through 220 kΩ each. At the mix node 750 pF and 68 kΩ go to ground, and the Tone pot’s wiper sits there. Toward one end it reaches .02 µF to ground and cuts the treble. Toward the other it reaches .001 µF from channel II’s plate and lets more of channel II’s treble through. Half a 12AU7 drives a 6EU7 cathodyne and two 7591s in fixed bias from their own negative supply. There’s no feedback. The tremolo, a lamp and light-dependent resistor across channel II’s output, is left out. The transformer figures are typical for the size.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R2, 68 kΩ
- Channel I’s input 1 resistor into the grid. With nothing plugged into input 2, this resistor and input 2’s resistor are in parallel, so a guitar in input 1 goes through 34 kΩ to the grid. That is enough to stop radio pickup and too little to cut treble.
- R3, 68 kΩ
- Channel I’s input 2 resistor into the grid. With nothing plugged into input 1, input 1’s tip is grounded, and the two 68 kΩ resistors form a divider. Input 2 is about 6 dB quieter and loads the guitar with 136 kΩ.
- R1, 1 MΩ
- Input 1’s 1 MΩ to ground. It sets the load a guitar in input 1 sees, and with a patch lead in input 1 it is the end of the lead’s path.
- R14, 68 kΩ
- Channel II’s input 1 resistor into the grid. With nothing plugged into input 2, this resistor and input 2’s resistor are in parallel, so a guitar in input 1 goes through 34 kΩ to the grid. That is enough to stop radio pickup and too little to cut treble.
- R15, 68 kΩ
- Channel II’s input 2 resistor into the grid. With nothing plugged into input 1, input 1’s tip is grounded, and the two 68 kΩ resistors form a divider. Input 2 is about 6 dB quieter and loads the guitar with 136 kΩ.
- R13, 1 MΩ
- Input 1’s 1 MΩ to ground. It sets the load a guitar in input 1 sees, and with a patch lead in input 1 it is the end of the lead’s path.
- V1a, 6EU7
- 6EU7, first half: channel I’s first stage.
- R4, 1.5 kΩ
- Cathode resistor for V1a, 1.5 kΩ (R4). The drawing shows 1.15 V.
- C1, 20 µF electrolytic
- Bypass for V1a’s cathode resistor, 20 µF (C1).
- R5, 100 kΩ
- Plate resistor for V1a, 100 kΩ (R5). The drawing shows 150 V.
- C2, 1 nF
- Coupling cap into channel I’s filter, .001 µF (C2). Against the filter’s 940 kΩ it cuts the bass below about 170 Hz.
- R6, 220 kΩ
- First 220 kΩ of the filter (R6).
- R7, 220 kΩ
- Second 220 kΩ of the filter (R7), to the top of Volume I.
- C3, 500 pF
- The filter’s 500 pF (C3), across both 220 kΩ resistors. It passes the treble around them.
- C4, 3.3 nF
- The filter’s .0033 µF (C4), from the middle of the two 220 kΩ to ground. With C3 it makes a bridged-T: the mids dip, the bass and treble pass.
- R8, 500 kΩ pot, audio taper
- Volume I, 500 kΩ audio (R8).
- R10, 100 kΩ
- Grid stopper, 100 kΩ (R10), from the volume’s wiper to V2a.
- V2a, 6EU7
- 6EU7, first half of the second tube: channel I’s second stage.
- R9, 1.5 kΩ
- Cathode resistor for V2a, 1.5 kΩ (R9). The drawing shows 1.55 V.
- C5, 100 nF
- Bypass for V2a’s cathode, only .1 µF (C5). It bypasses the treble, from about 1 kHz up, so the bass gets less gain.
- R11, 100 kΩ
- Plate resistor for V2a, 100 kΩ (R11).
- R12, 220 kΩ
- Channel I’s mixing resistor, 220 kΩ (R12), from V2a’s plate to the mix node.
- V1b, 6EU7
- 6EU7, second half: channel II’s first stage.
- R16, 1.5 kΩ
- Cathode resistor for V1b, 1.5 kΩ (R16). The drawing shows 1.1 V.
- C6, 20 µF electrolytic
- Bypass for V1b’s cathode resistor, 20 µF (C6).
- R17, 100 kΩ
- Plate resistor for V1b, 100 kΩ (R17). The drawing shows 135 V.
- C7, 10 nF
- Coupling cap into channel II’s filter, .01 µF (C7), ten times channel I’s, so channel II keeps its bass.
- R18, 220 kΩ
- First 220 kΩ of channel II’s filter (R18).
- R19, 220 kΩ
- Second 220 kΩ of the filter (R19), to the top of Volume II.
- C8, 500 pF
- The filter’s 500 pF (C8), across both 220 kΩ resistors.
- C9, 3.3 nF
- The filter’s .0033 µF (C9), from the middle to ground.
- R20, 500 kΩ pot, audio taper
- Volume II, 500 kΩ audio (R20).
- R22, 100 kΩ
- Grid stopper, 100 kΩ (R22), to V2b.
- V2b, 6EU7
- 6EU7, second half of the second tube: channel II’s second stage. On the amp the tremolo’s light-dependent resistor sits across its output. It’s left out here.
- R21, 1.5 kΩ
- Cathode resistor for V2b, 1.5 kΩ (R21). The drawing shows 1.15 V.
- C10, 20 µF electrolytic
- Bypass for V2b’s cathode resistor, 20 µF (C10).
- R23, 100 kΩ
- Plate resistor for V2b, 100 kΩ (R23). The drawing shows 145 V.
- R24, 220 kΩ
- Channel II’s mixing resistor, 220 kΩ (R24).
- C13, 750 pF
- A fixed treble cut, 750 pF (C13) from the mix node to ground.
- R52, 68 kΩ
- 68 kΩ (R52) from the mix node to ground. With the 220 kΩ mixing resistors it drops each channel’s level to about a quarter.
- R25, 2 MΩ pot, audio taper
- Tone, 2 MΩ audio (R25), its wiper on the mix node. Clockwise the wiper moves toward the .001 µF from V2b’s plate, which adds channel II’s treble. Counterclockwise it moves toward the .02 µF to ground, which cuts the treble on both channels. The drawing doesn’t mark which way it turns.
- C11, 1 nF
- .001 µF (C11) from the Tone pot’s bright end to V2b’s plate. Channel II’s treble goes around its mixing resistor through it.
- C12, 20 nF
- .02 µF (C12) from the Tone pot’s dark end to ground.
- C14, 5 nF
- Coupling cap to V3b, .005 µF (C14).
- R26, 470 kΩ
- V3b’s grid resistor, 470 kΩ (R26).
- V3b, 12AU7 / ECC82
- 12AU7, one half: the gain stage after the mix. It drives the cathodyne.
- R27, 1.5 kΩ
- Cathode resistor for V3b, 1.5 kΩ (R27). The drawing shows 3.8 V.
- C15, 100 nF
- Bypass for V3b’s cathode, .1 µF (C15), from about 1 kHz up.
- R28, 100 kΩ
- Plate resistor for V3b, 100 kΩ (R28), from the +305 V node. The drawing shows 87 V on the plate.
- .005µ, 5 nF
- Coupling cap into the cathodyne.
- V4a, 6EU7
- 6EU7, a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 100k, 100 kΩ
- The cathodyne’s plate resistor, the output to tube B.
- 3.3k, 3.3 kΩ
- The cathodyne’s bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 100k, 100 kΩ
- The cathodyne’s cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470 kΩ
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathode’s high DC voltage. It’s the grid’s only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ω.
- .02µ, 20 nF
- Coupling cap to tube A’s grid.
- .02µ, 20 nF
- Coupling cap to tube B’s grid.
- 1.5k, 1.5 kΩ
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current.
- 1.5k, 1.5 kΩ
- Grid stopper for tube B.
- V5, 7591
- 7591A, tube A of the push-pull pair, cathode grounded, biased from the fixed bias supply.
- V6, 7591
- 7591A, tube B of the pair.
- 220k, 220 kΩ
- Grid leak for tube A, returned to the bias supply. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 220k, 220 kΩ
- Grid leak for tube B.
- 1k, 1 kΩ
- One screen resistor shared by both tubes, with no cap after it. It carries both screens’ current. The two screens’ signal currents are opposite and cancel in it, so its drop follows the even harmonics and grows as the stage is driven harder.
- 4 H, 4 H
- The choke from the reservoir cap to B+, as on the amp’s drawing. The output transformer’s center tap, the screens and everything after them hang past it, so all of their current runs through it. It passes DC with little drop. With the cap after it, it would filter ripple, but ripple isn’t modeled here. Typical of the part.
- 100, 100 Ω
- The choke’s winding resistance, typical. With the output tubes’ whole current through it, it’s most of the DC drop between the reservoir and B+.
- 10µ, 10 µF electrolytic
- Filter cap on B+ after the choke, where the output transformer’s center tap and the screens hang.
- 15k, 15 kΩ
- Dropping resistor from the screen supply node to the node for the driver and cathodyne, as on the Gibson GA-40T drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 10µ, 10 µF electrolytic
- Filter cap at the node for the driver and cathodyne. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 22k, 22 kΩ
- Dropping resistor from the node for the driver and cathodyne to the node for the preamp, as on the Gibson GA-40T drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 10µ, 10 µF electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- Tremolo, 41 kΩ
- Stands for the tremolo’s lamp driver (not modeled) on the screen supply node. It pulls about the current worked out from the voltages on the drawing. That part of the amp isn’t modeled here. A typical value.
- Oscillator, 150 kΩ
- Stands for the tremolo’s oscillator (not modeled) on the node for the driver and cathodyne. It pulls about the current worked out from the voltages on the drawing. That part of the amp isn’t modeled here. A typical value.
- OT, 6.6 kΩ to 8 Ω, 30 H primary, 12 mH leakage
- The output transformer, 6.6 kΩ plate to plate into 8 Ω, center tap on B+ after the choke. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 375 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 375 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 375 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 60 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 60 Ω
- Resistance of the other half. Typical of the part.
- V7, GZ34
- One plate of the GZ34 rectifier. It conducts near the peak of its half of the winding, and its own drop rises with the current, which adds to the sag.
- V7, GZ34
- The rectifier’s other plate, on the other half cycle.
- 20µ, 20 µF electrolytic
- The reservoir cap. It feeds the choke, and past it the output transformer’s center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- PT, 375 V ac, 60 Hz
- The end of the high-voltage winding the bias comes off, 375 V ac, the same end as the rectifier’s first plate. It’s drawn as its own source so the bias supply’s average can be found. Keep it equal to the winding beside the rectifier.
- 390k, 390 kΩ
- Series resistor into the bias rectifier, 390k Ω. There’s no bias tap, so the bias comes straight off the high-voltage winding, and this resistor drops most of it.
- Bias diode, 1N4001
- The bias rectifier, a silicon diode turned so the supply comes out negative.
- 20µ, 20 µF electrolytic
- Filter cap on the bias supply, its plus side to ground.
- 4.7k, 4.7 kΩ
- Second resistor of the bias supply, 4.7k Ω to the bias line. With the cap after it, it filters the ripple a second time.
- 20µ, 20 µF electrolytic
- Second filter cap, on the bias line, its plus side to ground.
- 51k, 51 kΩ
- From the bias line to ground, 51k Ω. With the 4.7k Ω and 390k Ω above it, it divides the supply down to the bias. There’s no bias pot, so change this resistor to change the bias. Bigger runs the tubes colder.
- Coil R, 8.69 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 8 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 464 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 2.19 Ω
- Limits what Loss L2 adds.
- Tank R, 83.7 Ω
- Height of the bass resonance, about 92 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 21.1 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The 6EU7, 12AU7 and 7591 are the bench’s models. The transformers and the choke are typical, not on the drawing.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.