Inductor wah with a four-way tone switch, 1970s style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Electro-Harmonix Wah-Wah pedal.
A Vox-style inductor wah with a four-position Tone switch that picks the feedback cap, and a Mode Selector that turns it into a volume pedal. Its 15 kΞ© base resistor runs it much hotter than a Vox.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 amplifies the guitar, and Q2 sends part of its output back to Q1βs base through the feedback caps and the inductor. At one frequency that feedback adds, so the response peaks there. The treadle sets how much of Q1βs output reaches Q2, so it moves the peak, from about 630 Hz heel down to about 3 kHz toe down with Tone at .0033. Each Tone position adds its cap beside C3 and moves the whole sweep down, to about 175 to 710 Hz at .1. R2 is 15 kΞ© where the Vox has 1.5 kΞ©, so less feedback reaches the base. The gain is about 11 dB at 100 Hz and about 30 dB at the peak, against about minus 13 dB and 15 dB for the Vox. The pedal clips on a hard pick. In Volume the transistors are out of the path, the treadle pot is fed from the input jack, and the output comes from its wiper. The Reverse switch, which swaps the treadleβs ends, is set as drawn, and the footswitch is left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R1, 68βkΞ©
- Input resistor. The feedback arriving at the base works against it.
- C1, 22βnF
- Input coupling cap.
- R2, 15βkΞ©
- From the feedback node to Q1βs base, 15 kΞ© where the Vox has 1.5 kΞ©. It carries the bias and the feedback.
- Q1, 2N5088
- 2N3565, the gain stage.
- R3, 22βkΞ©
- Q1βs collector load.
- R4, 470βΞ©
- Q1βs emitter resistor. The drawing marks it 470 kΞ©, which leaves Q1 almost off and the pedal silent, so 470 Ξ©, the Vox value, is used.
- R5, 470βkΞ©
- Bias feedback from Q1βs collector to the inductorβs top, so the stage biases itself through the inductor and R2.
- R6, 100βkΞ©
- Bottom of the bias divider.
- C2, 5βΒ΅F electrolytic
- Grounds the inductorβs top for audio.
- L1, 500βmH
- The wah inductor, 500 mH. With the feedback caps it sets where the peak sweeps.
- R7, 33βkΞ©
- Across the inductor. It damps the peak.
- R8, 470βkΞ©
- Biases Q2 from Q1βs collector.
- Q2, 2N5088
- 2N3565, an emitter follower that drives the feedback caps.
- R9, 1βkΞ©
- Q2βs collector resistor.
- R10, 10βkΞ©
- Q2βs emitter load.
- C3, 2.2βnF
- The fixed feedback cap, always in.
- CT1, 3.3βnF
- Tone cap, .0033 Β΅F, beside C3 in the first position.
- CT2, 10βnF
- Tone cap, .01 Β΅F.
- CT3, 47βnF
- Tone cap, .047 Β΅F.
- CT4, 100βnF
- Tone cap, .1 Β΅F, the position drawn.
- C4, 200βnF
- From Q1βs collector to the treadle and, in Wah, the output.
- Treadle, 100βkΞ© pot, linear taper
- The treadle pot, 100 kΞ©. In Wah it divides Q1βs output down before Q2, which sets how much feedback reaches J and so where the peak sits. In Volume it is the volume control. The taper is not marked. Linear is assumed.
- C5, 200βnF
- Couples the treadleβs wiper to Q2βs base.
About this version
- Stock
- Negative ground, 9 V. Two 2N3565 transistors (a 2N5088 model stands in) and a 500 mH inductor.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.