BBD flanger on 18 V, 1979 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Ibanez FL-301 Flanger.
A bucket-brigade chip delays the guitar a few milliseconds, and the delayed copy is mixed back with the dry signal. A slow oscillator moves the delay, so the comb of notches sweeps. Knobs Speed, Width and Regeneration.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC101B lifts the treble up to 11 times above about 1 kHz before the delay, and the mixer cuts it back by the same amount, so the hiss the delay chip adds is cut too. IC102B adds the regeneration. Q101 and its two 24 kΩ resistors make a low-pass near 10 kHz in front of the MN3007, and IC102A another near 7.7 kHz after it, to keep the clock out of the audio. The MN3007 has 1024 stages, so the delay is 512 clock periods. The MN3101 clock runs faster the more current Q107B pulls, and the LFO’s triangle reaches Q107B’s base through Width and R149. At Width 5 the clock runs between about 240 and 390 kHz, a delay of 1.3 to 2.1 ms. At full Width it runs from about 200 to 500 kHz, 1.0 to 2.6 ms. Dry and wet meet at equal level in IC101A, so the notches go deep. Speed runs from one sweep every 16 seconds to about 13 a second. C124 smooths the control node, so fast sweeps are narrower. There are no service notes for the clock’s range, so its scale, the CLOCK trimmer’s setting and the LFO caps’ value are assumed.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C129, 10 µF electrolytic
- Across the 18 V supply, at the regulator’s input.
- IC106, 12 V
- An MC78L12 regulator. Modeled as a steady 12 V source. Everything but the battery runs from it.
- C130, 100 µF electrolytic
- The 12 V line’s filter cap.
- R156, 4.7 kΩ
- Top of the bias divider.
- VR102, 10 kΩ pot, linear taper
- The BIAS trimmer, 10 kΩ. Its wiper is the 6 V bias line every stage sits on. Set at the middle, 6 V, as the drawing marks.
- R157, 4.7 kΩ
- Bottom of the bias divider.
- C131, 47 µF electrolytic
- The bias line’s filter cap. It makes the line a quiet AC ground.
- C101, 47 nF
- Input coupling cap.
- R101, 1 kΩ
- In series with IC101B’s plus input.
- R102, 510 kΩ
- Biases IC101B at 6 V. The guitar sees about 510 kΩ.
- IC101B, TL022
- Half a TL022, the input stage. Its gain is one for the bass and rises to 11 above about 1 kHz, a treble lift ahead of the delay. The mixer takes the lift back out.
- R104, 10 kΩ
- IC101B’s feedback.
- C102, 30 pF
- Across R104. It keeps the stage stable at radio frequencies.
- R103, 1 kΩ
- With R104 it sets the treble lift, 1 + 10 k / 1 k = 11.
- C103, 15 nF
- In series with R103. Below about 1 kHz it blocks R103, so the bass passes at a gain of one.
- R105, 10 kΩ
- Into IC102B. With R107 it makes an inverting stage, a gain of one.
- R107, 10 kΩ
- IC102B’s feedback.
- C104, 30 pF
- Across R107, for stability.
- R106, 10 kΩ
- Holds IC102B’s plus input at 6 V.
- IC102B, TL022
- Half a TL022. It adds the regeneration to the signal going into the delay.
- R108, 4.7 kΩ
- The regeneration into IC102B.
- VR103, 10 kΩ pot, linear taper
- An internal trimmer, 10 kΩ, in series with R108. It sets how far Regeneration can go. Set at the middle, an assumed setting.
- C105, 1 µF electrolytic
- Couples the Regeneration pot to the trimmer.
- Regeneration, 10 kΩ pot, linear taper
- Regeneration, 10 kΩ B. It sends part of the delayed signal back into the delay. Up, the notches deepen and the peaks between them ring.
- C113, 1 µF electrolytic
- Couples the wet line to the top of Regeneration.
- R109, 24 kΩ
- First resistor of the filter in front of the delay.
- R110, 24 kΩ
- Second resistor of the filter.
- C106, 1 nF
- Feedback from Q101’s emitter. With C107 and the two 24 kΩ it makes a two-pole low-pass near 10 kHz, so the chip’s clock doesn’t mix with the guitar’s highs.
- C107, 470 pF
- The filter’s cap to ground.
- Q101, 2SC536F
- A 2SC536 emitter follower, the filter’s buffer.
- R111, 10 kΩ
- Q101’s emitter load.
- R112, 4.7 kΩ
- Into the delay chip.
- IC103, MN3007
- MN3007 delay line, 1024 stages. It holds 512 samples and passes each on after 512 clock periods. The two outputs are drawn as one pin. Its input range is centered on 5.3 V with 2.2 V either side, assumed for a 12 V supply.
- IC104, MN3101
- MN3101 clock. Its timing cap C123 is 180 pF. The more current Q107 pulls from it, the faster the clock runs and the shorter the delay. Q106, R140, R141 and R142 around the chip’s oscillator are inside this part.
- R113, 56 kΩ
- The delay chip’s output load, pulled up toward 12 V. The MN3007 is a P-channel part.
- R114, 3.9 kΩ
- Feeds R113 from 12 V.
- C108, 1 µF electrolytic
- Filters the supply for R113.
- C109, 1 µF
- A 1 µF non-polar cap from the delay chip.
- R115, 24 kΩ
- Into the filter after the delay.
- C110, 2.2 nF
- The filter’s cap to ground.
- R117, 24 kΩ
- The filter’s feedback.
- R116, 10 kΩ
- Into IC102A’s minus input.
- C111, 820 pF
- With C110 and the resistors it makes a two-pole low-pass that strips the clock off the delayed signal.
- R118, 10 kΩ
- Holds IC102A’s plus input at 6 V.
- IC102A, TL022
- Half a TL022, the filter after the delay.
- C112, 1 µF
- A 1 µF non-polar cap to the wet line.
- R119, 100 kΩ
- Holds the wet line at 6 V on Q102’s input side.
- R120, 100 kΩ
- Holds the wet line at 6 V on Q102’s output side. Q102 is drawn as a wire, so R119 and R120 sit side by side.
- C114, 1 µF
- A 1 µF non-polar cap to the mixer.
- R121, 51 kΩ
- The wet signal into the mixer.
- R122, 51 kΩ
- The dry signal into the mixer, from IC101B, equal to R121.
- R124, 51 kΩ
- The mixer’s feedback. Each input comes out at a gain of one.
- C115, 51 pF
- Across R124, for stability.
- C116, 3 nF
- With R123 across the feedback it cuts the treble by up to 11 times, taking back IC101B’s lift. The hiss and clock noise the delay adds are cut with it.
- R123, 5.1 kΩ
- In series with C116.
- R125, 3.3 kΩ
- Holds the mixer’s plus input at 6 V.
- IC101A, TL022
- Half a TL022, the mixer. Where the delayed copy is half a cycle behind the dry signal, the two cancel.
- R126, 470 Ω
- In series with the output.
- C117, 16 µF electrolytic
- Output coupling cap.
- R127, 10 kΩ
- Holds the output at ground.
- R143, 1 kΩ
- From the clock’s timing pin to Q107B.
- Q107B, 2SC1815
- Half of a 2SC1583F pair. It pulls the clock’s timing current, about its gain times the current into its base, so the control node sets the clock.
- Q107A, 2SC1815
- The other half, its base tied to its collector, with R144 across it. It carries a fraction of a microamp from R145.
- R145, 22 MΩ
- From 12 V to Q107A, a few tenths of a microamp.
- R144, 18 kΩ
- Across Q107A.
- C124, 10 µF electrolytic
- A tantalum cap on the control node. With the resistors feeding it, it smooths the sweep more as Speed goes up.
- R148, 100 kΩ
- From the control node to ground.
- R146, 1 MΩ
- The CLOCK trimmer into the control node.
- R147, 1 kΩ
- From 12 V to the top of VR101.
- VR101, 10 kΩ pot, linear taper
- The CLOCK trimmer, 10 kΩ. It sets the clock with the LFO at rest, so it places the sweep. Set at 0.2, an assumed setting.
- R149, 510 kΩ
- Width’s wiper into the control node.
- R152, 5.1 kΩ
- Top of the LFO’s reference divider.
- R153, 5.1 kΩ
- Bottom of the LFO’s reference divider, 6 V.
- C128, 100 µF electrolytic
- The LFO reference’s filter cap.
- IC105B, TL022
- Half a TL022, an integrator. Its output ramps up and down, the triangle that sweeps the delay.
- C125, C126, 23.5 µF
- Two 47 µF caps back to back, 23.5 µF with no polarity. The drawing marks them “10/47”, read here as 47 µF, an assumption. With R151 and Speed they set how fast the triangle ramps.
- R151, 1.8 kΩ
- In series with Speed. It sets the top speed.
- Speed, 500 kΩ pot, reverse audio taper
- Speed, 500 kΩ C taper, a variable resistor from the square wave into the integrator. At full it’s out of the path, the fastest setting.
- IC105A, TL022
- Half a TL022, a Schmitt trigger. It flips each time the triangle reaches a switch point.
- R154, 27 kΩ
- From the triangle to the trigger’s plus input.
- R155, 82 kΩ
- Positive feedback. With R154 it sets the triangle’s height, about a third of the square’s.
- C127, 10 nF
- From the output to the minus input.
- R150, 100 kΩ
- Holds the trigger’s minus input at the LFO reference.
- Width, 100 kΩ pot, linear taper
- Width, 100 kΩ B, across the triangle. It sets how much of the triangle moves the clock, so how far the delay sweeps.
About this version
- Stock
- The circuit as the factory drawing shows it, on 18 V with a 12 V regulator. TL022 op-amps, an MN3007 delay line and an MN3101 clock.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.