Two-channel variable-mu tube limiter, 1959 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Fairchild 670 Stereo Limiter.
One channel of a two-channel limiter. Eight remote-cutoff triode sections, four a side, make one push-pull stage whose gain falls as their grids go negative. A separate amplifier ending in two 6973s and a bridge rectifier pulls the grids down from a fixed bias, tens of volts in a few milliseconds, and the push-pull pair cancels the thump.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar reaches the unit through a DI box and line amp (20 dB), which aren’t part of it. Input gain feeds T101, which steps the signal up about 9.6 times and splits it at its center tap, so four 6386 sections on one side and four on the other are driven in opposite phase. The center tap carries the control voltage. At rest it sits at the bias that Zero sets, about −7 V. The 6386 is a remote-cutoff triode: as its grid goes more negative its gain falls smoothly, and the push-pull pair cancels the thump of that change while the signal adds. T102 steps the plates down into the 600 Ω line, about 9 dB of gain with Input gain full. The sidechain listens to the output through T103. V105 sits just past cutoff, and DC threshold sets how far past, so it passes only the peaks that rise above that. V106 and the two 6973s build those peaks up, T104 steps them down, and the bridge rectifies them into tens of volts below the bias, so the pull down comes within a few milliseconds. Threshold sets how much of the output reaches V105. Time constant sets how fast the control line lets go, from about 0.1 s in position 1 to about 1.8 s in position 4. Positions 5 and 6 add slower capacitors that only fill on a long loud passage. DC threshold starts where the factory set it, so the output stops rising near +3 dBm. The meter reads the eight sections’ plate current, which falls about as fast as the gain, so it reads the limiting in dB. On the real unit a switch sets both channels to work on left and right, or on the sum and difference of the two (lateral and vertical, for cutting stereo records). Only one channel is built here.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- DI in, 1 MΩ
- Not part of the unit: the DI box’s input resistance, 1 MΩ, as a guitar amp’s.
- DI box, 10 V
- Not part of the unit: a DI box with a line amp behind it, 20 dB of gain and a 50 Ω output, as a guitar would be brought up to line level in a studio before a limiter. The unit itself has only about 9 dB of gain.
- Input gain, 600 Ω pot, audio taper
- AT101, Input gain. On the real unit it’s a 600 Ω T-pad step attenuator, 1 dB a step. Here it’s a 600 Ω audio-taper pot. It sets how hard the signal drives the 6386s, so with the thresholds fixed it sets how much the unit limits.
- T101, 600 Ω to 55.3 kΩ, 4 H primary, 3 mH leakage
- The input transformer, a UTC Y-6431: 600 Ω to 55 kΩ, 1:9.6, its two primary halves in series in this mode. Each half of the secondary feeds one side’s four grids, in opposite phase. The center tap carries the control voltage to all eight. Tap any piece of it to change its figures.
- R101, 180 Ω
- R101, 180 Ω 1 %, across one half of T101’s primary. With R102 it terminates the input, so the source sees a steady load.
- R102, 180 Ω
- R102, 180 Ω 1 %, across the other half of the primary. Drawn here in series with R101 across the whole primary, which is the same while the halves match.
- V101a, V102a, V103b, V104b, 6386
- Four 6386 sections in parallel, drawn as one: side A of the push-pull stage. The 6386 is a remote-cutoff triode, its grid wound unevenly, so as the control voltage goes more negative its gain falls smoothly instead of cutting off. This is the gain cell.
- V101b, V102b, V103a, V104a, 6386
- The other four sections, side B, driven in opposite phase. The control voltage moves all eight grids together, so the thump of the gain change cancels in the push-pull pair while the signal adds.
- R103, 680 Ω
- R103, 680 Ω 1 W, cathode bus A to the Balance pots.
- R104, 680 Ω
- R104, 680 Ω 1 W, the Balance pots to cathode bus B.
- Balance, 100 Ω pot, linear taper
- R105A, Balance, 100 Ω between R103 and R104, its wiper on ground, ganged with R105B the other way round. A front-panel screwdriver control. Turned, it lifts one side’s cathode return and lowers the other’s, so the two sides’ currents can be matched and the control voltage’s thump cancels. Taper assumed linear.
- Balance (B), 100 Ω pot, linear taper
- R105B, the other half of Balance, across the same two points with its wiper on the bias supply. The two pots make a divider between ground and the bias supply, so the cathodes return a few volts below ground.
- C101, C102, 40 µF
- C101, C102, from cathode bus A to bus B: 4 µF 200 V on the drawing, 40 µF here so the low end stays flat against T102’s light load (chosen with T102, so the meter tracks). It bypasses the cathodes for the push-pull signal, which is opposite on the two buses, and leaves the control voltage’s common move unbypassed.
- T102, 1.5 kΩ to 600 Ω, 20 H primary, 4 mH leakage
- The output transformer, about 1.6:1, so the 600 Ω line looks like 1.5 kΩ plate to plate. The drawing lists no figures for it. This load is chosen so the meter follows the gain reduction, as the real units’ meters do: against a load this light the 6386s’ gain falls with their current. Against the 48.6 kΩ of the replacement transformers made for these units, the gain hardly moved while the current fell, and the meter dropped off the scale by about 7 dB of limiting. Its two secondaries are in series in this mode. Tap any piece of it to change its figures.
- R111, 33 Ω
- R111, 33 Ω 1 W, from the regulated line to the meter shunts’ joint.
- R107, 30 Ω
- R107, 30 Ω 1 %, carries the upper half’s plate current from the joint to T102 (pin 3). The meter reads the voltage across it.
- R108, 30 Ω
- R108, 30 Ω 1 %, the same for the lower half (T102 pin 2).
- R106, 4.7 kΩ
- R106, 4,700 Ω 1 %, in series with the meter.
- M101, 3.9 kΩ
- M101, the meter: a VU meter with its rectifier taken out, a plain moving-coil movement, 3,900 Ω (typical, not on the drawing). In Zero it reads the eight 6386 sections’ plate current: full current with no limiting, less as the control line pulls the grids down. At rest it carries 84 µA, the 0 VU mark: on the unit, Zero (R142) is set so the needle rests there. With T102’s light load the current falls about as fast as the gain, so the needle reads close to the limiting in dB: about −2.4 VU at 2.4 dB, −6 VU at 5.4 dB, −7.7 VU at 6.8 dB and −14 VU at 11 dB.
- Line, 600 Ω
- Not part of the unit: the 600 Ω line it drives.
- R145, 150 Ω
- R145, 150 Ω 5 %, from the output to T103. The sidechain listens to the output, so it limits what it has already turned down (feedback limiting).
- R148, 150 Ω
- R148, 150 Ω 5 %, from the output’s other side (grounded here) to T103. R146 and R147, two more 150 Ω, join the middles of T102’s and T103’s split windings, which carry no signal while the halves match, so they’re left out.
- R149, 680 Ω
- R149, 680 Ω 5 %, across one half of T103’s primary.
- R150, 680 Ω
- R150, 680 Ω 5 %, across the other half.
- T103, 600 Ω to 173 kΩ, 10 H primary, 3 mH leakage
- The sidechain’s input transformer, 1:17, its center tap grounded, so each half drives one grid of V105 in opposite phase. The secondary’s own resistance is left out (the tap is grounded straight). Tap any piece of it to change its figures.
- R113, 24 kΩ
- R113, 24 k 5 %, loads one half of T103’s secondary.
- R114, 24 kΩ
- R114, 24 k 5 %, loads the other half.
- Threshold, 100 kΩ pot, linear taper
- R115A, Threshold (AC threshold on the drawing), 100 k linear across one half of T103’s secondary, wiper to V105a’s grid, ganged with R115B. Turned up, more of the output reaches the sidechain, so limiting starts at a lower output level.
- Threshold (B), 100 kΩ pot, linear taper
- R115B, the other half of the ganged Threshold, across the other half of the secondary, wiper to V105b’s grid. The drawing prints 180 k for this half. It’s built as 100 k, the same as R115A, so the two sides match.
- V105a, 12AX7 / ECC83 / 7025
- Half a 12AX7, the sidechain’s first stage, one side of a push-pull pair.
- V105b, 12AX7 / ECC83 / 7025
- The other half of the 12AX7, in opposite phase.
- R118, 1 MΩ
- R118, 1 M from the regulated line to V105’s cathodes, part of their bias.
- R119, 18 kΩ
- R119, 18 k, V105’s cathode resistor.
- DC threshold, 100 kΩ pot, linear taper
- R117, DC threshold, 100 k from V105’s cathodes to ground, a screwdriver control inside the chassis. Its wiper takes current from the regulated line through R116. Turned toward the cathode end it lifts the cathodes, biasing V105 further past cutoff, so the sidechain needs more signal before it acts. Taper assumed linear.
- R116, 270 kΩ
- R116, 270 k, from the regulated line to DC threshold’s wiper.
- R120, 100 kΩ
- R120, 100 k 1 W 5 %, V105a’s plate resistor.
- R121, 100 kΩ
- R121, 100 k 1 W 5 %, V105b’s plate resistor.
- C103, 50 nF
- C103, .05 µF 400 V, V105a’s plate to V106a’s grid.
- C104, 50 nF
- C104, .05 µF 400 V, V105b’s plate to V106b’s grid.
- R122, 1 MΩ
- R122, 1 M, V106a’s grid resistor.
- R123, 1 MΩ
- R123, 1 M, V106b’s grid resistor.
- V106a, 12BH7 (GE, JJ)
- Half a 12BH7A, the driver for V107.
- V106b, 12BH7 (GE, JJ)
- The other half of the 12BH7A, the driver for V108.
- R126, 100 kΩ
- R126, 100 k 2 W, V106a’s plate resistor, from the raw line.
- R127, 100 kΩ
- R127, 100 k 2 W, V106b’s plate resistor.
- R124, 1 kΩ
- R124, 1,000 Ω 1 W 5 %, V106a’s cathode resistor, unbypassed.
- R125, 1 kΩ
- R125, 1,000 Ω 1 W 5 %, V106b’s cathode resistor.
- R128, 2.7 kΩ
- R128, 2,700 Ω 1 W 5 %, from V106a’s cathode to one end of T104’s feedback winding: negative feedback around the 6973s and their transformer. The drawing prints R120 here, the same number as V105a’s plate resistor.
- R129, 2.7 kΩ
- R129, 2,700 Ω 1 W 5 %, from V106b’s cathode to the other end of the feedback winding.
- R134, 560 Ω
- R134, 1 W, loads one end of the feedback winding to ground. The drawing prints 860, not a standard value. It’s read as 560, the same as R135.
- R135, 560 Ω
- R135, 560 Ω 1 W, loads the other end.
- C107, 100 nF
- C107, .1 µF 600 V, from V106a’s plate to V107’s grid.
- C108, 100 nF
- C108, .1 µF 600 V, from V106b’s plate to V108’s grid.
- R130, 150 kΩ
- R130, 150 k, V107’s grid resistor, returned to the bias supply’s third line, −13.75 V (the drawing prints −13 to −14.5 V there), so the 6973 idles at about 13 mA with its grid held well negative.
- R131, 150 kΩ
- R131, 150 k, V108’s grid resistor, to the same line.
- V107, 6973
- A 6973 beam power tube, one side of the sidechain’s push-pull output stage. It drives T104, whose secondary the bridge rectifies into the control voltage.
- V108, 6973
- The other 6973, in opposite phase.
- R132, 560 Ω
- R132, 560 Ω, V107’s screen resistor.
- R133, 560 Ω
- R133, 560 Ω, V108’s screen resistor.
- R143, 47 kΩ
- R143, 47 k, with C105 from V107’s plate back to its own grid: it cuts V107’s gain at the very top so the sidechain stays stable.
- C105, 20 pF
- C105, 20 pF 1.6 kV, in series with R143.
- R144, 47 kΩ
- R144, 47 k, with C106 from V108’s plate to its grid (printed V144 and C107 on the drawing).
- C106, 20 pF
- C106, 20 pF 1.6 kV, in series with R144.
- T104 pri A, 5 H
- T104’s primary, V107’s half, from BL to the center on the raw line. With the other half, 10 kΩ plate to plate (typical, as the 660’s).
- T104 pri B, 5 H
- T104’s primary, V108’s half, from the center to BR.
- T104 sec, 1.25 H
- T104’s secondary, a quarter of the primary’s turns, into the bridge.
- T104 fb, 222 mH
- T104’s feedback winding, about a tenth of the primary’s turns (9.5:1), back to V106’s cathodes.
- T104 k, coupling factor 0.9990
- Coupling between T104’s two primary halves.
- T104 k, coupling factor 0.9990
- Coupling between T104’s primary and secondary. Below 1, the part that misses acts as leakage inductance.
- T104 k, coupling factor 0.9990
- Coupling between T104’s other primary half and the secondary.
- T104 k, coupling factor 0.9990
- Coupling between T104’s primary and its feedback winding.
- T104 k, coupling factor 0.9990
- Coupling between T104’s other primary half and the feedback winding.
- T104 k, coupling factor 0.9990
- Coupling between T104’s secondary and its feedback winding.
- R136, 3.9 kΩ
- R136, 3,900 Ω 1 W, across T104’s secondary (printed A136).
- CR101, 1N4001
- One diode of the bridge, a 1N538 rectifier. The bridge’s plus corner sits on the bias line, not ground, so the bridge’s minus pulls the control line further negative from the bias on both halves of the wave.
- CR102, 1N4001
- The bridge’s second diode to the plus corner.
- CR103, 1N4001
- One of the bridge’s two diodes to its minus corner, the control line.
- CR104, 1N4001
- The other diode to the control line.
- C109, 2 µF
- C109, 2 µF 200 V, holds the control voltage in every position of S102, from the control line to the bias line.
- R137, 220 kΩ
- R137, 220 k, lets the control line go back to the bias in every position.
- R141, 68 kΩ
- R141, 68 k, on the control line in position 1 only: about 0.1 s.
- R138, 470 kΩ
- R138, 470 k, on the control line in position 2: about 0.3 s.
- C113, 2 µF
- C113, 2 µF 200 V, joins C109 in positions 3 to 5.
- C111, 4 µF
- C111, 4 µF 150 V, joins in position 4.
- R139, 100 kΩ
- R139, 100 k, in series with C110 in positions 5 and 6. C110 charges only on a long run of loud playing, then holds the release back.
- C110, 8 µF
- C110, 8 µF 150 V, the slower time constant of positions 5 and 6.
- R140, 100 kΩ
- R140, 100 k, in series with C112 in position 6.
- C112, 20 µF
- C112, 20 µF 150 V, the slowest time constant, position 6 only.
- Zero, 2.5 kΩ pot, linear taper
- R142, Zero, 2,500 Ω from the bias supply’s −18.8 V line to ground, a front-panel screwdriver control. Its wiper is the bias for all eight 6386 grids, through the control line, about −7 V here. The manual sets it so the meter reads zero at rest. Taper assumed linear.
- C115, 100 nF
- C115, .1 µF 200 V, on the bias line.
- Bias supply, -35 V
- Stands in for the bias supply’s transformer T301 and bridge GR301 as a steady −34.9 V, the raw bias ahead of the choke. The drawing prints no voltage here. It’s set so the 6973s’ grid line, through R301 and R302, sits at −13.75 V, the middle of the −13 to −14.5 V the drawing prints on that line. C302 is rated 50 V.
- C302, 250 µF electrolytic
- C302, 250 µF 50 V, on the raw bias, ahead of the choke. The raw bias fans out two ways from here: through L302 to the Balance controls, and through R301 and R302 to the Zero controls and the 6973 grids.
- L302, 1 H
- L302, the bias supply’s choke. Its inductance isn’t printed, so it’s 1 H, a typical value.
- L302 R, 54.7 Ω
- L302’s winding resistance, 54.7 Ω, a fitted value, not on the drawing. With both channels’ Balance controls drawing about 0.45 A through it, it drops the raw bias to about −10 V on C303, under that capacitor’s 15 V rating.
- C303, 1 mF electrolytic
- C303, 1,000 µF 15 V, after the choke L302, on the line that feeds the Balance controls (about −10 V).
- R301, 1 kΩ
- R301, 1 k 1 W, from the raw bias, ahead of the choke, to the line that feeds the two channels’ Zero controls (about −18.8 V).
- C306, 250 µF electrolytic
- The 250 µF 50 V filter capacitor after R301 (printed C108 on the drawing, the same number as a coupling capacitor in the sidechain).
- R242, 2.5 kΩ
- R242, 2,500 Ω: the other channel’s Zero control, a load on the same line.
- R302, 10 kΩ
- R302, 10 k 5 %, to the line that biases the 6973s.
- C308, 25 µF electrolytic
- C308, 25 µF 25 V, on the 6973s’ bias line.
- R303, 27 kΩ
- R303, 27 k 5 %, the bias line’s bleeder.
- Regulated line, 240 V
- Stands in for the regulator (an EL34 pass tube, a 6084 error amplifier and a 5651 reference) as a steady 240 V, the voltage the drawing and the manual list for the EL34’s cathode.
- C307A, 80 µF electrolytic
- C307A, 80 µF 450 V, on the regulated line.
- Raw line, 449 V
- Stands in for the GZ34 rectifier and L301 as a steady source behind 200 Ω, so the raw line sits at about 435 V with both channels’ load on it. The drawing prints 420 to 450 V for this line, the regulator’s input.
- C305, C306, 70 µF electrolytic
- C305 and C306, 140 µF 350 V each, in series on the raw line, so they act as 70 µF.
- R315, 27 kΩ
- R315, 27 k 1 W, from the regulated line to the lower rail for the 6973s’ screens.
- R316, 100 kΩ
- R316, 100 k 1 W, the lower rail’s bleeder.
- C307B, 60 µF electrolytic
- C307B, 60 µF 350 V, on the lower rail.
- Ch. 2 Balance, 44.6 Ω
- Not a part: the other channel’s Balance controls (R205A, R205B) at rest, as the load they put on the line after the choke, about 0.22 A. They carry the same current as this channel’s.
- Ch. 2 screens, 142 kΩ
- Not a part: the other channel’s two 6973 screens at rest, as the load they put on the lower rail, about 1 mA.
- Ch. 2 plates, 12.8 kΩ
- Not a part: the other channel’s 6973s and V206 at rest, as the load they put on the raw line, about 34 mA.
About this version
- One channel, as drawn
- One channel of the factory drawing, with the mode switch at Left-Right (two separate limiters), fed unbalanced and loaded with 600 Ω.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.