Tube oil can echo with two writing brushes, 1969 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Tel-Ray Ad-n-Echo (Model 1001).
A tube echo on a disc turning in oil, after the Tel-Ray Ad-n-Echo. The guitar goes onto the disc as electric charge at a writing brush and comes off at a reading brush half a turn later. A selector switches in one of two writing brushes, or both, for two echo times. Reverb sends the echo back to the record side for repeats.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The pentode half of a 7199 is the record amp. A trim, Screen, sets its screen voltage, and with it the gain. Its plate drives the writing brushes through 100 k, with two zeners to ground that stop the swing near ±5 V. Each brush is fed from the wiper of its own preset, so the presets set each echo’s level. The disc carries the charge round in oil to the reading brush, where the triode half, a cathode follower behind 250 pF, picks it up. Its output goes to Echo Vol and the output, and through the Reverb pot back into the pentode’s cathode, so each echo is recorded again. The dry guitar comes from the pentode’s plate through 2.2 M and Direct Level.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 47k, 47 kΩ
- Input 1’s resistor, 47 k.
- 47k, 47 kΩ
- Input 2’s resistor, 47 k. Input 2’s jack joins its tip to input 1 while nothing is plugged in, so with one guitar in input 1 this is in parallel with input 1’s 47 k.
- .01µ, 10 nF
- Coupling cap into the pentode, .01 µF.
- 680k, 680 kΩ
- The pentode’s grid resistor, 680 k.
- V1, 7199 pentode (RCA sheet)
- The pentode half of the 7199, the record amp. It drives the writing brushes.
- 680, 680 Ω
- The pentode’s cathode resistor, 680 Ω. It has no bypass cap, because the echo comes into the cathode here, through Reverb.
- 470k, 470 kΩ
- The pentode’s plate resistor, 470 k.
- 470k, 470 kΩ
- From B to the top of Screen, 470 k.
- Screen, 500 kΩ pot, linear taper
- Screen, 500 k, here a trim inside (assumed). Its wiper sets the pentode’s screen voltage, from 0 to about 80 V. More screen voltage means more current and more gain, so this trim sets the record level and how far Reverb can go before the repeats run away. The pentode passes almost nothing below about 8 V on its screen, so the useful range is the lower fifth of its turn. Set at 0.2 (assumed), which puts about 13 V on the screen and 104 V on the plate.
- .047µ, 47 nF
- The screen’s bypass cap, .047 µF 400 V.
- .1µ, 100 nF
- From the pentode’s cathode to Reverb’s wiper, 0.1 µF 100 V.
- Reverb, 7.5 kΩ pot, linear taper
- Reverb, 7.5 k, linear taper (assumed). It sets how much of the echo goes back into the pentode’s cathode to be recorded again, so it sets the repeats.
- 1µ, 1 µF electrolytic
- From the triode’s cathode to Reverb, 1 µF 25 V.
- .01µ, 10 nF
- Coupling cap out of the pentode, .01 µF.
- 100k, 100 kΩ
- From the pentode to the drive line, 100 k. With it in series, the zeners can clamp the line.
- Zeners, 4.7 V zener pair, one direction, one each way
- Two zeners back to back from the drive line to ground. The drawing marks them “Zeners?” with no voltage. Here 4.7 V (assumed), so the drive line stops near ±5.4 V.
- 2.2M, 2.2 MΩ
- From the pentode to Direct Level, 2.2 M. This is the dry guitar’s path.
- Direct Level, 500 kΩ pot, audio taper
- Direct Level, 500 k, audio taper (assumed). It sets how much dry guitar reaches the output.
- 22k, 22 kΩ
- From Direct Level’s wiper to the output, 22 k.
- 1M, 1 MΩ
- The selector’s third pole puts this 1 M from the drive line to ground in the Both position. The drawing marks it “may not be present on all models”.
- Echo 1 Preset, 2 MΩ pot, linear taper
- Echo 1’s preset, 2 M, a trim inside. Its wiper feeds the first writing brush, so it sets that echo’s level. The drawing says it may be anything from 1 M to 7 M. Set at 0.15 (assumed), so the repeats run away only near the top of Reverb’s turn.
- Echo 2 Preset, 5 MΩ pot, linear taper
- Echo 2’s preset, 5 M, a trim inside, for the second writing brush. Set at half (assumed). Its wiper feeds the brush through more resistance than Echo 1’s does, so Echo 2 comes back darker and about 8 dB quieter at 1 kHz.
- Oil can, Oil can (Ad-n-Echo disc, typical)
- The can. It is a disc turning in oil, with two writing brushes and a reading brush. The disc turns once every 300 ms. The reading brush is half a turn after Echo 1’s brush (150 ms) and three quarters of a turn after Echo 2’s (225 ms). The charge left on the disc comes round again, weaker each turn. Every disc figure is assumed and can be changed.
- Motor, 10 V
- A stand-in that is not a part of the unit. It puts 10 V across Motor Speed, so the knob can set how fast the disc turns.
- Motor Speed, 10 kΩ pot, linear taper
- Motor Speed, a stand-in for the motor’s speed, not a control on the unit. At half Echo 1 comes back 150 ms after the note and Echo 2 225 ms. At 0 the disc turns a fifth slower (188 and 281 ms), full up a fifth faster (125 and 188 ms). The motor needs about half a second to reach a new speed, so the pitch swoops as it gets there.
- 250p, 250 pF
- From the reading brush to the triode’s grid, 250 pF.
- 4.7M, 4.7 MΩ
- The triode’s grid resistor, 4.7 M. With the 250 pF it cuts below about 135 Hz.
- V2, 7199 (triode section)
- The triode half of the 7199, a cathode follower. It reads the brush without loading it.
- 10k, 10 kΩ
- The triode’s cathode resistor, 10 k.
- .047µ, 47 nF
- From the triode’s cathode to Echo Vol, .047 µF.
- Echo Vol, 6 kΩ pot, linear taper
- Echo Vol, 6 k, linear taper (assumed). It sets how much echo reaches the output. Reverb is fed from before it, so Echo Vol doesn’t change the repeats.
- 47k, 47 kΩ
- From Echo Vol’s wiper to the output, 47 k.
- T, 125 V ac, 60 Hz
- The transformer’s secondary, as a sine at the mains frequency. Its voltage isn’t on the drawing, and 125 V is typical.
- T R, 50 Ω
- The winding’s resistance. A typical value.
- D1, 1N4001
- One of the two rectifiers in series, half wave. A silicon part stands in for the drawing’s rectifier.
- D2, 1N4001
- The second rectifier in series. Two share the reverse voltage.
- 30µ, 30 µF electrolytic
- First filter cap, 30 µF.
- 10k, 10 kΩ
- From the first filter cap to A, 10 k.
- 20µ, 20 µF electrolytic
- Filter cap on A, 20 µF. A feeds the triode’s plate.
- 10k, 10 kΩ
- From A to B, 10 k.
- 20µ, 20 µF electrolytic
- Filter cap on B, 20 µF. B feeds the pentode.
- 470k, 470 kΩ
- From B to the heater, 470 k. It lifts the heater’s DC voltage (C on the drawing). The heater isn’t modeled.
- .047µ, 47 nF
- The heater lift’s cap to ground, .047 µF 400 V.
About this version
- As drawn
- Jamie Ray’s drawing, rev 1.5. The winding, the zeners and the can’s figures are typical, not on the drawing.
Sources
- Jamie Ray, redrawn Ad-n-Echo (Model 1001) schematic, rev 1.5, 2006
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.