BBD chorus with a gated wet path, 1982 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Ibanez CS-9 Stereo Chorus.
A bucket-brigade chip delays the guitar a few milliseconds, a slow oscillator wobbles the delay, and the wobbling copy is mixed with the dry signal. A JFET mutes the delayed path between notes. Knobs Speed and Width. One of the two outputs.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC101A lifts the treble up to about 4.4 times above about 600 Hz before the delay, and the mixer cuts it back by the same amount. D101 and D102 catch peaks. Q102 and its parts make a two-pole low-pass near 7 kHz in front of the MN3207, and Q103 another near 6 kHz after it. The chip’s 1024 stages make a delay of 512 clock periods. R164 and the CLOCK trimmer feed the clock’s timing pin a steady current, for about 6.4 ms of delay. Q110 adds more through D108 when the LFO’s triangle is near its top, so at Width 7 the delay dips to about 2.6 ms once each sweep. Speed runs from about 0.3 to 3.4 sweeps a second. IC106 raises the dry signal about 4,300 times and charges C129 and C130 negative on every note. That turns Q104 off and lets the chorus through. About 33 ms after the playing stops, Q104 turns on again and mutes the delay chip’s hiss. The pedal’s second output, the dry signal minus the chorus, isn’t built. The clock’s scale, the CLOCK and BIAS trimmers’ settings and which parts run on 5 V are assumed.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C142, 100 µF electrolytic
- Across the 9 V supply.
- IC107, 5 V
- A 78L05 regulator, modeled as a steady 5 V source. It feeds the delay chip, its clock and the BIAS trimmer.
- C140, 100 µF electrolytic
- The 5 V line’s filter cap.
- R175, 10 kΩ
- Top of the 4.5 V bias divider.
- R176, 10 kΩ
- Bottom of the bias divider.
- C141, 47 µF electrolytic
- The bias line’s filter cap. It makes the line a quiet AC ground.
- R101, 1 kΩ
- In series with the input.
- C101, 47 nF
- Input coupling cap.
- R102, 510 kΩ
- Biases Q101 at 4.5 V. The guitar sees about 510 kΩ.
- Q101, 2SC536F
- A 2SC536 emitter follower, the input buffer.
- R103, 10 kΩ
- Q101’s emitter load.
- C102, 1 µF electrolytic
- Couples Q101 to IC101A.
- R104, 91 kΩ
- Into IC101A. With R106 the bass passes at a gain of one, inverted.
- C103, 2.2 nF
- In series with R105, beside R104. Above about 600 Hz it lets R105 in, so the treble is lifted ahead of the delay.
- R105, 27 kΩ
- With C103 it sets the treble lift, up to about 4.4 times.
- R106, 91 kΩ
- IC101A’s feedback.
- C104, 47 pF
- Across R106, for stability.
- R107, 47 kΩ
- Holds IC101A’s plus input at 4.5 V.
- IC101A, TL022
- Half a TL022, the input stage with the treble lift. Its output is the dry signal, and it feeds the delay and the gate.
- R108, 4.7 kΩ
- Into the limiter.
- D101, 1N914 / 1N4148
- With D102 back to back into C105, it catches peaks over about 0.6 V, so the delay chip isn’t pushed past its range. An MA150, a 1N914 stands in.
- D102, 1N914 / 1N4148
- The other half of the limiter.
- C105, 10 µF electrolytic
- Holds the limiter’s diodes at the signal’s DC level.
- R109, 10 kΩ
- First resistor of the filter in front of the delay.
- R110, 10 kΩ
- Second resistor of the filter.
- C106, 18 nF
- Feedback from Q102’s emitter. With C107 it makes a two-pole low-pass near 7 kHz, so the clock doesn’t mix with the guitar’s highs.
- C107, 270 pF
- The filter’s cap to ground.
- Q102, 2SC536F
- A 2SC536 emitter follower, the filter’s buffer.
- R111, 10 kΩ
- Q102’s emitter load.
- C108, 33 nF
- Couples the filter to the delay chip, so the BIAS trimmer alone sets its input’s DC.
- R114, 5.1 kΩ
- Top of the BIAS divider, from 5 V.
- VR102, 10 kΩ pot, linear taper
- The BIAS trimmer, 10 kΩ. It sets the delay chip’s input DC. Set at the middle, about 2.5 V, an assumed setting.
- R115, 5.1 kΩ
- Bottom of the BIAS divider.
- C109, 1 µF electrolytic
- Filters the BIAS wiper.
- R113, 100 kΩ
- Carries the bias to the delay chip’s input.
- IC102, MN3207
- MN3207 delay line, 1024 stages. It holds 512 samples and passes each on after 512 clock periods. The two outputs are drawn as one pin. On the 5 V line its clean range is about ±1 V around 2.5 V.
- IC103, MN3102
- MN3102 clock, drawn as its timing pin. The more current flows into it, the faster the clock and the shorter the delay. C135 is 47 pF. Q109, R162, R163 and D107 around its oscillator are inside this part.
- R116, 56 kΩ
- The delay chip’s output load.
- C111, 30 nF
- Couples the delay chip to the filter after it.
- R117, 680 kΩ
- Top of the filter’s bias divider.
- R118, 680 kΩ
- Bottom of the filter’s bias divider.
- R119, 10 kΩ
- Into the filter after the delay.
- C112, 2.7 nF
- A one-pole low-pass with R119, near 6 kHz.
- R120, 10 kΩ
- Into the two-pole filter.
- R121, 10 kΩ
- Second resistor of the two-pole filter.
- C113, 10 nF
- Feedback from Q103’s emitter. With C114 it makes a two-pole low-pass near 6 kHz that strips the clock off the delayed signal.
- C114, 680 pF
- The filter’s cap to ground.
- Q103, 2SC536F
- A 2SC536 emitter follower, the filter’s buffer.
- R122, 10 kΩ
- Q103’s emitter load.
- C115, 60 nF
- Couples Q103 to the gate.
- R123, 3.9 kΩ
- With Q104 it makes the gate: Q104 on shorts the wet line through this 3.9 kΩ.
- Q104, 2SK30A-GR
- A 2SK44, the 2SK30A preset stands in. With its gate at 0 V it conducts and mutes the delayed signal. A note pulls its gate negative, past pinch-off, and the chorus comes through.
- R124, 100 kΩ
- Holds the gated line at ground.
- C116, 60 nF
- Couples the gated line to the mixer.
- R125, 1 MΩ
- Holds the wet line at 4.5 V for Q105, the effect switch, drawn as a wire.
- C125, 100 nF
- Couples the dry signal to the gate’s amplifier.
- R143, 5.1 kΩ
- Into IC106.
- R144, 22 MΩ
- IC106’s feedback. The gain is about 4,300, so even a faint note drives it hard.
- C126, 30 pF
- Across R144. It trims the amplifier above about 240 Hz.
- R146, 10 kΩ
- Top of IC106’s bias divider.
- R147, 10 kΩ
- Bottom of IC106’s bias divider.
- C127, 10 µF electrolytic
- Filters IC106’s bias.
- R145, 5.1 kΩ
- IC106’s plus input to its bias.
- IC106, LM741 / µA741
- A µA741 with a gain of thousands, the gate’s detector amplifier.
- C128, 100 nF
- Couples IC106 to the rectifier.
- D106, 1N914 / 1N4148
- Holds the rectifier’s top near ground, so the swing sits below it.
- D105, 1N914 / 1N4148
- Passes the negative peaks to C129.
- C129, 33 nF
- Holds the negative peaks.
- R148, 10 kΩ
- From the peak holder to Q104’s gate.
- C130, 100 nF
- A tantalum cap on Q104’s gate. With R149 it sets how fast the gate closes after a note, about 33 ms.
- R149, 330 kΩ
- Pulls Q104’s gate back to 0 V between notes.
- R126, 82 kΩ
- The wet signal into the mixer.
- C117, 100 nF
- Couples the dry signal to the mixer.
- R127, 91 kΩ
- The dry signal into the mixer.
- R129, 91 kΩ
- The mixer’s feedback.
- C119, 47 pF
- Across R129, for stability.
- R130, 27 kΩ
- With C118 across the feedback it cuts the treble by as much as IC101A lifts it.
- C118, 2.2 nF
- In series with R130.
- R128, 33 kΩ
- Holds the mixer’s plus input at 4.5 V.
- IC101B, TL022
- Half a TL022, the mixer for output 1. It adds the dry and the wobbling delayed signal.
- R131, 470 Ω
- In series with the output.
- C120, 10 µF electrolytic
- Output coupling cap.
- R132, 100 kΩ
- Holds the output at ground.
- R164, 100 kΩ
- From 9 V toward the clock’s timing pin.
- VR101, 200 kΩ pot, linear taper
- The CLOCK trimmer, 200 kΩ, a variable resistor in series with R164. It sets the clock with the LFO at rest. Set at the middle, an assumed setting.
- Q110, 2SC536F
- A 2SC536 emitter follower on Width’s wiper.
- R167, 220 kΩ
- Width’s wiper into Q110.
- C136, 10 nF
- Smooths Q110’s base.
- R166, 2.4 kΩ
- From Q110 toward the clock.
- R165, 4.7 kΩ
- With R166, divides Q110’s emitter.
- D108, 1N914 / 1N4148
- Lets Q110 add current into the timing pin when the LFO is up. An MA150, a 1N914 stands in.
- R169, 10 kΩ
- Top of the LFO’s reference divider.
- R168, 10 kΩ
- Bottom of the LFO’s reference divider, 4.5 V.
- C137, 47 µF electrolytic
- The LFO reference’s filter cap.
- IC104B, TL022
- Half a TL022, an integrator. Its output ramps up and down, the triangle that wobbles the delay.
- C138, 100 nF
- The integrator’s cap. With R171 it sets how fast the triangle ramps.
- R171, 1 MΩ
- From Speed’s wiper into the integrator.
- Speed, 100 kΩ pot, linear taper
- Speed, 100 kΩ B. Its wiper takes a share of the square wave into the integrator. Up, more of the square reaches it and the triangle ramps faster.
- R170, 10 kΩ
- From the bottom of Speed to the LFO reference, so the slowest setting still moves.
- IC104A, TL022
- Half a TL022, a Schmitt trigger. It flips each time the triangle reaches a switch point.
- R172, 33 kΩ
- From the triangle to the trigger’s plus input.
- R173, 47 kΩ
- Positive feedback. With R172 it sets the triangle’s height, about 70 % of the square’s.
- C139, 10 nF
- From the output to the minus input.
- R174, 100 kΩ
- Holds the trigger’s minus input at the LFO reference.
- Width, 100 kΩ pot, linear taper
- Width, 100 kΩ B, across the triangle. It sets how much of the triangle moves the clock, so how far the delay wobbles.
About this version
- Stock
- The circuit as the factory drawing shows it, output 1. TL022 op-amps, a 741 for the gate, an MN3207 delay line and an MN3102 clock.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.