Four-quadrant multiplier ring modulator with a sine oscillator, 1970 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Maestro RM-1 Ring Modulator.
The first circuit on the bench that multiplies two signals. An MC1495, built here from its 16 transistors, multiplies the guitar by a sine from a 741 oscillator, so each note comes out as a sum and a difference frequency. A full-wave squelch shuts the output between notes.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC3 multiplies the guitar by the oscillator. Two sine waves multiplied make two new ones, at the sum and the difference of their frequencies. Neither of the originals is left. A 440 Hz A4 against a 1 kHz carrier comes out as 1440 Hz and 560 Hz. At IC3’s output, trimmed, each of those is about 42 dB over what’s left of the 1 kHz and 56 dB over what’s left of the 440 Hz. Every harmonic of the note makes a pair of its own. On the difference side the new tones move the opposite way to the note, so they don’t fall on the guitar’s harmonics. That’s the bell or clang sound. A low A2 at 110 Hz against a 420 Hz carrier comes out at 310 and 530 Hz. Inside IC3 the guitar on pin 4 splits the current of two diodes, and that sets how four transistors share the carrier’s current. The outputs are crossed, so with either input at 0 V the two sides cancel. The trims set how well they cancel. IC1b and IC2a make a squelch from the guitar’s level. Between notes T1 shorts the wet signal to ground, so no carrier leaks out. Modulation mixes dry and wet. Pitch sets the carrier, 230 Hz to 2.6 kHz in High and 21 to 240 Hz in Low. The model leaves out the external carrier, pitch pedal and modulation pedal jacks (with nothing plugged in), the OSC OUT jack and the power supply.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- −15 V, -15 V
- The −15 V rail for IC2b’s offset trim and the squelch trim. The power supply is not on the drawing, so it is a steady −15 V source here. The op-amps run on ±15 V.
- +12 V, 12 V
- The +12 V line for IC3’s loads and the null trims, a steady source here (the supply that makes it is not on the drawing).
- −12 V, -12 V
- The −12 V line under IC3’s current sources and the null trims. IC3’s pin 7 isn’t drawn connected, so it is assumed to go to −12 V here.
- C1, 330 nF
- Input coupling cap. With Audio Volume’s 50 kΩ it passes everything above about 10 Hz.
- Audio Volume, 50 kΩ pot, audio taper
- Audio Volume, 50 kΩ across the input, so it is also the input impedance. It sets how hard the guitar drives IC1a, the multiplier and the squelch. The taper isn’t marked, so it is set as audio taper.
- R1, 10 kΩ
- In series with IC1a’s + input. With C2 it rolls off above about 80 kHz.
- C2, 200 pF
- With R1, keeps radio frequencies out of IC1a.
- IC1a, MC1458
- Input amplifier, half a 1458, non-inverting. Its gain is 1 + R3/R2, 48 (34 dB). Its output is the dry signal, and it also feeds the multiplier and the squelch’s rectifier.
- R3, 47 kΩ
- IC1a’s feedback resistor. Against R2 it sets the gain of 48.
- R2, 1 kΩ
- IC1a’s gain leg to ground through C3.
- C3, 20 µF electrolytic
- Blocks DC in IC1a’s gain leg, so the stage has a gain of 1 at DC. The gain is down 3 dB at about 8 Hz.
- R4, 10 kΩ
- Feeds IC1a’s output to the rectifier’s summing point.
- IC1b, MC1458
- Half-wave rectifier, half a 1458. For a positive input its output pulls D2 down and R6 brings the point between R6 and R8 to minus the input. For a negative input D1 conducts and that point stays at 0 V.
- R5, 4.7 kΩ
- Ties IC1b’s + input to ground.
- D1, 1N914 / 1N4148
- Conducts when the input goes negative, so IC1b’s output can’t swing far and the rectified point stays at 0 V.
- D2, 1N914 / 1N4148
- Conducts when the input goes positive. The point between R6 and R8 then follows minus the input.
- R6, 10 kΩ
- IC1b’s feedback resistor, equal to R4, so the rectified half comes out at the same size.
- R8, 5.1 kΩ
- 5.1 kΩ, half of R7. The rectified half through R8 counts twice against the straight signal through R7, so the sum at IC2a is the full-wave rectified signal, every half of the wave pointing the same way.
- R7, 10 kΩ
- The straight signal into IC2a’s summing point. With R8 it makes the full-wave rectifier.
- TR1, 5 kΩ pot, linear taper
- Linear Squelch Adjust, a 5 kΩ trim from −15 V to ground. Through R9 it sets where the squelch rests. Set here at 0.15, so with no input the JFET’s gate rests at about 1.6 V, partly on.
- R9, 100 kΩ
- Brings the squelch trim’s voltage into IC2a’s summing point.
- IC2a, MC1458
- Squelch amplifier, half a 1458, inverting. Its gain on the rectified guitar is R11 divided by R7, about 10, and the trim’s offset is added. Its output goes up as the guitar gets louder.
- R10, 4.7 kΩ
- Ties IC2a’s + input to ground.
- R11, 100 kΩ
- IC2a’s feedback resistor, 100 kΩ.
- D3, 1N914 / 1N4148
- IC2a can charge C4 up through it but can’t pull C4 down.
- R12, 1 kΩ
- Charges C4 from D3. With C4 the squelch opens in about 20 ms.
- C4, 20 µF electrolytic
- Holds the squelch voltage on the JFET’s gate. R13 discharges it in about 0.2 s after a note stops.
- R13, 10 kΩ
- Discharges C4, so the squelch closes about 0.2 s after the guitar stops.
- T1, 2N4360
- The squelch, a 2N4360 P-channel JFET from IC2b’s input to ground. With the gate near 0 V it is a few hundred ohms against R27’s 47 kΩ, so the ring modulator’s output is cut about 40 dB between notes. Once the gate is over about 2.5 V it is off and the signal passes.
- IC4, LM741 / µA741
- The carrier oscillator, a 741 with a Wien bridge, a network of two resistors and two caps that sets the pitch. R41 and TR5 set its gain just over 3, and the zeners hold the swing at about ±5 V.
- R41, 4.7 kΩ
- IC4’s feedback resistor.
- TR5, 5 kΩ pot, linear taper
- Osc Adjust, a 5 kΩ trim as a variable resistor from IC4’s − input to ground. It sets IC4’s gain at 1 + R41 divided by the trim’s resistance. Here it is at 0.6, which is 2.0 kΩ and a gain of 3.35. With the trim below about 0.57 the oscillator stops at the bottom of Pitch.
- R42, 10 kΩ
- From the bridge’s middle to IC4’s + input.
- R43, 270 kΩ
- 270 kΩ from the bridge’s middle to ground. It loads the bridge a little at the low end of Pitch.
- C8, 15 nF
- The bridge’s series cap, 15 nF, always in.
- C7, 150 nF
- Pitch Range’s series cap. In Low it goes across C8, 0.165 µF in all, and the pitch drops about ten times.
- D4, D5, 3.3 V zener pair, one direction, one each way
- Two 1N746 3.3 V zeners back to back from the bridge to ground. They clip the swing there near ±4 V and hold the oscillator’s level steady. They also round the sine a little: its third harmonic is about 29 dB down at 1 kHz.
- R44, 4.7 kΩ
- 4.7 kΩ in series with the Pitch rheostat, so the bridge’s resistance never goes below 4.7 kΩ.
- Pitch, 50 kΩ pot, linear taper
- Pitch, one gang of a 50 kΩ dual pot as a variable resistor in the bridge’s series arm. Turned up, it removes resistance from both arms and the carrier goes up. The High range is about 230 Hz to 2.6 kHz and the Low range about 21 to 240 Hz. The taper isn’t marked, so it is set as linear.
- Pitch (gang), 50 kΩ pot, linear taper
- The other gang of Pitch, in the bridge’s grounded arm, so both arms change together.
- R45, 4.7 kΩ
- 4.7 kΩ in series with the second gang.
- C10, 15 nF
- The bridge’s grounded cap, 15 nF, always in.
- C9, 150 nF
- Pitch Range’s grounded cap, across C10 in Low.
- R46, 10 kΩ
- The top of the OSC OUT jack’s divider. The jack is left out, so with R47 it is a 14.7 kΩ load on IC4.
- R47, 4.7 kΩ
- The bottom of the OSC OUT divider.
- C6, 20 µF electrolytic
- Couples the carrier to IC3.
- R38, 47 kΩ
- Top of the carrier divider into IC3’s pin 9.
- R37, 47 kΩ
- Bottom of the carrier divider. Pin 9 gets half the oscillator, about 2.8 V peak.
- R40, 18 kΩ
- Top of the guitar’s divider into IC3’s pin 4.
- R39, 47 kΩ
- Bottom of the guitar’s divider. Pin 4 gets 0.72 of IC1a’s output.
- R36, 3.3 kΩ
- From +12 V to the top of the null trims.
- R32, 3.3 kΩ
- From the top of the null trims to ground. With R36 and the trims it holds the top near +3.2 V.
- R35, 4.7 kΩ
- In series with the carrier null trim, so the trim covers only about ±1.1 V.
- TR4, 5 kΩ pot, linear taper
- Carrier Null Adjust, 5 kΩ. It sets the DC on pin 8, the other side of the guitar’s input pair. Where pin 8 matches pin 4 the carrier can’t get through with no guitar. Set here at 0.478, which leaves 0.09 mV of carrier at IC3’s output, against 32 mV at 0.7.
- R34, 4.7 kΩ
- In series with the carrier null trim at its bottom.
- TR3, 5 kΩ pot, linear taper
- Signal Null Adjust, 5 kΩ across the ±3.2 V lines. It sets the DC on pin 12, the other side of the carrier’s input pair. Where pin 12 matches pin 9 the guitar can’t get through by itself. Set here at 0.494, which leaves a 440 Hz note about 56 dB under the new tones at IC3’s output.
- R33, 3.3 kΩ
- From −12 V to the bottom of the null trims.
- R31, 3.3 kΩ
- From the bottom of the null trims to ground, holding it near −3.2 V.
- R30, 10 kΩ
- Across pins 5 and 6, the guitar side’s emitters. The guitar’s voltage across it, divided by 10 kΩ, is the current it steers from one side to the other.
- R29, 10 kΩ
- Across pins 10 and 11, the carrier side’s emitters. It does the same for the carrier.
- R48, 4.7 kΩ
- From pins 3 and 13 to ground. It sets the current in IC3’s four current sources, about 1.14 mA each with pin 7 at −12 V.
- R24, 3.3 kΩ
- From +12 V to pin 1, the top of the linearizing diodes. They pull about 2.3 mA, so pin 1 sits near 4.5 V.
- R26, 3.3 kΩ
- Pin 2’s load from +12 V. The output current of Q6 and Q8 through it is the output voltage, near 8.3 V at rest.
- R25, 3.3 kΩ
- Pin 14’s load. Only pin 2 is used.
- Q1, 2N3904
- Y input, first half of the Darlington on pin 4 (the guitar). With its partner it steers the Y side’s current toward the left diode as pin 4 rises.
- Q1, 2N3904
- Y input, second half of the pin 4 Darlington. Its emitter is pin 5, one end of R30.
- 4k, 4 kΩ
- Inside the chip, 4.0 kΩ. It keeps a little current in the Darlington’s first half.
- Q2, 2N3904
- Y input, first half of the Darlington on pin 8, the carrier null trim’s side.
- Q2, 2N3904
- Second half of the pin 8 Darlington. Its emitter is pin 6, the other end of R30.
- 4k, 4 kΩ
- Inside the chip, 4.0 kΩ, as for Q1.
- Q9, 2N3904
- Current source under pin 5. It copies the current in the reference diode on pins 3 and 13.
- 500, 500 Ω
- Inside the chip, 500 Ω in the current source’s emitter.
- Q10, 2N3904
- Current source under pin 6. R30 joins the two sources, so the signal on pins 4 and 8 moves current from one side to the other through R30.
- 500, 500 Ω
- Inside the chip, 500 Ω in the current source’s emitter.
- Dref, 2N3904 base-emitter
- The Y side’s reference diode. R48 pulls current through it, and Q9 and Q10 copy that current.
- 500, 500 Ω
- Inside the chip, 500 Ω under the reference diode.
- Q3, 2N3904
- X input, first half of the Darlington on pin 9 (the carrier). Its collector current is the current Q5 and Q6 share.
- Q3, 2N3904
- Second half of the pin 9 Darlington. Its emitter is pin 10, one end of R29.
- 4k, 4 kΩ
- Inside the chip, 4.0 kΩ.
- Q4, 2N3904
- X input, first half of the Darlington on pin 12, the signal null trim’s side. Its collector current is the current Q7 and Q8 share.
- Q4, 2N3904
- Second half of the pin 12 Darlington. Its emitter is pin 11, the other end of R29.
- 4k, 4 kΩ
- Inside the chip, 4.0 kΩ.
- Q11, 2N3904
- Current source under pin 10.
- 500, 500 Ω
- Inside the chip, 500 Ω in the current source’s emitter.
- Q12, 2N3904
- Current source under pin 11.
- 500, 500 Ω
- Inside the chip, 500 Ω in the current source’s emitter.
- Dref, 2N3904 base-emitter
- The X side’s reference diode, on the same pin as the Y side’s (pins 3 and 13 are tied on the board).
- 500, 500 Ω
- Inside the chip, 500 Ω under the reference diode.
- DL, 2N3904 base-emitter
- Linearizing diode from pin 1, carrying Q1’s current. The voltage across it sets the bases of Q6 and Q7.
- DR, 2N3904 base-emitter
- Linearizing diode from pin 1, carrying Q2’s current. It sets the bases of Q5 and Q8. The difference between the two diodes follows the guitar.
- Q5, 2N3904
- Upper quad. Q5 and Q6 share the current the carrier sends through Q3, split by the guitar on the diodes.
- Q6, 2N3904
- Upper quad, Q5’s partner.
- Q7, 2N3904
- Upper quad. Q7 and Q8 share the current through Q4, split the same way, with their collectors crossed over to Q5 and Q6’s.
- Q8, 2N3904
- Upper quad, Q7’s partner. Pin 14 collects Q5 and Q7, pin 2 Q6 and Q8. Where the two sides cancel, neither input by itself reaches the output.
- C5, 20 µF electrolytic
- Couples pin 2 to the output side and blocks its 8.3 V.
- R28, 47 kΩ
- Holds C5’s far end at ground for DC.
- R27, 47 kΩ
- From C5 to IC2b’s input. With T1 on it is the top of the squelch’s divider.
- R22, 10 kΩ
- From +15 V to the offset trim.
- TR2, 5 kΩ pot, linear taper
- Offset Adjust, 5 kΩ between R22 and R23. Through R21 it nulls IC2b’s DC offset. The op-amps here have none, so it is set at the middle.
- R23, 10 kΩ
- From the offset trim to −15 V.
- R21, 2.7 MΩ
- 2.7 MΩ from the offset trim into IC2b’s input.
- IC2b, MC1458
- Output amplifier, half a 1458, non-inverting, gain 1 + R19/R20, 48 (34 dB). Its output is the wet signal.
- R20, 1 kΩ
- IC2b’s gain leg to ground.
- R19, 47 kΩ
- IC2b’s feedback resistor.
- R18, 47 kΩ
- Feeds the wet signal to the Modulation pot’s wet end.
- R14, 47 kΩ
- Feeds the dry signal from IC1a to the Modulation pot’s dry end.
- Modulation, 50 kΩ pot, linear taper
- Modulation, 50 kΩ linear with its wiper grounded. Turned up, it shorts more of the dry side and less of the wet side. At 0 only the dry guitar reaches the jack, at full only the ring modulator.
- R15, 47 kΩ
- From the dry end of Modulation to the output.
- R17, 47 kΩ
- From the wet end of Modulation to the output.
- R16, 47 kΩ
- Output resistor to ground. With R15 and R17 it mixes the two.
About this version
- Drawn
- The op-amps run on ±15 V and IC3 on ±12 V, steady sources here. The trims are set as a builder would set them. The two nulls are set for the least carrier and guitar at IC3’s output, and Osc Adjust is set so the oscillator runs at every Pitch setting.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.