FET studio limiter, 1973 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the UREI 1176LN Limiting Amplifier.
A FET across the signal works as a resistor the gain control circuit can turn down. The control circuit listens after the preamp, so the limiter works on its own result, and the ratio buttons change both how much it hears and where it starts.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar reaches the unit through a DI box at unity gain, which isn’t part of it. The input amp passes the signal on at a gain of 1, and Input sets how much of it reaches R6 and Q1. Q1 is a FET across the signal path. At rest its gate sits just past pinch-off, so it barely conducts. The preamp and line amp then raise the signal about 30 dB into a 600 Ω line, with Input and Output full. The factory lists 45 dB. T2 steps the line amp’s output up 1:2 to the 600 Ω line. The side chain is fed from the preamp’s output ahead of the Output knob, so Output sets the level without changing the limiting. The ratio buttons set how much of that signal reaches the control amp, and how far below the Q bias point its diodes sit. A peak big enough to turn the diodes on charges C27 through Attack. The control line rises, Q1’s resistance falls, and less of the signal reaches the preamp. Release sets how fast C27 discharges. The factory lists attack from 20 to 800 µs and release from 50 ms to 1.1 s. Input sets how far the signal goes over the threshold, so it sets how much limiting there is. The meter switch picks gain reduction or the output level. With the trims set as the factory sets them, the gain reduction meter reads within about half a dB up to 10 dB of reduction.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- −10 V, -10 V
- The −10 V rail. The unit makes it with a 10 V zener (CR6) from its own transformer, modeled as a steady source. It sets the Q bias and the threshold chain.
- R17, 6.8 kΩ
- Drops the +30 V rail for the preamp, about 25.8 V.
- C7, 100 µF electrolytic
- Filters the preamp’s rail.
- R70, 4.7 kΩ
- Drops the +30 V rail for the control amp’s collector loads, about 27.8 V.
- C18, 47 µF electrolytic
- Filters the control amp’s rail.
- DI in, 1 MΩ
- Not part of the unit: the DI box’s input resistance, 1 MΩ, as a guitar amp’s.
- DI box, 1 V
- Not part of the unit: a DI box at unity gain with a 50 Ω output. The unit’s 10 kΩ input would load a pickup and darken it, so the guitar meets the unit through this buffer.
- C30, 6.8 µF electrolytic
- Input coupling cap on the + terminal.
- R1-D, 10 kΩ
- IC2-B’s input resistor. With R1-C it sets a gain of −1, and it sets the + terminal’s input impedance at 10 kΩ.
- R1-C, 10 kΩ
- IC2-B’s feedback resistor.
- IC2-B, NE5532
- Inverts the + terminal’s signal, half a 5532 on the 30 V rail, biased at 15 V.
- C31, 6.8 µF electrolytic
- Input coupling cap on the COM terminal, grounded here (an unbalanced source).
- R1-E, 10 kΩ
- Feeds the COM terminal into IC2-A.
- R1-B, 10 kΩ
- Feeds IC2-B’s inverted signal into IC2-A.
- R1-A, 10 kΩ
- IC2-A’s feedback resistor. IC2-A sums the two inputs and inverts again, so its output is + minus COM at a gain of 1.
- C32, 220 pF
- Rolls IC2-A off above about 72 kHz.
- IC2-A, NE5532
- The balanced input’s summing stage, the other half of the 5532.
- R3, 100 kΩ
- Top of the input amp’s bias divider.
- R4, 100 kΩ
- Bottom of the bias divider: 15 V for both op-amps’ + inputs.
- C34, 47 µF electrolytic
- Filters the 15 V bias. Its value, 47 µF, is hard to read on the drawing.
- C33, 6.8 µF electrolytic
- Couples the input amp to the Input pot.
- Input, 10 kΩ pot, audio taper
- Input level, 10 kΩ. The drawing doesn’t show the taper, so it’s audio here. It sets how far the signal goes over the threshold, so it sets how much limiting there is.
- R6, 27 kΩ
- The series arm of the limiter’s L pad. Q1 is the shunt arm: as Q1’s resistance falls, less of the signal reaches the preamp.
- Q1, 2N5457 (low-current fit)
- The voltage-variable resistor: a 2N5457, the part early units used (later ones a selected BF245A). The model’s law includes the channel’s small current below pinch-off, where Q1 sits. At idle its gate is just past pinch-off. When the control line rises, the channel opens and shunts the signal.
- R8, 10 kΩ
- Ties Q1’s source to ground at DC.
- C2, 100 µF electrolytic
- Drives Q1’s source with half of Q2’s emitter signal, part of the circuit that keeps Q1’s distortion low.
- C5, 220 nF
- Takes the signal at the preamp’s feedback node, a copy of Q1’s drain signal from a low impedance.
- R9, 2.2 MΩ
- With R7, puts half of the drain signal on Q1’s gate. A FET channel with its gate at half the drain-source signal acts much more like a plain resistor.
- C4, 200 pF
- Across R9, so the gate keeps getting its half share in the highs, against the gate’s capacitance.
- R7, 2.2 MΩ
- Brings the control voltage to Q1’s gate, and is the other half of the gate’s divider.
- C3, 200 pF
- Across R7, the partner of C4.
- C27, 220 nF
- Holds the control voltage. The diodes charge it through Attack, and it discharges through Release.
- C1, 1 µF
- Couples Q1’s drain to the preamp.
- R10, 1 kΩ
- Base stopper for Q2.
- C6, 27 pF
- With R10, keeps radio frequencies off Q2’s base.
- Q2, BC107
- The preamp’s input transistor, run at about 25 µA for low noise.
- R12, 1 MΩ
- Q2’s collector load.
- R11, 560 kΩ
- DC feedback: biases Q2’s base from Q3’s emitter, so the three stages hold their own operating point.
- R13, 180 Ω
- Upper half of Q2’s emitter resistor.
- R14, 180 Ω
- Lower half of Q2’s emitter resistor. The joint feeds Q1’s source through C2.
- R15, 150 Ω
- Brings the feedback into Q2’s emitter.
- R16, 100 Ω pot, linear taper
- Linearity trim, 100 Ω. It sets the feedback node’s signal against Q2’s emitter, so it sets the share reaching Q1’s gate. The factory sets it for least distortion.
- R21, 7.5 kΩ
- Overall feedback from the preamp’s output. Against R13 and R14 it sets the preamp’s gain, about 27 dB.
- Q3, BC107
- The preamp’s second stage, a common-emitter amp.
- R18, 22 kΩ
- Q3’s collector load.
- R19, 82 Ω
- Q3’s unbypassed emitter resistor.
- R20, 1.8 kΩ
- Q3’s emitter resistor at DC.
- C8, 100 µF electrolytic
- Bypasses R20, and keeps the signal off R11.
- Q4, BC107
- Emitter follower, the preamp’s output.
- C9, 47 µF electrolytic
- Couples the preamp to the Output pot and the side chain.
- Output, 100 kΩ pot, audio taper
- Output level, 100 kΩ. The drawing doesn’t show the taper, so it’s audio here. It is after the side-chain pickup, so it doesn’t change the limiting.
- C10, 1 µF
- Couples the Output pot to the line amp.
- R28, 10 kΩ
- Feeds Q5’s bias from the rail.
- C11, 47 µF electrolytic
- Filters Q5’s bias.
- R29, 1 MΩ
- Upper bias resistor for Q5’s base.
- R30, 200 kΩ
- Lower bias resistor: about 5 V on Q5’s base, which sets the output’s DC level near half the rail.
- Q5, BC107
- The line amp’s input transistor. The feedback from the output goes to its emitter.
- R31, 68 kΩ
- Q5’s collector load.
- R32, 2 kΩ
- Q5’s emitter resistor. Against R34 it sets the DC level of the output.
- R33, 11 kΩ
- With C13, adds to R32 for the signal only.
- C13, 100 µF electrolytic
- Blocks DC from R33.
- R34, 4.3 kΩ
- Feedback from the output to Q5’s emitter. With R32 and R33 it sets the line amp’s gain, about 11 dB.
- Q6, 2N5087
- PNP, the first half of the Darlington driver.
- R35, 10 kΩ
- Keeps a little current in Q6.
- Q7, 2N5087
- PNP, the second half of the driver, about 6 mA. It swings the output transistors’ bases.
- R36, 100 Ω
- Q7’s emitter resistor.
- CR1, 1N4001
- 1N4003, one of the two diodes that bias the output pair just into conduction.
- CR2, 1N4001
- 1N4003, the second bias diode.
- R38, 1.2 kΩ
- Upper half of the driver’s load.
- R39, 1.2 kΩ
- Lower half of the driver’s load.
- C14, 22 µF electrolytic
- Bootstraps the driver’s load from the output, so its current stays steady as the output swings.
- C12, 10 pF
- Compensation: with R37 it keeps the line amp stable.
- R37, 1 kΩ
- In series with C12.
- C29, 47 pF
- Rolls off the far highs at Q9’s base.
- Q8, MPSA06
- NPN output transistor (MPSU05, BD517 beside it), pushes the output up.
- R40, 4.3 Ω
- Q8’s emitter resistor.
- Q9, 2N4125
- PNP output transistor (MPSU55, BD518 beside it), pulls the output down.
- R41, 4.3 Ω
- Q9’s emitter resistor.
- C15, 470 µF electrolytic
- Couples the line amp to the output transformer.
- Rpri, 14 Ω
- T2’s primary winding resistance. A typical value.
- Primary, 2 H
- T2’s primary inductance, 2 H, a typical value for the size. The dot marks the end that swings with the secondary’s dotted end.
- Secondary, 8 H
- T2’s secondary, four times the primary’s inductance, so T2 steps the voltage up 1:2, enough for the manual’s +24 dBm from the 30 V rail.
- T2, coupling factor 0.9999
- Coupling between T2’s windings. Below 1, the rest shows up as leakage inductance.
- Rsec, 60 Ω
- T2’s secondary winding resistance. A typical value.
- R84, 1 kΩ
- Loads the secondary, so the transformer sees a load with nothing plugged in.
- Line, 600 Ω
- Not part of the unit: the 600 Ω line it drives.
- R26, 56 kΩ
- Feeds the preamp’s output, above the Output pot, into the ratio chain.
- R25, 68 kΩ
- Ratio chain. 20:1 picks up the signal at its top.
- R24, 56 kΩ
- Ratio chain. 12:1 picks up the signal at its top.
- R2, 56 kΩ
- Ratio chain. 8:1 picks up the signal at its top.
- R23, 47 kΩ
- Bottom of the ratio chain. 4:1 picks up the signal at its top, about a sixth of the preamp’s output.
- C17, 1 µF
- Couples the side chain into the control amp.
- Q12, BC107
- The control amp’s input stage.
- R60, 1 MΩ
- Biases Q12 from its own collector.
- R61, 470 kΩ
- Lower bias resistor for Q12.
- R62, 47 kΩ
- Q12’s collector load.
- R63, 4.7 kΩ
- Q12’s emitter resistor, returned to the R64 and R65 joint.
- R68, 47 kΩ
- Overall feedback from Q15’s emitter to Q12’s emitter.
- Q13, BC107
- Emitter follower after Q12. It drives CR4 and the next stage.
- R64, 2.4 kΩ
- Q13’s emitter load, upper half.
- R65, 270 Ω
- Q13’s emitter load, lower half.
- R66, 182 kΩ
- Feeds Q13’s output to Q14 and sets Q14’s bias (1 %).
- R67, 38.3 kΩ
- Lower bias resistor for Q14 (1 %).
- Q14, BC107
- Phase inverter: its output is opposite in phase to Q13’s.
- R69, 44.2 kΩ
- Q14’s collector load (1 %).
- R71, 7.68 kΩ
- Q14’s emitter resistor (1 %).
- Q15, BC107
- Emitter follower after Q14. It drives CR3.
- R72, 2.4 kΩ
- Q15’s emitter load, upper half.
- R73, 180 Ω
- Q15’s emitter load, lower half.
- C19, 6.8 µF electrolytic
- Couples Q15’s output to CR3.
- C20, 6.8 µF electrolytic
- Couples Q13’s output, opposite in phase, to CR4.
- R74, 47 kΩ
- Biases CR3’s anode from the A bus.
- R75, 47 kΩ
- Biases CR4’s anode from the A bus.
- C21, 100 µF electrolytic
- Holds the A bus steady.
- CR3, 1N914 / 1N4148
- FD333, rectifies one half of the wave.
- CR4, 1N914 / 1N4148
- FD333, rectifies the other half.
- Attack, 25 kΩ pot, linear taper
- Attack, 25 kΩ. The drawing doesn’t show the taper, so it’s linear here. Turned up, less of it sits between the diodes and C27, so C27 charges faster. Fully counterclockwise its switch, S9, turns the limiting off.
- R76, 470 Ω
- Across the Attack pot’s diode side.
- C22, 22 nF
- With R76, lets the first edge of a peak through quickly.
- Release, 5 MΩ pot, linear taper
- Release, 5 MΩ. The drawing doesn’t show the taper, so it’s linear here. C27 discharges through it to the Q bias point: about 1.1 s fully counterclockwise, 56 ms fully clockwise.
- R79, 270 kΩ
- From the Release wiper to its bottom, so the fastest release stops near 50 ms.
- R82, 10 kΩ
- From −10 V into the Q bias divider.
- R83, 3.9 kΩ
- Bottom of the Q bias divider.
- Q bias, 2 kΩ pot, linear taper
- Q bias trim, 2 kΩ. It sets Q1’s gate at rest. The manual sets it so Q1 just starts to conduct: 1 dB of loss with limiting off.
- R87, 150 Ω
- Top of the threshold chain.
- R46, 10 MΩ
- Keeps the A bus near the chain’s top when no tap is picked.
- R42, 470 Ω
- Threshold chain, 4:1 to 8:1.
- R43, 560 Ω
- Threshold chain, 8:1 to 12:1.
- R44, 1.5 kΩ
- Threshold chain, 12:1 to 20:1.
- R45, 2.2 kΩ
- Bottom of the threshold chain, to −10 V. The further down the chain the A bus is tapped, the further below the Q bias point the diodes sit, and the bigger a peak has to be before they conduct.
- R48, 3.9 MΩ
- Feeds the control voltage to Q10’s gate. At 3.9 MΩ it puts almost no load on C27.
- Q10, 2N5457 (low-current fit)
- A 2N5457 (a BF245A on later units), a source follower. Its source follows the control voltage from a low impedance.
- R52, 10 kΩ
- Q10’s source load, to −10 V.
- R49, 2.4 kΩ
- Drops the +30 V rail for Q10 and IC1.
- C28, 100 nF
- Filters the meter amp’s rail.
- R53, 15 kΩ
- Across the first part of R54, so R54 sets the tracking over a narrower range.
- R54, 100 kΩ pot, linear taper
- Tracking trim, 100 kΩ, inside the unit. It sets how far the meter moves for a change on the control line. The manual sets it so the meter reads −10 when the output really drops 10 dB.
- R57, 470 kΩ
- Pulls IC1’s minus input toward −10 V, part of the offset that sets the meter’s rest point.
- R58, 100 kΩ
- IC1’s feedback, taken after CR11 so the diode’s drop is inside the loop.
- IC1, TL071
- TL071, the meter amp. It turns a rise on the control line into a fall in meter current. Its rails are −10 V and about 20 V behind R49.
- R56, 10 kΩ
- From −10 V to the bottom of the zero trim.
- R55, 2 kΩ pot, linear taper
- Meter zero, 2 kΩ, through a hole in the front panel. It sets IC1’s plus input between 0 and about −1.7 V, so it sets the meter at 0 with no limiting.
- CR11, 1N914 / 1N4148
- Lets IC1 push current into the meter only one way, so the needle can’t be driven backward.
- R59, 3.6 kΩ
- In series with the meter in the GR position, 3.6 kΩ, the same as R51.
- Meter, 3.9 kΩ
- The VU meter, as its coil and rectifier’s resistance, 3,900 Ω (a standard VU movement). Its needle follows the average current through it.
- R50, 8.2 kΩ
- Series resistor for the +8 position: 0 on the meter at +8 dBm out.
- R51, 3.6 kΩ
- Series resistor for the +4 position: 0 on the meter at +4 dBm out, the standard VU meter hookup.
About this version
- Stock (rev. K)
- The LN circuit with the 5532 balanced input, from serial suffix K. Fed unbalanced here, the COM terminal grounded.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.