Two-channel 7591 reverb amp with lamp tremolo, early 1960s style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Gibson GA-30RVT Invader.
Two 6EU7 channels, each with bass, mid, treble and loudness around two stages, mixed into a cathodyne and 12AU7 drivers that push two 7591s in fixed bias. Channel II has the springs and a tremolo, a lamp beside a photocell on its second grid.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each channel starts on one half of a 6EU7. The tone network after it splits the signal. The treble goes through a .001 Β΅F straight to the Loudness pot, and the bass goes around it through the 10 MΞ© Bass pot and a 68 kΞ©. After the Loudness pot, two 150 kΞ© with 500 pF across them and a .01 Β΅F to the Mid pot make a notch in the mids that the Mid pot fills in. The Treble pot sits around the second 6EU7 stage. Its wiper is on ground, one end goes to a .22 Β΅F on the cathode and the other to a .022 Β΅F on the plate, so turning it moves the stage from a treble cut at the plate to a treble boost at the cathode. The two channels meet through 330 kΞ© and 100 kΞ© and go to a 6EU7 cathodyne, then a 12AU7 a side, then two 7591s in fixed bias with no feedback. Channel II feeds the springs from its bass network, and the reverb comes back into that channelβs second stage. The tremolo works on channel II too. An oscillator swings the current through a small bulb, and a photocell beside the bulb pulls the second stageβs grid down as the bulb brightens. The bulb glows dimly even with the tremolo off.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R1, 68βkΞ©
- Input 1βs resistor, 68 kΞ©. With nothing in input 2 the two 68 kΞ© are in parallel, so input 1 reaches the channel through 34 kΞ©. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- R2, 68βkΞ©
- Input 2βs resistor, 68 kΞ©. With nothing in input 1 that jack grounds input 1βs tip, so the two 68 kΞ© make a divider and input 2 is about 6 dB quieter. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- R35, 68βkΞ©
- Input 1βs resistor, 68 kΞ©. With nothing in input 2 the two 68 kΞ© are in parallel, so input 1 reaches the channel through 34 kΞ©. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- R36, 68βkΞ©
- Input 2βs resistor, 68 kΞ©. With nothing in input 1 that jack grounds input 1βs tip, so the two 68 kΞ© make a divider and input 2 is about 6 dB quieter. Thereβs no 1 MΞ© on the jacks. The 470 kΞ© after the .0047 Β΅F is the load.
- .0047Β΅, 4.7βnF
- Input coupling cap, .0047 Β΅F. With the 470 kΞ© after it, it cuts below about 70 Hz.
- 470k, 470βkΞ©
- Grid resistor for the first stage.
- V1A, 6EU7
- One half of V1, a 6EU7, channel Iβs first stage.
- 100k, 100βkΞ©
- Plate resistor for V1A. The drawing reads +169 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V1A, +1.2 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V1Aβs cathode resistor, so the stage has its full gain.
- .01Β΅, 10βnF
- Coupling cap to the tone network, .01 Β΅F.
- .001Β΅, 1βnF
- The treble path, from the tone node straight to the Loudness pot. It passes treble and blocks most of the bass.
- Bass, 10βMΞ© pot, reverse audio taper
- Bass, 10 MΞ© reverse audio. It runs from the tone node to the bass pathβs 68 kΞ©. Its third lug isnβt connected, so itβs a variable resistor. Turned up, its resistance drops and more of the bass gets around the .001 Β΅F.
- 68k, 68βkΞ©
- From the Bass pot to the Loudness potβs top, the end of the bass path.
- 470k, 470βkΞ©
- From the bass path to ground. It sets how much the bass path is pulled down.
- Loudness, 500βkΞ© pot, audio taper
- Loudness, 500 kΞ© audio, the channelβs volume, from the tone network to ground. Its wiper feeds the mid network into the second stage.
- 150k, 150βkΞ©
- First half of the mid network into the second stage.
- 150k, 150βkΞ©
- Second half of the mid network, into the second stageβs grid.
- 500p, 500βpF
- Across both 150 kΞ©. It carries the treble past the mid network.
- .01Β΅, 10βnF
- From the middle of the two 150 kΞ© to the Mid pot. With the Mid pot at 0 it makes a notch in the mids, near 500 Hz.
- Mid, 250βkΞ© pot, audio taper
- Mid, 250 kΞ© audio, as a variable resistor from the .01 Β΅F to ground. Turned up, its resistance rises, the notch gets shallower and more mids get through.
- V2A, 6EU7
- One half of V2, a 6EU7, channel Iβs second stage.
- 100k, 100βkΞ©
- Plate resistor for V2A. The drawing reads +170 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V2A, +1.3 V on the drawing. It has no bypass of its own. The Treble pot sets how much the .22 Β΅F bypasses it.
- .22Β΅, 220βnF
- From V2Aβs cathode to one end of the Treble pot. With the Treble pot turned up it bypasses the cathode resistor for the treble, so the stage has more gain from a few hundred hertz up.
- Treble, 1βMΞ© pot, reverse audio taper
- Treble, 1 MΞ© reverse audio, its wiper on ground. Turned up, the wiper moves toward the cathodeβs .22 Β΅F, so that cap bypasses the cathode resistor and the treble rises. Turned down, it moves toward the .022 Β΅F from the plate, which then shunts the treble to ground.
- .022Β΅, 22βnF
- From V2Aβs plate to the other end of the Treble pot. With the Treble pot turned down it shunts the plateβs treble to ground.
- 330k, 330βkΞ©
- Mixing resistor from V2Aβs plate to the node where both channels meet, 330 kΞ©. Channel II goes through 100 kΞ©.
- .0047Β΅, 4.7βnF
- Input coupling cap, .0047 Β΅F. With the 470 kΞ© after it, it cuts below about 70 Hz.
- 470k, 470βkΞ©
- Grid resistor for the first stage.
- V1B, 6EU7
- One half of V1, a 6EU7, channel IIβs first stage.
- 100k, 100βkΞ©
- Plate resistor for V1B. The drawing reads +169 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V1B, +1.2 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V1Bβs cathode resistor, so the stage has its full gain.
- .047Β΅, 47βnF
- Coupling cap to the tone network, .047 Β΅F. Channel I has .01 Β΅F here, so channel II keeps more bass.
- .001Β΅, 1βnF
- The treble path, from the tone node straight to the Loudness pot. It passes treble and blocks most of the bass.
- Bass, 10βMΞ© pot, reverse audio taper
- Bass, 10 MΞ© reverse audio. It runs from the tone node to the bass pathβs 68 kΞ©, and its third lug goes to the Reverb potβs top. Turned up, its resistance drops and more of the bass gets around the .001 Β΅F.
- 68k, 68βkΞ©
- From the Bass pot to the Loudness potβs top, the end of the bass path.
- 220k, 220βkΞ©
- From the bass path to the Reverb pot, 220 kΞ©. Channel I has 470 kΞ© to ground here. The current through it and the Bass potβs third lug is what drives the reverb.
- .001Β΅, 1βnF
- From the Loudness potβs top to ground, on channel II only. It trims the highest treble.
- Loudness, 500βkΞ© pot, audio taper
- Loudness, 500 kΞ© audio, the channelβs volume, from the tone network to ground. Its wiper feeds the mid network into the second stage.
- 150k, 150βkΞ©
- First half of the mid network into the second stage.
- 150k, 150βkΞ©
- Second half of the mid network, into the second stageβs grid.
- 500p, 500βpF
- Across both 150 kΞ©. It carries the treble past the mid network.
- .01Β΅, 10βnF
- From the middle of the two 150 kΞ© to the Mid pot. With the Mid pot at 0 it makes a notch in the mids, near 500 Hz.
- Mid, 250βkΞ© pot, audio taper
- Mid, 250 kΞ© audio, as a variable resistor from the .01 Β΅F to ground. Turned up, its resistance rises, the notch gets shallower and more mids get through.
- V2B, 6EU7
- One half of V2, a 6EU7, channel IIβs second stage. The reverb comes in on its grid, and the tremoloβs photocell pulls its grid down.
- 100k, 100βkΞ©
- Plate resistor for V2B. The drawing reads +170 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V2B, +1.3 V on the drawing. It has no bypass of its own. The Treble pot sets how much the .22 Β΅F bypasses it.
- .22Β΅, 220βnF
- From V2Bβs cathode to one end of the Treble pot. With the Treble pot turned up it bypasses the cathode resistor for the treble, so the stage has more gain from a few hundred hertz up.
- Treble, 1βMΞ© pot, reverse audio taper
- Treble, 1 MΞ© reverse audio, its wiper on ground. Turned up, the wiper moves toward the cathodeβs .22 Β΅F, so that cap bypasses the cathode resistor and the treble rises. Turned down, it moves toward the .022 Β΅F from the plate, which then shunts the treble to ground.
- .022Β΅, 22βnF
- From V2Bβs plate to the other end of the Treble pot. With the Treble pot turned down it shunts the plateβs treble to ground.
- 100k, 100βkΞ©
- Mixing resistor from V2Bβs plate to the node where both channels meet, 100 kΞ©. Channel I goes through 330 kΞ©, so channel II comes through about 6 dB stronger.
- 500p, 500βpF
- From the mixing node to ground. With the 330 kΞ© and 100 kΞ© it trims the highest treble before the cathodyne.
- Reverb, 250βkΞ© pot, audio taper
- Reverb, 250 kΞ© audio, the ground end of channel IIβs bass network. The bass networkβs current runs through it, and its wiper is V8Aβs grid, so it sets how hard the springs are driven.
- V8A, 6EU7
- One half of V8, a 6EU7, the reverbβs first gain stage.
- 100k, 100βkΞ©
- Plate resistor for V8A, +165 V on the drawing.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V8A, +1.25 V on the drawing.
- .1Β΅, 100βnF
- Only .1 Β΅F across V8Aβs cathode resistor, so the stage has less gain below about 1 kHz and less bass reaches the springs.
- .0047Β΅, 4.7βnF
- Coupling cap to the reverb driver. Into 220 kΞ© it cuts below about 150 Hz.
- 220k, 220βkΞ©
- The reverb driverβs grid resistor.
- V7A, 12AU7 / ECC82
- One half of V7, a 12AU7, the reverb driver. Its cathode resistor isnβt bypassed. The drawing reads +9 V on it, about 7.5 mA.
- 1.2k, 1.2βkΞ©
- Cathode resistor for the reverb driver.
- T3, 25βkΞ© to 8βΞ©, 20βH primary, 50βmH leakage
- The reverb transformer, from the driverβs plate to the spring unit. The drawing reads 13 V across its primary, so its resistance is set at 1.7 kΞ©. Its other figures, 25 kΞ© into 8 Ξ©, are typical for the job.
- Unit in R, 800βmΞ©
- Resistance of the reverb unitβs input coil. The current through it drives the springs, which play from a measured tankβs impulse response, a recording of how the real springs ring after a click.
- Unit in L, 1.1βmH
- Inductance of the reverb unitβs input coil, a measured long tankβs figure.
- Unit out L, 350βmH
- The reverb unitβs output coil, 0.35 H, from V3Bβs grid to ground. The springs come back in series with it.
- Unit out R, 181βΞ©
- Resistance of the unitβs output coil, 181 Ξ©, a measured long tankβs figure.
- 220k, 220βkΞ©
- Grid resistor for the reverb recovery stage.
- .001Β΅, 1βnF
- From the recovery grid to ground. It trims the springsβ highest treble.
- V3B, 6EU7
- One half of V3, a 6EU7, the reverb recovery stage. V3A, the other half, is the cathodyne in the power amp.
- 100k, 100βkΞ©
- Plate resistor for V3B, +172 V on the drawing.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V3B, +1.25 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V3Bβs cathode resistor.
- .0047Β΅, 4.7βnF
- Coupling cap from the recovery stage.
- 1.5M, 1.5βMΞ©
- From the recovery stage into V2Bβs grid, where the reverb meets channel IIβs dry signal.
- 5k, 5βkΞ©
- From the +255 V node to the OA2. It carries the tremoloβs current and the OA2βs, about 21 mA.
- V9, OA2 regulator
- V9, an OA2 gas regulator tube. It holds the tremoloβs supply near 150 V, so the lampβs idle glow doesnβt move with the rest of the supply.
- 150k, 150βkΞ©
- Plate resistor for the oscillator, from the +150 V node. The drawing reads +110 V on the plate.
- V8B, 6EU7
- The other half of V8, the tremolo oscillator. Its cathode goes straight to ground.
- .022Β΅, 22βnF
- First cap of the oscillatorβs phase-shift ladder.
- 330k, 330βkΞ©
- The ladderβs first leg to ground.
- .022Β΅, 22βnF
- Second ladder cap.
- 150k, 150βkΞ©
- In series with the Frequency pot, the ladderβs second leg. It sets the top speed.
- Frequency, 1.5βMΞ© pot, reverse audio taper
- Frequency, 1.5 MΞ© reverse audio, as a variable resistor from the 150 kΞ© to the foot switch. Turned up, its resistance drops and the oscillator runs faster.
- .01Β΅, 10βnF
- Third ladder cap, into the grid. At one frequency the three caps and legs turn the plateβs swing upside down by the time it reaches the grid, so the stage oscillates at that frequency.
- 4.7M, 4.7βMΞ©
- Grid leak for the oscillator, and the ladderβs last leg. The drawing reads β0.2 V on the grid.
- .022Β΅, 22βnF
- Couples the oscillatorβs swing toward the Depth pot.
- 470k, 470βkΞ©
- In series with the Depth pot. With the pot it divides the oscillatorβs swing down.
- Depth, 250βkΞ© pot, audio taper
- Depth, 250 kΞ© audio, to ground. Its wiper is the lamp driverβs grid, so it sets how far the lampβs current swings.
- V7B, 12AU7 / ECC82
- The other half of V7, the lamp driver. Its plate current runs through the lamp, so the lamp brightens and dims with the oscillator.
- 500Ξ©, 500βΞ© pot, linear taper
- A 500 Ξ© wire-wound trim as a variable resistor in the lamp driverβs cathode. It sets the lampβs idle current. The drawing reads +3.2 V on the cathode. Its setting isnβt on the drawing, so itβs set near that voltage.
- Lamp, 24 V bulb, 18 mA
- The bulb in the photocell assembly LDR-1, from the +150 V node to the lamp driverβs plate. The drawing reads 10 V across it at idle. It glows dimly at idle and brightens as the driverβs current rises.
- Cell, Gibson LDR-500 cell
- The photocell in LDR-1, from V2Bβs grid to ground. Lit, its resistance drops and it pulls the grid down, so channel II and its reverb get quieter. Dark, itβs about 1 MΞ© and hardly loads the grid.
- .0047Β΅, 4.7βnF
- Coupling cap into the cathodyne.
- V9, 6EU7
- 6EU7, a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 100k, 100βkΞ©
- The cathodyneβs plate resistor, the output to tube B.
- 3.3k, 3.3βkΞ©
- The cathodyneβs bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 100k, 100βkΞ©
- The cathodyneβs cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470βkΞ©
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathodeβs high DC voltage. Itβs the gridβs only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ξ©.
- .01Β΅, 10βnF
- Coupling cap from the inverter to side Aβs driver.
- .01Β΅, 10βnF
- Coupling cap from the inverter to side Bβs driver.
- 2.7k, 2.7βkΞ©
- Side Aβs driver cathode resistor, 2.7k Ξ© to ground with no bypass cap. Each half has its own, so each stage has less gain and the two sides donβt act on each other.
- 2.7k, 2.7βkΞ©
- Side Bβs driver cathode resistor, the same.
- 470k, 470βkΞ©
- Grid leak for side Aβs driver, to ground.
- V12a, 12AU7 / ECC82
- 12AU7, side Aβs driver: a gain stage that raises the inverterβs signal about 9 times on its way to tube Aβs grids. The other half drives side B.
- 100k, 100βkΞ©
- The driverβs plate resistor, 100k Ξ© from the node for the drivers.
- .022Β΅, 22βnF
- Coupling cap from the driverβs plate to tube Aβs grids.
- 470k, 470βkΞ©
- Grid leak for side Bβs driver, to ground.
- V12b, 12AU7 / ECC82
- The other half of the 12AU7, side Bβs driver.
- 100k, 100βkΞ©
- The driverβs plate resistor, 100k Ξ© from the node for the drivers.
- .022Β΅, 22βnF
- Coupling cap from the driverβs plate to tube Bβs grids.
- 1.5k, 1.5βkΞ©
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current.
- 1.5k, 1.5βkΞ©
- Grid stopper for tube B.
- V10, 7591
- 7591A, tube A of the push-pull pair, cathode grounded, biased from the fixed bias supply.
- V11, 7591
- 7591A, tube B of the pair.
- 220k, 220βkΞ©
- Grid leak for tube A, returned to the bias supply. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. Thatβs blocking distortion.
- 220k, 220βkΞ©
- Grid leak for tube B.
- 1k, 1βkΞ©
- Screen resistor for tube A. It limits the screen current when the tube is driven hard.
- 1k, 1βkΞ©
- Screen resistor for tube B.
- 4 H, 4βH
- The choke from the reservoir cap to B+, as on the ampβs drawing. The output transformerβs center tap, the screens and everything after them hang past it, so all of their current runs through it. It passes DC with little drop. With the cap after it, it would filter ripple, but ripple isnβt modeled here. Typical of the part.
- 90, 90βΞ©
- The chokeβs winding resistance, typical. With the output tubesβ whole current through it, itβs most of the DC drop between the reservoir and B+.
- 40Β΅, 40βΒ΅F electrolytic
- Filter cap on B+ after the choke, where the output transformerβs center tap and the screens hang.
- 2.5k, 2.5βkΞ©
- Dropping resistor from the screen supply node to the node for the drivers, as on the Gibson GA-30RVT Invader drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the drivers. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 4.7k, 4.7βkΞ©
- Dropping resistor from the node for the drivers to the node for the cathodyne, as on the Gibson GA-30RVT Invader drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 10Β΅, 10βΒ΅F electrolytic
- Filter cap at the node for the cathodyne. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 4.7k, 4.7βkΞ©
- Dropping resistor from the node for the cathodyne to the node for the preamp, as on the Gibson GA-30RVT Invader drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 10Β΅, 10βΒ΅F electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 1.5k, 1.5βkΞ©
- Dropping resistor from the node for the drivers to the node for the reverb driver and the tremolo, as on the Gibson GA-30RVT Invader drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the reverb driver and the tremolo. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 6.6βkΞ© to 16βΞ©, 30βH primary, 12βmH leakage
- The output transformer, 6.6 kΞ© plate to plate into 16 Ξ©, center tap on B+ after the choke. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 315 V ac, 60 Hz
- One half of the power transformerβs high-voltage winding, 315 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 315 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 60βΞ©
- Resistance of one half of the winding, plus the primaryβs share. With the rectifierβs own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 60βΞ©
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 20Β΅, 20βΒ΅F electrolytic
- The reservoir cap. It feeds the choke, and past it the output transformerβs center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- PT, 315 V ac, 60 Hz
- The end of the high-voltage winding the bias comes off, 315 V ac, the same end as the rectifierβs first plate. Itβs drawn as its own source so the bias supplyβs average can be found. Keep it equal to the winding beside the rectifier.
- 330k, 330βkΞ©
- Series resistor into the bias rectifier, 330k Ξ©. Thereβs no bias tap, so the bias comes straight off the high-voltage winding, and this resistor drops most of it.
- Bias diode, 1N4001
- The bias rectifier, a silicon diode turned so the supply comes out negative.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap on the bias supply, its plus side to ground.
- 7.5k, 7.5βkΞ©
- Second resistor of the bias supply, 7.5k Ξ© to the bias line. With the cap after it, it filters the ripple a second time.
- 20Β΅, 20βΒ΅F electrolytic
- Second filter cap, on the bias line, its plus side to ground.
- 47k, 47βkΞ©
- From the bias line to ground, 47k Ξ©. With the 7.5k Ξ© and 330k Ξ© above it, it divides the supply down to the bias. Thereβs no bias pot, so change this resistor to change the bias. Bigger runs the tubes colder.
- Coil R, 17.4βΞ©
- Voice coil resistance, the floor of the speakerβs impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ξ© peak near 74 Hz on 8 Ξ©), scaled to the 16 Ξ© tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 512βΒ΅H
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 928βΒ΅H
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 28.6βΞ©
- Limits what Loss L adds to the treble rise.
- Loss L2, 4.26βmH
- A second step in the treble rise, with Loss R2 across it: a real voice coilβs losses keep climbing from a few hundred hertz.
- Loss R2, 4.38βΞ©
- Limits what Loss L2 adds.
- Tank R, 167βΞ©
- Height of the bass resonance, about 185 Ξ© in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 42.2βmH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 110βΒ΅F
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The 6EU7 model is fitted to the Tung-Sol reissue plate chart. The 12AU7s use the 12AU7 model. The photocell and its bulb are the benchβs Gibson LDR-500. The reverb transformer and unit are typical.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.