One-channel 7189 amp with reverb and tremolo, late 1960s style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Teisco Check Mate 20.
A 12AX7 stage, a James-style Bass and Treble network, a Volume and a second 12AX7 stage into a 12AU7 driver and cathodyne and two 7189As with feedback. A crystal reverb from jack 3 and a 6AV6 tremolo on the output grids.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar comes in through 100 kΩ, with 30 kΩ and the empty jacks’ 100 kΩ resistors to ground, so the first stage sees about a sixth of the signal. The first stage’s cathode has only .1 µF across it, so the stage has more gain in the treble than in the lows. The tone network is the James kind: the Bass pot sits between two caps and the Treble pot works off a 500 pF. The reverb takes the guitar from jack 3 straight from the jack, before the first stage, through two 12AX7 stages into the reverb unit’s crystal. It comes back through 150 kΩ and the Reverb pot into the Volume’s top. The tremolo oscillator’s swing goes to the output tubes’ grid return, so it moves their bias.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 100k, 100 kΩ
- Input resistor from jack 1.
- 100k, 100 kΩ
- Input resistor from jack 2. With no plug in, the jack grounds its end, so it loads the grid.
- 100k, 100 kΩ
- Input resistor from jack 3, the same.
- 30k, 30 kΩ
- From the grid to ground, 30 kΩ. With the input resistors it cuts the guitar’s signal before the first stage.
- V1a, 12AX7 / ECC83 / 7025
- Half of V1, a 12AX7, the first stage.
- 100k, 100 kΩ
- Plate resistor for V1a, from the preamp’s supply.
- 1k, 1 kΩ
- Cathode resistor for V1a.
- .1µ, 100 nF
- Across V1a’s cathode resistor, only .1 µF. It bypasses the resistor above about 1.6 kHz, so the stage has more gain in the treble.
- .05µ, 50 nF
- Coupling cap into the tone network.
- 500p, 500 pF
- Treble cap, 500 pF to the Treble pot’s top.
- Treble 1M, 1 MΩ pot, linear taper
- Treble, 1 MΩ. Its wiper is the network’s output. Turned up, the wiper nears the 500 pF and more treble gets through. Turned down, it nears the .002 µF to ground. Marked B, read as linear. Brighter clockwise is assumed.
- .002µ, 2 nF
- From the Treble pot’s bottom to ground.
- 100k, 100 kΩ
- Into the bass side of the network, 100 kΩ to the Bass pot’s top.
- Bass 1M, 1 MΩ pot, linear taper
- Bass, 1 MΩ, between the .001 µF and the .03 µF. Turned up, the wiper nears the top, the .03 µF passes the lows to the wiper and the .001 µF is shorted out. Marked B, read as linear. More bass clockwise is assumed.
- .001µ, 1 nF
- From the Bass pot’s top to its wiper.
- .03µ, 30 nF
- From the Bass pot’s bottom to its wiper.
- 5k, 5 kΩ
- The bottom of the bass side, 5 kΩ to ground.
- 100k, 100 kΩ
- From the Bass wiper to the network’s output, where the bass and treble sides mix.
- Vol 1M, 1 MΩ pot, linear taper
- Volume, 1 MΩ, marked B, read as linear. Its wiper is V1b’s grid.
- V1b, 12AX7 / ECC83 / 7025
- The other half of V1, the second stage. Its plate drives the power amp’s driver.
- 100k, 100 kΩ
- Plate resistor for V1b, from the preamp’s supply.
- 1k, 1 kΩ
- Cathode resistor for V1b.
- .05µ, 50 nF
- Across V1b’s cathode resistor, .05 µF. It bypasses the resistor above about 3 kHz.
- 500k, 500 kΩ
- From jack 3’s tip to the reverb’s first stage. The reverb only gets a signal from jack 3.
- 100k, 100 kΩ
- Grid resistor for V3a. With the 500 kΩ it cuts the drive to a sixth.
- V3a, 12AX7 / ECC83 / 7025
- Half of V3, a 12AX7, the reverb’s first stage.
- 1k, 1 kΩ
- Cathode resistor for V3a, not bypassed.
- 100k, 100 kΩ
- Plate resistor for V3a, from the preamp’s supply.
- .01µ, 10 nF
- Coupling cap to V3b.
- 500k, 500 kΩ
- Grid resistor for V3b.
- V3b, 12AX7 / ECC83 / 7025
- The other half of V3, the reverb driver.
- 1k, 1 kΩ
- Cathode resistor for V3b.
- 30µ, 30 µF electrolytic
- Bypass for V3b’s cathode.
- 50k, 50 kΩ
- Plate resistor for V3b, 50 kΩ from the driver’s supply.
- .01µ, 10 nF
- From the reverb driver’s plate to the unit’s input element.
- 1M, 1 MΩ
- Across the unit’s input, 1 MΩ to ground.
- Unit in, 1 nF
- The reverb unit’s input element, a crystal, from the drive to ground. Its capacitance, 1 nF, is typical, not on the drawing.
- 10M, 10 MΩ
- Not a real part: a 10 MΩ across the input element, so the current in it follows the element’s voltage. That current drives the springs, which are played back from a recording of how a measured tank rings.
- Unit out, 1 nF
- The reverb unit’s output element, a crystal. The springs’ signal comes out through its own capacitance, 1 nF, typical.
- Unit out L, 1 µH
- Not a real part: where the springs’ signal comes in, in series with the output element.
- Unit out R, 1 Ω
- Not a real part: the bottom of the output element’s leg. The springs’ level is assumed. It is set so the springs sit as far under a picked note as on the Silvertone 1484, which has a crystal unit too.
- 150k, 150 kΩ
- From the unit’s output to the Reverb pot’s wiper.
- Reverb 1M, 1 MΩ pot, linear taper
- Reverb, 1 MΩ, marked B, read as linear. The springs come in on its wiper and leave from its top lug. Turned down, the wiper nears ground and the track between wiper and top is in series, so little gets through.
- .005µ, 5 nF
- From the Reverb pot’s top to the Volume’s top, where the reverb joins the dry signal.
- V4, 6AV6
- V4, a 6AV6, the tremolo’s oscillator. A ladder of three caps from its plate back to its grid turns the plate’s swing round by half a cycle at a few hertz, so the stage oscillates there.
- 100k, 100 kΩ
- The oscillator’s plate resistor, from the screens’ node.
- 1k, 1 kΩ
- The oscillator’s cathode resistor.
- 30µ, 30 µF electrolytic
- Bypass for the oscillator’s cathode.
- .02µ, 20 nF
- First cap of the ladder, from the oscillator’s plate.
- 100k, 100 kΩ
- The ladder’s first leg, 100 kΩ, with the Speed pot under it.
- Speed 1M, 1 MΩ pot, reverse audio taper
- Speed, 1 MΩ, a variable resistor under the 100 kΩ. Turned up, there’s less track in the circuit and the oscillator runs faster. Marked B. A reverse taper is assumed here so it changes evenly as it turns, and faster clockwise.
- .02µ, 20 nF
- Second cap of the ladder.
- 500k, 500 kΩ
- The ladder’s second leg, to ground.
- .02µ, 20 nF
- Last cap of the ladder, into the oscillator’s grid.
- 1M, 1 MΩ
- The oscillator’s grid resistor, 1 MΩ to ground.
- .1µ, 100 nF
- Couples the oscillator’s swing to the Depth pot.
- 250k, 250 kΩ
- From the coupling cap to the Depth pot’s top.
- Depth 500k, 500 kΩ pot, linear taper
- Depth, 500 kΩ, marked B, read as linear. Its wiper is the output tubes’ grid return, so the swing on it moves their bias. Turned up, more of the swing reaches the grids. More clockwise is assumed.
- .05µ, 50 nF
- From the output tubes’ grid return to ground. It rounds the swing off and keeps the guitar’s signal off the return.
- .02µ, 20 nF
- Coupling cap into the driver. With the grid resistor it sets how low the power amp goes, around 80 Hz.
- V2a, 12AU7 / ECC82
- 12AU7 (ECC82), the driver. A cathodyne has no gain of its own, so this stage raises the preamp’s signal enough to drive the output tubes.
- 100k, 100 kΩ
- Grid resistor for the driver.
- 100k, 100 kΩ
- Plate resistor for the driver.
- 2k, 2 kΩ
- Cathode resistor for the driver. It sets the driver’s bias, a volt or so. It sits on the feedback leg, so the fed-back signal moves the driver’s cathode.
- .05µ, 50 nF
- Coupling cap from the driver to the cathodyne.
- V2b, 12AU7 / ECC82
- The cathodyne, or split-load inverter. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side.
- 30k, 30 kΩ
- The cathodyne’s plate resistor, the output to tube B.
- 1k, 1 kΩ
- The cathodyne’s bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 30k, 30 kΩ
- The cathodyne’s cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 500k, 500 kΩ
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathode’s high DC voltage.
- 3k, 3 kΩ
- The feedback resistor from the speaker. With the 100 Ω below it, it sends about 3 % of the speaker voltage back to the driver’s cathode, which lowers the gain, flattens the response and tightens the bass.
- 100, 100 Ω
- The bottom of the feedback loop, 100 Ω to ground under the driver’s cathode resistor. It isn’t bypassed, so the fed-back speaker voltage moves the cathode. The driver’s current runs through it too, so it’s kept small.
- .05µ, 50 nF
- Coupling cap to tube A’s grid.
- .05µ, 50 nF
- Coupling cap to tube B’s grid.
- 3k, 3 kΩ
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current.
- 3k, 3 kΩ
- Grid stopper for tube B.
- V5, EL84 / 6BQ5
- EL84, tube A of the push-pull pair, its cathode on the shared cathode resistor, so it biases itself.
- V6, EL84 / 6BQ5
- EL84, tube B of the pair.
- 250k, 250 kΩ
- Grid leak for tube A, returned with tube B’s to the tremolo’s Depth pot, so the oscillator swings both grids together. The bias comes from the cathode resistor. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 250k, 250 kΩ
- Grid leak for tube B.
- 130, 130 Ω
- The shared cathode resistor. Every output tube’s current runs through it and lifts the cathodes above the grids, and that’s the bias. Driven hard, the pair draws more current on average, so the cathodes climb and the tubes run colder, which softens the clipping.
- 100µ, 100 µF electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 5k, 5 kΩ
- Dropping resistor from B+ to the screens. It’s large, so the screens sit about 30 V below the plates and drop further when they draw more current on a hard note.
- 20µ, 20 µF electrolytic
- Filter cap on the screen supply.
- 10k, 10 kΩ
- Dropping resistor from the screen supply node to the node for the driver and inverter, as on the Teisco Check Mate 20 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 10µ, 10 µF electrolytic
- Filter cap at the node for the driver and inverter. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 50k, 50 kΩ
- Dropping resistor from the screen supply node to the node for the preamp, as on the Teisco Check Mate 20 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 20µ, 20 µF electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 8 kΩ to 8 Ω, 40 H primary, 10 mH leakage
- The output transformer, 8 kΩ plate to plate into 8 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 244 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 244 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 244 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 20 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 20 Ω
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 50µ, 50 µF electrolytic
- The reservoir cap. It feeds the output transformer’s center tap. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 8.69 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 8 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256 µH
- Voice coil inductance. It makes the impedance rise through the treble. The feedback holds the output steadier against that than it would be without feedback.
- Loss L, 464 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 2.19 Ω
- Limits what Loss L2 adds.
- Tank R, 83.7 Ω
- Height of the bass resonance, about 92 Ω in all at its peak. The feedback holds the output steadier against that than it would be without feedback.
- Tank L, 21.1 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- Values from the factory drawing. The 7189As use the EL84 model.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.