Op-amp overdrive with germanium diodes to ground, 1977 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Ibanez OD-855 Overdrive II.
An emitter follower, an op-amp stage with the Tone pot between its inputs, a second op-amp stage with the Distortion pot in its gain leg, then two germanium diodes to ground. One RC4558 for both stages.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The Tone pot runs from IC101Aβs plus input to its minus input, with 0.1 Β΅F and 680 Ξ© from its wiper to ground. Toward the minus end the wiper raises the stageβs treble gain. Toward the plus end it sends treble to ground ahead of the stage. At 3 kHz the two ends are about 26 dB apart, and at the middle the stageβs gain is near 1. IC101Bβs gain is 1 plus 100 kΞ© over the Distortion potβs resistance and 470 Ξ©, from about 3 at 0 to about 160 at 1 kHz at full. The 0.47 Β΅F in that leg keeps the bass gain lower. The two 1N60s after R111 hold the wave to about 0.2 V either way, and they clip softer than silicon. Thereβs no stage after the diodes to make up level, so the output is small. The model leaves out the bypass switching.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R133, 10βkΞ©
- Top of the 4.5 V reference divider.
- R134, 10βkΞ©
- Bottom of the reference divider.
- C120, 47βΒ΅F electrolytic
- Filters the 4.5 V reference.
- C101, 20βnF
- Input coupling cap.
- R101, 10βkΞ©
- Series resistor into Q101βs base.
- R102, 510βkΞ©
- Biases Q101βs base from the 4.5 V reference.
- Q101, 2SC1815
- Input buffer, an emitter follower.
- R103, 3βkΞ©
- Q101βs emitter resistor.
- C102, 1βΒ΅F
- Coupling cap, non-polarized.
- R104, 3βkΞ©
- Series resistor into IC101A. With the Tone potβs plus side it forms the treble cut.
- R106, 100βkΞ©
- Biases IC101Aβs plus input at 4.5 V.
- Tone, 20βkΞ© pot, s curve taper
- Tone, 20 kΞ©, from IC101Aβs plus input to its minus input. Toward the minus end the treble gain rises. Toward the plus end treble goes to ground ahead of the stage. An S-curve (G) taper, as the drawing marks it: it changes fastest near each end of its turn.
- C103, 100βnF electrolytic
- From the Tone wiper toward ground, a tantalum cap.
- R105, 680βΞ©
- In series with C103. It sets the most treble gain IC101A can have.
- IC101A, RC4558
- Tone stage, non-inverting. Its gain is 1 plus R107 over the path from its minus input to ground.
- R107, 3βkΞ©
- Feedback resistor of the tone stage.
- C104, 470βpF
- Across R107. It rolls the stageβs gain back to 1 above about 110 kHz.
- C105, 1βΒ΅F
- Coupling cap to the second stage, non-polarized.
- R108, 10βkΞ©
- Biases IC101Bβs plus input at 4.5 V.
- IC101B, RC4558
- Gain stage, non-inverting. Its gain is set by R109 over R110 and the Distortion pot.
- R109, 100βkΞ©
- Feedback resistor of the gain stage.
- C107, 20βpF
- Across R109. It trims the gain above about 80 kHz.
- R110, 470βΞ©
- Least resistance in the gain leg, so the gain never goes over about 210.
- C106, 470βnF electrolytic
- A tantalum cap in the gain leg. The stageβs gain falls to 1 at DC, and at full Distortion the full gain starts near 720 Hz.
- Distortion, 50βkΞ© pot, reverse audio taper
- Distortion, a 50 kΞ© reverse audio pot, its wiper and one end to ground. Turned up, its resistance falls and the gain rises.
- R111, 10βkΞ©
- Feeds the diodes and limits their current.
- C108, 47βΒ΅F electrolytic
- Coupling cap to the diodes, so they clip around 0 V.
- C109, 2βnF
- With R111, a treble cut at the diodes from about 8 kHz.
- D101, D102, 1N60 germanium, one each way
- Two 1N60 germanium diodes back to back to ground. They hold the wave to about 0.2 V either way.
- Level, 10βkΞ© pot, linear taper
- Level, a 10 kΞ© linear pot across the diodes. Its wiper feeds the output buffer.
- C110, 100βnF
- Coupling cap from the Level wiper.
- R112, 510βkΞ©
- Biases the effect pathβs JFET switch at 4.5 V. The switch is drawn as a wire.
- C111, 100βnF
- Coupling cap into the output buffer.
- R114, 510βkΞ©
- Biases the output bufferβs base at 4.5 V.
- Q103, 2SC1815
- Output buffer, an emitter follower.
- R115, 10βkΞ©
- Output buffer emitter resistor.
- R116, 100βΞ©
- Output series resistor.
- C112, 10βΒ΅F electrolytic
- Output coupling cap.
- R117, 10βkΞ©
- Output pulldown.
About this version
- OD-855
- Values from the factory drawing.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.