Variable-mu tube compressor, 1960 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Altec 436C Compressor Amplifier.
The first stage turns down as its grids go more negative. The 6BC8 is a variable-mu triode, so its gain falls smoothly instead of cutting off. A 6AL5 rectifies the output and sets that grid voltage, and push-pull stages keep the gain change out of the signal.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar reaches T1 through a DI box with a 14 dB pad, which isnβt part of the unit. T1βs secondary is split at its center tap, and the ganged Input pots feed the two halves to V1βs grids in opposite phase. The center tap carries the control voltage, about β0.5 V at rest. When the output swings past the threshold, the 6AL5 conducts and charges C4 negative through R12, which moves both grids down together. The 6BC8βs gain falls. Both halves move the same way, so the change cancels in the push-pull pair while the signal adds. V2 drives T2 into a 600 Ξ© line, about 42 dB of gain with Input full. Threshold sets how far positive the 6AL5βs cathodes sit. Fully counterclockwise, compression starts near 0 dBm out at about 2:1. Fully clockwise it starts near +16 dBm at about 4:1. The pull down takes about 30 ms, and Release sets how fast C4 lets go, 0.35 to 1.3 s.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- DI in, 1βMΞ©
- Not part of the unit: the DI boxβs input resistance, 1 MΞ©, as a guitar ampβs.
- DI box, 0 V
- Not part of the unit: a DI box with a 14 dB pad and a 50 Ξ© output. The unit has 42 dB of gain, so a guitar at its own level would come out near 10 V. The pad brings the picked note to about 2 V.
- T1, 15βkΞ© to 80βkΞ©, 220βH primary, 60βmH leakage
- The bridging input transformer, 15 kΞ© to 80 kΞ©, so the signal comes out 2.3 times larger across the whole secondary. Each half feeds one grid of V1, in opposite phase. The center tap carries the control voltage to both grids. Tap any piece of it to change its figures.
- Input, 50βkΞ© pot, audio taper
- Input gain, 50 k across one half of T1βs secondary, wiper to V1aβs grid. It sets how hard the signal drives the unit, so with the threshold fixed it sets how much it compresses. Taper assumed audio.
- Input (B), 50βkΞ© pot, audio taper
- The other half of the ganged Input control, across the other half of the secondary, wiper to V1bβs grid.
- V1a, 6BC8
- Half a 6BC8, a semiremote-cutoff triode. Its grid is wound unevenly, so as the control voltage goes more negative its gain falls smoothly instead of cutting off. This is the gain cell.
- V1b, 6BC8
- The other half of the 6BC8, driven in opposite phase. The control voltage moves both grids together, so the thump of the gain change cancels in the push-pull pair while the signal adds.
- R8, 34βΞ©
- R8, 34 Ξ© 1 %, under both cathodes. The meter reads the voltage across it: the current falls as the tube is turned down. The meter is left out here.
- R3, 47βkΞ©
- V1aβs plate resistor, 47 k 1 % from the 210 V line (65 V on the plate on the drawing, 285 V at 20 dB of compression).
- R4, 47βkΞ©
- V1bβs plate resistor, 47 k 1 %, matched to R3 so the two plates move together as the gain changes.
- C2, 22βnF
- C2, .022 Β΅F, from V1aβs plate to V2aβs grid.
- C3, 22βnF
- C3, .022 Β΅F, from V1bβs plate to V2bβs grid.
- R5, 1βMΞ©
- V2aβs grid resistor, 1 M.
- R6, 1βMΞ©
- V2bβs grid resistor, 1 M.
- V2a, 6CG7
- Half a 6CG7, one side of the push-pull output stage into T2.
- V2b, 6CG7
- The other half of the 6CG7, the other side of the output stage.
- R7, 220βΞ©
- R7, 220 Ξ© under both cathodes (2.3 V on the drawing). The same voltage is the bottom of the threshold range.
- T2, 23βkΞ© to 600βΞ©, 80βH primary, 60βmH leakage
- The output transformer, 23 kΞ© plate to plate into 600 Ξ©, its center tap on 152 V. Its two secondaries are in series here for 600 Ξ©. Tap any piece of it to change its figures.
- Line, 600βΞ©
- Not part of the unit: the 600 Ξ© line the manual says to load it with.
- C5, 22βnF
- C5, .022 Β΅F, from V2bβs plate to one 6AL5 cathode.
- C6, 22βnF
- C6, .022 Β΅F, from V2aβs plate to the other 6AL5 cathode. With C5 the detector sees both halves of the wave.
- R10, 220βkΞ©
- R10, 220 k, holds one 6AL5 cathode at the threshold voltage.
- R11, 220βkΞ©
- R11, 220 k, holds the other cathode at the threshold voltage.
- Threshold, 25βkΞ© pot, linear taper
- Threshold, a 25 k screwdriver control between V2βs cathodes (2.3 V) and R15 (20 V). It sets how far positive the 6AL5βs cathodes sit, so how big a swing on V2βs plates it takes before the diodes conduct. Fully counterclockwise compression starts near 0 dBm out at 2:1, clockwise near +16 dBm at 4:1. Taper assumed linear.
- R15, 270βkΞ©
- R15, 270 k from the 210 V line, the top of the threshold divider (20 V at its bottom on the drawing).
- V3a, 6AL5
- One diode of the 6AL5. When V2bβs plate swings down past the threshold, it conducts and pulls the control line negative.
- V3b, 6AL5
- The 6AL5βs other diode, for V2aβs half of the wave.
- R12, 33βkΞ©
- R12, 33 k between the 6AL5 and the control line. With C4 it sets the attack, about 50 ms in the manual.
- C4, 1βΒ΅F
- C4, 1 Β΅F, holds the control voltage between peaks.
- R9, 270βkΞ©
- R9, 270 k, the fixed part of the release path. C4 lets go through R12, R9 and Release.
- Release, 1βMΞ© pot, linear taper
- Release, a 1 M screwdriver control wired as a variable resistor to ground. Turned clockwise, it has less resistance, so C4 lets go faster: 0.3 s fully clockwise, 1.3 s counterclockwise (63 % of the way back). Taper assumed linear.
- Supply a, 234 V ac, 60 Hz
- Stands in for T3 and the doubler with the parts beside it. The doublerβs two caps sit in series across the winding, and the operating point canβt be solved through them, so the supply runs as a center-tapped full-wave pair of 234 V halves, twice the 117 V winding, as the doubler makes.
- Supply b, 234 V ac, 60 Hz
- The other half of the stand-in, half a cycle behind.
- Supply R, 600βΞ©
- Stands for the windingβs and the selenium rectifiersβ resistance. Set so the line comes to the drawingβs 272 V.
- Supply R, 600βΞ©
- The same for the other half.
- Rectifier, 1N4001
- One selenium rectifier, run as a silicon diode with the resistance beside it.
- Rectifier, 1N4001
- The other rectifier, for the other half cycle.
- C7, C8A, 40βΒ΅F electrolytic
- C7 and C8A, 80 Β΅F each. In the doubler they are in series across the output, so they act as 40 Β΅F here.
- R13, 10βkΞ©
- R13, 10 k 1 W, from 272 V to the 210 V line that feeds V1 and the threshold divider.
- C8B, 10βΒ΅F electrolytic
- C8B, 10 Β΅F, filters the 210 V line. It rises to 290 V on the drawing at 20 dB of compression, when V1 draws less.
- R14, 7βkΞ©
- R14, 7 k 5 W, from 272 V to T2βs center tap (152 V on the drawing).
- C8C, 40βΒ΅F electrolytic
- C8C, 40 Β΅F, on T2βs center tap.
About this version
- As drawn
- The factory drawing 8192-1, fed unbalanced on the 15 kΞ© bridging input and loaded with 600 Ξ©.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.