Six-stage JFET phaser with feedback, 1975 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Electro-Harmonix Bad Stone (first version).
Six op-amp stages, each set by a JFET, turn the guitar’s phase, and mixed with the dry signal they cancel at three notches. A triangle LFO or a foot pedal moves the JFET gates. Color sends part of the phased signal back to the input, and the Bend toggle takes the dry signal out.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 buffers the guitar into six all-pass stages. Each one passes every pitch at the same level and turns its phase, 90° at 1 / (2π R C), where R is the stage’s JFET beside its 120 kΩ and C is .01 µF. Mixed with the dry signal, six stages make three notches. With the JFETs pinched off the stages turn at about 130 Hz, and the notches sit at about 120 and 460 Hz. As the gates come up toward 0 V the notches move up. With the gates at the middle of the LFO’s swing they sit near 590 Hz, 2.4 kHz and 8.6 kHz. B3 and B4 make the triangle, from one sweep every 5.5 seconds at 0 on Rate to about 77 a second at full. Color sends part of the phased signal back to the input, and at full the peaks between the notches rise about 5 dB. The Bend toggle puts 2.2 MΩ in the dry path, so mostly the wet signal comes out and the sweep bends the pitch. The footswitch picks the LFO or the treadle. Two batteries make ±9 V. The op-amps, the zener voltage and the pot tapers are assumed, and the trims are set to suit the 2N4302 here, so a real pedal’s sweep may sit elsewhere.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- −9 V, -9 V
- The second 9 V battery, the −9 V rail.
- R1, 100 kΩ
- From the input jack to ground. With Q1’s input it sets the input impedance, about 100 kΩ.
- C1, 10 nF
- Input coupling cap.
- R2, 100 kΩ
- Into Q1’s base. With R3 it divides the guitar slightly, and the Color signal comes in at its far end.
- R3, 10 MΩ
- Holds Q1’s base at ground.
- Q1, 2N5087
- A PNP emitter follower. It drives the stages and the dry side of the mix.
- R4, 47 kΩ
- Q1’s emitter load from +9 V.
- C3, 100 nF
- Couples Q1 to the first stage.
- R5, 120 kΩ
- Into the minus input. With the 120 kΩ feedback resistor it makes the inverting half of the stage, a gain of one, inverted.
- R6, 120 kΩ
- Feedback, equal to the input resistor, so every pitch comes out at the same level and only the phase moves.
- C4, 10 nF
- Feeds the plus input. Against the JFET and the 120 kΩ beside it, it sets where this stage turns the phase 90°, about 130 Hz with the JFET pinched off.
- R7, 120 kΩ
- From the plus input to ground, beside the JFET.
- Q2, 2N4302
- A 2N4302 JFET used as a resistor that the gate line varies. The closer its gate comes to 0 V, the lower its resistance and the higher this stage’s 90° point.
- A1, LM324
- A quarter of a quad op-amp, the first of six phase-shift stages. An LM324 is assumed from the pin numbers.
- R8, 27 kΩ
- From the output to −9 V. It keeps current flowing in the op-amp’s output stage, which cuts its crossover distortion.
- R9, 120 kΩ
- Into the minus input, as in the first stage.
- R10, 120 kΩ
- Feedback, 120 kΩ.
- C5, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R11, 120 kΩ
- Beside this stage’s JFET, 120 kΩ.
- Q3, 2N4302
- This stage’s JFET, on the same gate line.
- A2, LM324
- Phase-shift stage 2.
- R12, 27 kΩ
- 27 kΩ to −9 V, as on every stage.
- R13, 120 kΩ
- Into the minus input, as in the first stage.
- R14, 120 kΩ
- Feedback, 120 kΩ.
- C6, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R15, 120 kΩ
- Beside this stage’s JFET, 120 kΩ.
- Q4, 2N4302
- This stage’s JFET, on the same gate line.
- A3, LM324
- Phase-shift stage 3.
- R16, 27 kΩ
- 27 kΩ to −9 V, as on every stage.
- R17, 120 kΩ
- Into the minus input, as in the first stage.
- R18, 120 kΩ
- Feedback, 120 kΩ.
- C7, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R19, 120 kΩ
- Beside this stage’s JFET, 120 kΩ.
- Q5, 2N4302
- This stage’s JFET, on the same gate line.
- A4, LM324
- Phase-shift stage 4.
- R20, 27 kΩ
- 27 kΩ to −9 V, as on every stage.
- R21, 120 kΩ
- Into the minus input, as in the first stage.
- R22, 120 kΩ
- Feedback, 120 kΩ.
- C8, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R23, 120 kΩ
- Beside this stage’s JFET, 120 kΩ.
- Q6, 2N4302
- This stage’s JFET, on the same gate line.
- B1, LM324
- Phase-shift stage 5.
- R24, 27 kΩ
- 27 kΩ to −9 V, as on every stage.
- R25, 75 kΩ
- 75 kΩ into the last stage’s minus input, smaller than the others. With R29 this stage boosts the signal as it turns it.
- R26, 120 kΩ
- Feedback, 120 kΩ.
- C9, 10 nF
- Feeds the plus input, .01 µF as in every stage.
- R27, 120 kΩ
- Beside this stage’s JFET, 120 kΩ.
- Q7, 2N4302
- This stage’s JFET, on the same gate line.
- B2, LM324
- The sixth stage. Its output is the wet signal.
- R28, 27 kΩ
- 27 kΩ to −9 V, as on every stage.
- R29, 300 kΩ
- From the last stage’s minus input to ground. With R25 at 75 kΩ, low notes come out 1.6 times larger, inverted, and high notes 1.4 times.
- Trim, 100 kΩ pot, linear taper
- The internal 100 kΩ trim, a variable resistor beside R30. It sets the wet signal’s level against the dry, so the notches are deep. Set at 0.45, assumed.
- R30, 10 kΩ
- Across the trim, so the wet side never passes more than about 9 kΩ there.
- R31, 5.6 kΩ
- The wet signal into the mix.
- C10, 100 nF
- Couples the dry signal to the mix.
- R32, 2.2 MΩ
- In the dry path. With Bend off the toggle shorts it. With Bend on, almost no dry signal gets through it.
- R33, 10 kΩ
- The dry signal into the mix.
- C11, 100 nF
- Output coupling cap, to the jack.
- C12, 100 nF
- Takes the wet signal into the Color path.
- R34, 4.7 kΩ
- With R35 and the rest of the path, it divides the feedback down.
- R35, 6.8 kΩ
- In the Color path.
- C13, 560 pF
- Trims the highs from the feedback.
- R36, 75 kΩ
- The smallest the Color path’s resistance gets, with Color full up.
- Color, 1 MΩ pot, linear taper
- Color, 1 MΩ, a variable resistor in the feedback path. Turned up, its resistance drops and more of the phased signal goes back into Q1’s base, so the peaks between the notches ring. The taper is assumed.
- C2, 47 nF
- Couples the Color signal into Q1’s base.
- R37, 100 kΩ
- From −9 V to the zener.
- Q8, 6.2 V zener, in breakdown
- A 2N3563 with its base-emitter junction broken down, used as a zener. It holds the bias near −5.9 V as the battery runs down. Its breakdown voltage isn’t on the drawing, so a 6.2 V zener stands in.
- R38, 39 kΩ
- From the zener to the top of the Bias trim.
- Bias, 500 kΩ pot, linear taper
- The internal 500 kΩ Bias trim. It sets how far below 0 V the JFET gates sit. Set at 0.75 for this file’s JFET, an assumed setting.
- R39, 470 kΩ
- The bias into the control node. With R42 it averages the bias and the sweep.
- C14, 47 nF
- Smooths the control node. With the two 470 kΩ it starts to round off the sweep above about 14 Hz.
- R40, 10 kΩ
- From the control node to the JFET gates.
- Pedal, 100 kΩ pot, linear taper
- The treadle’s pot, 100 kΩ from +9 V (toe down) to −9 V. With the footswitch at pedal, its wiper sets the gates. The taper is assumed.
- R41, 160 kΩ
- From the footswitch to the Width trim.
- Width, 100 kΩ pot, linear taper
- The internal 100 kΩ trim that sets how far the triangle or the pedal swings the gates. Set at 0.2, an assumed setting, so the gates swing about 0.4 V across the JFETs’ pinch-off.
- R42, 470 kΩ
- The sweep into the control node.
- R43, 10 kΩ
- Between the integrator’s cap and its minus input.
- B3, LM324
- The integrator. Its output ramps up and down at a rate set by Rate, and that ramp is the triangle.
- C15, 2.2 µF
- The integrator’s cap.
- R45, 75 kΩ
- The triangle into the comparator’s plus input.
- R46, 120 kΩ
- Positive feedback. With R45 it sets where the comparator flips, at about 0.6 times its output.
- B4, LM324
- The comparator. It flips each time the triangle reaches a switch point, and its square wave turns the ramp around.
- R47, 10 kΩ
- Holds the comparator’s minus input near ground.
- R48, 10 MΩ
- From the comparator’s output to its minus input.
- C16, 22 nF
- Across R48.
- C17, 1 µF electrolytic
- From the square wave to −9 V. It slows the square’s edges.
- R44, 1.8 kΩ
- In series with Rate. It sets the top speed.
- Rate, 1 MΩ pot, reverse audio taper
- Rate, 1 MΩ, a variable resistor from the square wave into the integrator. Clockwise its resistance drops and the sweep speeds up. Reverse audio is assumed, since the taper isn’t marked.
About this version
- Stock
- The first version, from the factory drawing. Two 9 V batteries, LM324 op-amps, 2N4303 JFETs in place of the 2N4302.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.