Two-transistor silicon fuzz with diodes at the output, 1969 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Electro-Harmonix Muff Fuzz (two-transistor version).
Two silicon transistors direct coupled, with feedback from the second stage’s emitter to the first stage’s base, and two diodes to ground at the output. The feedback makes the input impedance very low, so the pickup and the input cap set the tone.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 has no emitter resistor. R1 feeds Q2’s emitter back to Q1’s base, so the two stages hold each other’s bias. That feedback also makes the input look like about 460 Ω. The pickup’s coil and C1 tune a peak near 290 Hz into that low input, so the guitar’s lows and highs are both cut before Q1. From the guitar to Q2’s collector the gain is about 34 dB at the peak. On a 200 mV pick Q1’s collector swings from about 0.1 V to 3 V, and Q2 cuts off on every other half wave. The diodes after C2 hold what’s left to about 0.5 V each way before the Volume pot. With the input that low, turning the guitar’s volume down also cuts its treble.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C1, 100 nF
- Input coupling cap.
- Q1, 2N5133
- First gain stage, its emitter straight to ground.
- R1, 100 kΩ
- Feedback from Q2’s emitter to Q1’s base. It sets the bias of both stages and holds down Q1’s gain.
- R2, 100 kΩ
- Q1’s base to ground.
- R3, 100 kΩ
- Q1’s collector load.
- Q2, 2N5133
- Second gain stage, direct coupled to Q1’s collector.
- R4, 10 kΩ
- Q2’s collector load.
- R5, 2.7 kΩ
- Q2’s emitter resistor, unbypassed, so Q2’s gain is about 3.7.
- C2, 100 nF
- Output coupling cap.
- D1, D2, 1N914 / 1N4148, one each way
- Two silicon diodes to ground, one each way. Their type isn’t on the drawing, so they’re 1N914s.
- Volume, 100 kΩ pot, audio taper
- Output level, a 100 kΩ log pot.
- C3, 50 µF electrolytic
- Across the supply.
About this version
- 2N5133
- Two 2N5133 silicon transistors, as the redraw marks them.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.