Two-channel 6L6 reverb amp with twin-T filters and lamp tremolo, mid 1960s style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Gibson GA-45RVT Saturn.
Two 6EU7 channels, each with bass, treble and loudness and a fixed notch in the mids, mixed through a second notch near 70 Hz into a cathodyne and 6FQ7 drivers that push two 6L6GCs in fixed bias. The Reverb channel has the springs and a tremolo, a lamp beside a photocell on its second grid.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each channel starts on one half of a 6EU7 with no coupling cap at the input. The tone stack after it has a Bass pot with a cap across each half and a Treble pot between a .001 µF and a cap to ground. The Treble wiper is the top of the Loudness pot. After the Loudness pot comes a twin-T: two .0047 µF in series and two 82 kΩ in series, each with a leg to ground from its middle. Near 400 Hz the two paths cancel, so the channel has a fixed dip in the mids, about 25 dB deep. The second 6EU7 stage runs on a 470 kΩ plate resistor. The two channels meet through 220 kΩ and 100 kΩ and pass a second twin-T, tuned near 70 Hz, on the way to a 6EU7 cathodyne. A 6FQ7 a side drives two 6L6GCs in fixed bias with no feedback. The Reverb channel feeds the springs from the input of its tone stack, through a bridged-T, and the reverb comes back into that channel’s second stage. The tremolo works on the Reverb channel too. An oscillator swings the current through a small bulb, and a photocell beside the bulb pulls the second stage’s grid down as the bulb brightens.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 68k, 68 kΩ
- Input 1’s resistor, 68 kΩ straight to the first grid. There’s no coupling cap at the input.
- 68k, 68 kΩ
- From the first grid to input 2’s tip, 68 kΩ. A guitar in input 2 goes through it and input 1’s 68 kΩ is left hanging, so the two inputs sound about the same.
- 1M, 1 MΩ
- Input 2’s 1 MΩ to ground. It’s the first grid’s path to ground, through the 68 kΩ.
- V1B, 6EU7
- One half of V1, a 6EU7, the Normal channel’s first stage.
- 100k, 100 kΩ
- Plate resistor for V1B. The drawing reads +173 V on the plate.
- 1.5k, 1.5 kΩ
- Cathode resistor for V1B, +1.38 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V1B’s cathode resistor, so the stage has its full gain.
- .01µ, 10 nF
- Coupling cap to the tone stack, .01 µF.
- .0022µ, 2.2 nF
- Across the top half of the Bass pot. It lets the treble around that half.
- Bass, 1 MΩ pot, audio taper
- Bass, 1 MΩ audio, with a cap across each half. Turned up, the wiper moves toward the top, so the bass gets through with less loss and more of it reaches the Loudness pot.
- .0015µ, 1.5 nF
- Across the bottom half of the Bass pot.
- 22k, 22 kΩ
- From the bottom of the Bass pot to ground, 22 kΩ.
- 100k, 100 kΩ
- From the Bass wiper to the Treble wiper, on the Normal channel only. The Reverb channel joins the two wipers straight.
- .001µ, 1 nF
- The treble path, from the stack’s input to the top of the Treble pot.
- Treble, 1 MΩ pot, audio taper
- Treble, 1 MΩ audio. Its wiper is the tone stack’s output. Turned up, the wiper moves toward the .001 µF and the stack passes more treble.
- .01µ, 10 nF
- From the bottom of the Treble pot to ground, .01 µF.
- Loudness, 1 MΩ pot, audio taper
- Loudness, 1 MΩ audio, the channel’s volume, from the Treble wiper to ground. Its wiper feeds the twin-T.
- 1M, 1 MΩ
- From the Loudness wiper to the bottom of the Treble pot, 1 MΩ, as drawn.
- .0047µ, 4.7 nF
- First cap of the twin-T’s cap path.
- .0047µ, 4.7 nF
- Second cap of the twin-T’s cap path, into the second stage’s grid.
- 39k, 39 kΩ
- From the middle of the two .0047 µF toward ground.
- 82k, 82 kΩ
- First resistor of the twin-T’s resistor path.
- 82k, 82 kΩ
- Second resistor of the twin-T’s resistor path, into the second stage’s grid.
- .01µ, 10 nF
- From the middle of the two 82 kΩ toward ground. With the caps’ path beside it, the two paths cancel each other near 400 Hz, a notch in the mids.
- 4.7k, 4.7 kΩ
- The twin-T’s common leg to ground, 4.7 kΩ. It keeps the notch from going all the way down, about 25 dB deep.
- V4B, 6EU7
- One half of V4, a 6EU7, the Normal channel’s second stage.
- 470k, 470 kΩ
- Plate resistor for V4B, 470 kΩ. The drawing reads +130 V on the plate, so the stage runs on about 0.3 mA.
- 4.7k, 4.7 kΩ
- Cathode resistor for V4B, +1.35 V on the drawing.
- .1µ, 100 nF
- Only .1 µF across V4B’s 4.7 kΩ, so the stage has its full gain only from a few hundred hertz up, and the bass is held down here.
- 100p, 100 pF
- From V4B’s plate to ground. With the 470 kΩ plate resistor it trims the highest treble.
- 220k, 220 kΩ
- Mixing resistor from V4B’s plate to the node where both channels meet, 220 kΩ. The Reverb channel goes through 100 kΩ.
- 68k, 68 kΩ
- Input 3’s resistor, 68 kΩ straight to the first grid. There’s no coupling cap at the input.
- 68k, 68 kΩ
- From the first grid to input 4’s tip, 68 kΩ. A guitar in input 4 goes through it and input 3’s 68 kΩ is left hanging, so the two inputs sound about the same.
- 1M, 1 MΩ
- Input 4’s 1 MΩ to ground. It’s the first grid’s path to ground, through the 68 kΩ.
- V1A, 6EU7
- One half of V1, a 6EU7, the Reverb channel’s first stage.
- 100k, 100 kΩ
- Plate resistor for V1A. The drawing reads +173 V on the plate.
- 1.5k, 1.5 kΩ
- Cathode resistor for V1A, +1.38 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V1A’s cathode resistor, so the stage has its full gain.
- .047µ, 47 nF
- Coupling cap to the tone stack, .047 µF. The Normal channel has .01 µF here, so this channel keeps more bass.
- 12k, 12 kΩ
- In series ahead of the Bass pot, on the Reverb channel only. It holds back the bass path slightly.
- .0015µ, 1.5 nF
- Across the top half of the Bass pot. It lets the treble around that half.
- Bass, 1 MΩ pot, audio taper
- Bass, 1 MΩ audio, with a cap across each half. Turned up, the wiper moves toward the top, so the bass gets through with less loss and more of it reaches the Loudness pot.
- .0015µ, 1.5 nF
- Across the bottom half of the Bass pot.
- 68k, 68 kΩ
- From the bottom of the Bass pot to ground, 68 kΩ. The Normal channel has 22 kΩ here.
- .001µ, 1 nF
- The treble path, from the stack’s input to the top of the Treble pot.
- Treble, 1 MΩ pot, audio taper
- Treble, 1 MΩ audio. Its wiper is the tone stack’s output. Turned up, the wiper moves toward the .001 µF and the stack passes more treble.
- .033µ, 33 nF
- From the bottom of the Treble pot to ground, .033 µF. The Normal channel has .01 µF here.
- Loudness, 1 MΩ pot, audio taper
- Loudness, 1 MΩ audio, the channel’s volume, from the Treble wiper to ground. Its wiper feeds the twin-T.
- 1M, 1 MΩ
- From the Loudness wiper to the bottom of the Treble pot, 1 MΩ, as drawn.
- .0047µ, 4.7 nF
- First cap of the twin-T’s cap path.
- .0047µ, 4.7 nF
- Second cap of the twin-T’s cap path, into the second stage’s grid.
- 39k, 39 kΩ
- From the middle of the two .0047 µF toward ground.
- 82k, 82 kΩ
- First resistor of the twin-T’s resistor path.
- 82k, 82 kΩ
- Second resistor of the twin-T’s resistor path, into the second stage’s grid.
- .01µ, 10 nF
- From the middle of the two 82 kΩ toward ground. With the caps’ path beside it, the two paths cancel each other near 400 Hz, a notch in the mids.
- 4.7k, 4.7 kΩ
- The twin-T’s common leg to ground, 4.7 kΩ. It keeps the notch from going all the way down, about 25 dB deep.
- V4A, 6EU7
- One half of V4, a 6EU7, the Reverb channel’s second stage. The reverb comes in on its grid, and the tremolo’s photocell pulls its grid down.
- 470k, 470 kΩ
- Plate resistor for V4A, 470 kΩ. The drawing reads +130 V on the plate, so the stage runs on about 0.3 mA.
- 4.7k, 4.7 kΩ
- Cathode resistor for V4A, +1.35 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V4A’s cathode resistor, so the stage has its full gain. The Normal channel has only .1 µF here.
- 100k, 100 kΩ
- Mixing resistor from V4A’s plate to the node where both channels meet, 100 kΩ. The Normal channel goes through 220 kΩ.
- .047µ, 47 nF
- Coupling cap from the mixing node into the second twin-T.
- .0022µ, 2.2 nF
- First cap of the second twin-T’s cap path.
- .0022µ, 2.2 nF
- Second cap of the cap path, into the cathodyne’s grid.
- 510k, 510 kΩ
- From the middle of the two .0022 µF to ground.
- 1M, 1 MΩ
- First resistor of the second twin-T’s resistor path.
- 1M, 1 MΩ
- Second resistor of the resistor path, into the cathodyne’s grid.
- .0047µ, 4.7 nF
- From the middle of the two 1 MΩ to ground. With the cap path beside it the two paths cancel near 70 Hz, a deep notch just over the 60 Hz hum, and the lowest notes come through thinner.
- 150k, 150 kΩ
- First half of the bridged-T into the Reverb pot, from the Reverb channel’s stack input.
- 150k, 150 kΩ
- Second half of the bridged-T, to the Reverb pot’s top.
- 500p, 500 pF
- Across both 150 kΩ. It carries the treble past the bridged-T.
- .01µ, 10 nF
- From the middle of the two 150 kΩ to ground. With the 500 pF it makes a dip near 500 Hz, so less of the low mids reaches the springs.
- Reverb, 1 MΩ pot, audio taper
- Reverb, 1 MΩ audio. Its wiper is V2A’s grid, so it sets how hard the springs are driven.
- V2A, 6EU7
- One half of V2, a 6EU7, the reverb’s first gain stage.
- 100k, 100 kΩ
- Plate resistor for V2A, +175 V on the drawing.
- 1.5k, 1.5 kΩ
- Cathode resistor for V2A, +1.35 V on the drawing.
- .1µ, 100 nF
- Only .1 µF across V2A’s cathode resistor, so the stage has less gain below about 1 kHz and less bass reaches the springs.
- 500p, 500 pF
- Coupling cap to the reverb driver, only 500 pF. Into 470 kΩ it cuts below about 700 Hz, so the springs are driven mostly with treble.
- 470k, 470 kΩ
- The reverb driver’s grid resistor.
- V3B, 12AU7 / ECC82
- One half of V3, a 12AU7, the reverb driver. Its cathode resistor isn’t bypassed. The drawing reads +8.4 V on it, about 8.4 mA.
- 1k, 1 kΩ
- Cathode resistor for the reverb driver.
- T3, 25 kΩ to 8 Ω, 20 H primary, 50 mH leakage
- The reverb transformer, from the driver’s plate to the spring unit. The drawing reads 13 V across its primary, so its resistance is set at 1.5 kΩ. Its other figures, 25 kΩ into 8 Ω, are typical for the job.
- Unit in R, 800 mΩ
- Resistance of the reverb unit’s input coil. The current through it drives the springs, which play from a measured tank’s impulse response, a recording of how the real springs ring after a click.
- Unit in L, 1.1 mH
- Inductance of the reverb unit’s input coil, a measured long tank’s figure.
- Unit out L, 350 mH
- The reverb unit’s output coil, 0.35 H, from V2B’s grid to ground. The springs come back in series with it.
- Unit out R, 181 Ω
- Resistance of the unit’s output coil, 181 Ω, a measured long tank’s figure.
- 220k, 220 kΩ
- Grid resistor for the reverb recovery stage.
- .001µ, 1 nF
- From the recovery grid to ground. It trims the springs’ highest treble.
- V2B, 6EU7
- The other half of V2, the reverb recovery stage.
- 100k, 100 kΩ
- Plate resistor for V2B, +175 V on the drawing.
- 1.5k, 1.5 kΩ
- Cathode resistor for V2B, +1.35 V on the drawing.
- 20µ, 20 µF electrolytic
- Bypass for V2B’s cathode resistor.
- .0047µ, 4.7 nF
- Coupling cap from the recovery stage.
- 270k, 270 kΩ
- From the recovery stage into V4A’s grid, where the reverb meets the Reverb channel’s dry signal.
- 5k, 5 kΩ
- From the +262 V node to the OA2, 5 kΩ 5 W. It carries the tremolo’s current and the OA2’s, about 23 mA.
- V7, OA2 regulator
- V7, an OA2 gas regulator tube. It holds the tremolo’s supply near 148 V, so the lamp’s idle glow doesn’t move with the rest of the supply.
- 150k, 150 kΩ
- Plate resistor for the oscillator, from the +148 V node. The drawing reads +76 V on the plate.
- V5B, 6EU7
- The other half of V5 (V5A is the cathodyne in the power amp), the tremolo oscillator. Its cathode goes straight to ground.
- .022µ, 22 nF
- First cap of the oscillator’s phase-shift ladder.
- 330k, 330 kΩ
- The ladder’s first leg to ground.
- .022µ, 22 nF
- Second ladder cap.
- 120k, 120 kΩ
- In series with the Frequency pot, the ladder’s second leg. It sets the top speed.
- Frequency, 1.5 MΩ pot, reverse audio taper
- Frequency, 1.5 MΩ reverse audio, as a variable resistor from the 120 kΩ to the foot switch. Turned up, its resistance drops and the oscillator runs faster.
- .01µ, 10 nF
- Third ladder cap, into the grid. At one frequency the three caps and legs turn the plate’s swing upside down by the time it reaches the grid, so the stage oscillates at that frequency.
- 4.7M, 4.7 MΩ
- Grid leak for the oscillator, and the ladder’s last leg. The drawing reads −0.5 V on the grid.
- .022µ, 22 nF
- Couples the oscillator’s swing toward the Depth pot.
- 1M, 1 MΩ
- In series with the Depth pot. With the pot it divides the oscillator’s swing down.
- Depth, 250 kΩ pot, audio taper
- Depth, 250 kΩ audio, to ground. Its wiper is the lamp driver’s grid, so it sets how far the lamp’s current swings.
- V3A, 12AU7 / ECC82
- The other half of V3, the lamp driver. Its plate current runs through the lamp, so the lamp brightens and dims with the oscillator.
- 500Ω, 500 Ω pot, linear taper
- A 500 Ω wire-wound trim as a variable resistor in the lamp driver’s cathode. It sets the lamp’s idle current. The drawing reads +1.15 V on the cathode. Its setting isn’t on the drawing, so it’s set near that voltage.
- Lamp, 24 V bulb, 18 mA
- The bulb in the photocell assembly Z1, an LDR-500 on the drawing’s parts list, from the +148 V node to the lamp driver’s plate. The drawing reads 15 V across it at idle. It glows dimly at idle and brightens as the driver’s current rises.
- Cell, Gibson LDR-500 cell
- The photocell in Z1, from V4A’s grid to ground. Lit, its resistance drops and it pulls the grid down, so the Reverb channel and its reverb get quieter. Dark, it’s about 1 MΩ and hardly loads the grid.
- V6, 6EU7
- 6EU7, a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 100k, 100 kΩ
- The cathodyne’s plate resistor, the output to tube B.
- 2.2k, 2.2 kΩ
- The cathodyne’s bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 100k, 100 kΩ
- The cathodyne’s cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470 kΩ
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathode’s high DC voltage. It’s the grid’s only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ω.
- .022µ, 22 nF
- Coupling cap from the inverter to side A’s driver.
- .022µ, 22 nF
- Coupling cap from the inverter to side B’s driver.
- 2.2k, 2.2 kΩ
- The drivers’ cathode resistor, 2.2k Ω to ground for both halves, with no bypass cap. The two cathodes share it, so the pair works somewhat like a long-tail pair: what one half gains in current the other loses, which evens out the two sides’ swings.
- 220k, 220 kΩ
- Grid leak for side A’s driver, to ground.
- V9a, 6CG7
- 6CG7, side A’s driver: a gain stage that raises the inverter’s signal about 9 times on its way to tube A’s grids. The other half drives side B, and the two share one cathode resistor.
- 47k, 47 kΩ
- The driver’s plate resistor, 47k Ω from the node for the drivers.
- .047µ, 47 nF
- Coupling cap from the driver’s plate to tube A’s grids.
- 220k, 220 kΩ
- Grid leak for side B’s driver, to ground.
- V9b, 6CG7
- The other half of the 6CG7, side B’s driver.
- 47k, 47 kΩ
- The driver’s plate resistor, 47k Ω from the node for the drivers.
- .047µ, 47 nF
- Coupling cap from the driver’s plate to tube B’s grids.
- 1k, 1 kΩ
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current.
- 1k, 1 kΩ
- Grid stopper for tube B.
- V7, 6L6GC
- 6L6GC, tube A of the push-pull pair, cathode grounded, biased from the fixed bias supply.
- V8, 6L6GC
- 6L6GC, tube B of the pair.
- 100k, 100 kΩ
- Grid leak for tube A, returned to the bias supply. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 100k, 100 kΩ
- Grid leak for tube B.
- 470, 470 Ω
- Screen resistor for tube A. It limits the screen current when the tube is driven hard.
- 470, 470 Ω
- Screen resistor for tube B.
- 4 H, 4 H
- The choke from the reservoir cap to B+, as on the amp’s drawing. The output transformer’s center tap, the screens and everything after them hang past it, so all of their current runs through it. It passes DC with little drop. With the cap after it, it would filter ripple, but ripple isn’t modeled here. Typical of the part.
- 47, 47 Ω
- The choke’s winding resistance, typical. With the output tubes’ whole current through it, it’s most of the DC drop between the reservoir and B+.
- 20µ, 20 µF electrolytic
- Filter cap on B+ after the choke, where the output transformer’s center tap and the screens hang.
- 4k, 4 kΩ
- Dropping resistor from the screen supply node to the node for the drivers, as on the Gibson GA-45RVT Saturn drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 4.7k, 4.7 kΩ
- Dropping resistor from the node for the drivers to the node for the cathodyne, as on the Gibson GA-45RVT Saturn drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20µ, 20 µF electrolytic
- Filter cap at the node for the cathodyne. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 4.7k, 4.7 kΩ
- Dropping resistor from the node for the cathodyne to the node for the preamp, as on the Gibson GA-45RVT Saturn drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 10µ, 10 µF electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 1.5k, 1.5 kΩ
- Dropping resistor from the node for the drivers to the node for the reverb driver and the tremolo, as on the Gibson GA-45RVT Saturn drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 10µ, 10 µF electrolytic
- Filter cap at the node for the reverb driver and the tremolo. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 6.6 kΩ to 16 Ω, 40 H primary, 10 mH leakage
- The output transformer, 6.6 kΩ plate to plate into 16 Ω, center tap on B+ after the choke. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 355 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 355 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 355 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 60 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 60 Ω
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 20µ, 20 µF electrolytic
- The reservoir cap. It feeds the choke, and past it the output transformer’s center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Bias tap, 51 V ac, 60 Hz
- The power transformer’s bias tap, 50.6 V ac, as a sine source at the mains frequency. Typical of the part.
- tap R, 100 Ω
- The bias tap’s own resistance, 100 Ω, typical. The drawing has no resistor between the tap and the diode.
- Bias diode, 1N4001
- The bias rectifier, a silicon diode turned so the supply comes out negative.
- 10µ, 10 µF electrolytic
- Filter cap on the bias supply, its plus side to ground.
- 7.5k, 7.5 kΩ
- Second resistor of the bias supply, 7.5k Ω to the bias line. With the cap after it, it filters the ripple a second time.
- 10µ, 10 µF electrolytic
- Second filter cap, on the bias line, its plus side to ground.
- 22k, 22 kΩ
- From the bias line to ground, 22k Ω. With the 7.5k Ω above it, it divides the supply down to the bias. There’s no bias pot, so change this resistor to change the bias. Bigger runs the tubes colder.
- Coil R, 17.4 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 16 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 512 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 928 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 28.6 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 4.26 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 4.38 Ω
- Limits what Loss L2 adds.
- Tank R, 167 Ω
- Height of the bass resonance, about 185 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 42.2 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 110 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The 6EU7 model is fitted to the Tung-Sol reissue plate chart. The 12AU7s use the 12AU7 model. The photocell and its bulb are the bench’s Gibson LDR-500, as the drawing’s parts list names it. The reverb transformer and unit are typical.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.