Two-channel 7189 amp with reverb and vibrato, 1965 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Danelectro DM-25.
Two 12AX7 channels with Bass, Treble and Volume, mixed through 330 kΩ into a 12AX7 driver and cathodyne and two 7189s on cathode bias. Channel 2 has a crystal reverb unit and a lamp-and-photocell vibrato.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each channel is one 12AX7 stage, a tone network and a Volume. The two first stages share a cathode resistor, and each has 2.2 MΩ from the far side of its coupling cap back to its grid, which lowers the gain somewhat. In each tone network two 220 kΩ resistors run in series, and two .0022 µF caps go from them to the Treble pot’s wiper. Turned down, the Treble pot grounds the caps and cuts the highs. The two Volume wipers meet at the driver’s grid through 330 kΩ each, so each channel loads the other. The reverb and vibrato work on channel 2. A 6FQ7 drives the reverb unit’s crystal input element from both sides. The output element comes back through the Reverb pot and 2.2 MΩ into the mix. The vibrato varies the level. A 12AX7 phase-shift oscillator runs a few times a second and drives the other half of the tube, which flashes a neon lamp. The lamp shines on a photocell from channel 2’s tone network to ground. The 7189s idle on one 118 Ω cathode resistor with no bypass cap.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 68k, 68 kΩ
- Input resistor for jack 1, on channel 1.
- 68k, 68 kΩ
- Input resistor for jack 2, the same.
- 1M, 1 MΩ
- Grid resistor for channel 1’s first stage.
- V1b, 12AX7 / ECC83 / 7025
- Half of V1, a 12AX7, channel 1’s first stage. The two halves share one cathode resistor.
- 330k, 330 kΩ
- Plate resistor, 330 kΩ from the 220 V node (+105 V on the drawing).
- .02µ, 20 nF
- Coupling cap into channel 1’s tone network.
- 2.2M, 2.2 MΩ
- From the grid to the far side of the coupling cap, 2.2 MΩ. It feeds some of the plate’s inverted signal back to the grid, which lowers the stage’s gain, and it is the network’s path to ground for DC.
- 220k, 220 kΩ
- First of the two 220 kΩ resistors in series at the tone network’s input.
- 220k, 220 kΩ
- Second of the two 220 kΩ resistors. With the .0022 µF caps it forms a treble cut that the Treble pot sets.
- .0022µ, 2.2 nF
- From the network’s input to the Treble pot’s wiper.
- .0022µ, 2.2 nF
- From the middle of the two 220 kΩ resistors to the Treble pot’s wiper.
- 680p, 680 pF
- From the Treble pot’s wiper to the Bass pot’s top, around the second 220 kΩ.
- Treble 1 1M, 1 MΩ pot, audio taper
- Treble, 1 MΩ. Its wiper takes the two .0022 µF caps. Turned down, the wiper nears ground and the caps bleed the treble off. Turned up, it nears the top lug, which feeds them through 50 pF to the Volume’s wiper. Audio taper and brighter clockwise are assumed.
- 50p, 50 pF
- From the Treble pot’s top lug to the Volume’s wiper, around the Volume pot.
- .0015µ, 1.5 nF
- From the Bass pot’s top to its wiper. With the Bass turned down it still passes the treble.
- Bass 1 1M, 1 MΩ pot, audio taper
- Bass, 1 MΩ. Its wiper is the Volume’s top. Turned up, the wiper nears the top lug and the lows come straight through. Turned down, more of the track is in series and only the .0015 µF passes. Audio taper and more bass clockwise are assumed.
- .006µ, 6 nF
- From the Bass wiper to the Bass pot’s bottom lug.
- 100k, 100 kΩ
- The bottom of the tone network, 100 kΩ to ground.
- Vol 1 1M, 1 MΩ pot, audio taper
- Volume 1, 1 MΩ. Its wiper feeds the mixing node through 330 kΩ. Audio taper is assumed.
- 330k, 330 kΩ
- Mixing resistor from Volume 1’s wiper to V2a’s grid.
- 68k, 68 kΩ
- Input resistor for jack 3, on channel 2.
- 68k, 68 kΩ
- Input resistor for jack 4, the same.
- 1M, 1 MΩ
- Grid resistor for channel 2’s first stage.
- V1a, 12AX7 / ECC83 / 7025
- Half of V1, a 12AX7, channel 2’s first stage. The two halves share one cathode resistor.
- 330k, 330 kΩ
- Plate resistor, 330 kΩ from the 220 V node (+105 V on the drawing).
- .02µ, 20 nF
- Coupling cap into channel 2’s tone network.
- 2.2M, 2.2 MΩ
- From the grid to the far side of the coupling cap, 2.2 MΩ. It feeds some of the plate’s inverted signal back to the grid, which lowers the stage’s gain, and it is the network’s path to ground for DC.
- 220k, 220 kΩ
- First of the two 220 kΩ resistors in series at the tone network’s input.
- 220k, 220 kΩ
- Second of the two 220 kΩ resistors. With the .0022 µF caps it forms a treble cut that the Treble pot sets.
- .0022µ, 2.2 nF
- From the network’s input to the Treble pot’s wiper.
- .0022µ, 2.2 nF
- From the middle of the two 220 kΩ resistors to the Treble pot’s wiper.
- 680p, 680 pF
- From the Treble pot’s wiper to the Bass pot’s top, around the second 220 kΩ.
- Treble 2 1M, 1 MΩ pot, audio taper
- Treble, 1 MΩ. Its wiper takes the two .0022 µF caps. Turned down, the wiper nears ground and the caps bleed the treble off. Turned up, it nears the top lug, which feeds them through 50 pF to the Volume’s wiper. Audio taper and brighter clockwise are assumed.
- 50p, 50 pF
- From the Treble pot’s top lug to the Volume’s wiper, around the Volume pot.
- .0015µ, 1.5 nF
- From the Bass pot’s top to its wiper. With the Bass turned down it still passes the treble.
- Bass 2 1M, 1 MΩ pot, audio taper
- Bass, 1 MΩ. Its wiper is the Volume’s top. Turned up, the wiper nears the top lug and the lows come straight through. Turned down, more of the track is in series and only the .0015 µF passes. Audio taper and more bass clockwise are assumed.
- .006µ, 6 nF
- From the Bass wiper to the Bass pot’s bottom lug.
- 100k, 100 kΩ
- The bottom of the tone network, 100 kΩ to ground.
- Vol 2 1M, 1 MΩ pot, audio taper
- Volume 2, 1 MΩ. Its wiper feeds the mixing node through 330 kΩ. Audio taper is assumed.
- 330k, 330 kΩ
- Mixing resistor from Volume 2’s wiper to V2a’s grid.
- 1.5k, 1.5 kΩ
- Cathode resistor shared by both halves of V1 (+1 V on the drawing).
- 25µ, 25 µF electrolytic
- Bypass for V1’s shared cathode, full gain down to a few hertz.
- .0022µ, 2.2 nF
- From channel 2’s tone network input to the reverb driver. With the 1 MΩ it passes little under about 70 Hz.
- 1M, 1 MΩ
- Grid resistor for V3a.
- V3a, 6CG7
- Half a 6FQ7 (or 6CG7), the first half of the reverb driver. Its plate drives one side of the unit’s input element.
- V3b, 6CG7
- The other half. Its grid gets a small part of V3a’s output, and its plate swings the opposite way, so it drives the other side of the input element.
- 820, 820 Ω
- The two driver halves’ shared cathode resistor, not bypassed (+6.2 V on the drawing).
- 27k, 27 kΩ
- Plate resistor for V3a, from the 280 V node (+180 V on the plate).
- 27k, 27 kΩ
- Plate resistor for V3b, the same.
- .01µ, 10 nF
- From V3a’s plate to one side of the input element.
- .01µ, 10 nF
- From V3b’s plate to the other side of the input element.
- 1M, 1 MΩ
- Top of V3b’s grid divider, from C22’s far side.
- 150k, 150 kΩ
- Bottom of V3b’s grid divider. With R25 it feeds V3b about an eighth of V3a’s swing, which V3b brings back up, inverted.
- Unit in, 1 nF
- The reverb unit’s input element, a crystal driven from both sides. Its capacitance, 1 nF, is typical, not on the drawing.
- 10M, 10 MΩ
- Not a real part: a 10 MΩ across the input element, so the current in it follows the element’s voltage. That current drives the springs, which are played back from a recording of how a measured tank rings.
- Unit out, 1 nF
- The reverb unit’s output element, a crystal. The springs’ signal comes out through its own capacitance, 1 nF, typical. At 160 Hz that’s about 1 MΩ, so the Reverb pot thins out the lows.
- Unit out L, 1 µH
- Not a real part: where the springs’ signal comes in, in series with the output element.
- Unit out R, 1 Ω
- Not a real part: the bottom of the output element’s leg. The springs’ level is assumed. It is set so the springs sit as far under a picked note as on the Silvertone 1484, which has the same kind of unit.
- Reverb 1M, 1 MΩ pot, audio taper
- Reverb, 1 MΩ, across the unit’s output. Its wiper feeds the mixing node through 2.2 MΩ, so it sets how much reverb joins the dry signal. Audio taper is assumed.
- 2.2M, 2.2 MΩ
- From the Reverb wiper to V2a’s grid, the mixing node.
- V4a, 12AX7 / ECC83 / 7025
- Half of V4, a 12AX7, the vibrato’s oscillator. A ladder of three caps from its plate back to its grid turns the plate’s swing round by half a cycle at a few hertz, so the stage oscillates there.
- 330k, 330 kΩ
- The oscillator’s plate resistor, from B+ (320 V on the drawing).
- .02µ, 20 nF
- First cap of the ladder, from the oscillator’s plate.
- Speed 1M, 1 MΩ pot, linear taper
- Vib Speed, 1 MΩ, a variable resistor from the ladder’s first node toward ground through 68 kΩ. Turned up, there’s less track in the circuit and the oscillator runs faster. Linear taper and faster clockwise are assumed.
- 68k, 68 kΩ
- The fixed 68 kΩ under the Speed pot. It sets the top speed.
- .01µ, 10 nF
- Second cap of the ladder.
- 560k, 560 kΩ
- The ladder’s second leg, to ground.
- .01µ, 10 nF
- Last cap of the ladder, into the oscillator’s grid.
- 2.2M, 2.2 MΩ
- The oscillator’s grid leak, 2.2 MΩ to ground.
- Cathode tap, 1 V
- Not a real part: the oscillator’s cathode is on the output tubes’ cathode resistors, at the top of the 18 Ω under the 100 Ω. Their idle current puts about 1.5 V there (1.7 V on the drawing). This source behind 18 Ω stands in for that, set to what the whole amp idles at.
- .05µ, 50 nF
- Couples the oscillator’s swing from its plate to the Strength pot.
- 560k, 560 kΩ
- With the Strength pot below it, it cuts the oscillator’s swing down for the lamp driver. Its value isn’t marked on the drawing, so the Silvertone 1484’s 560 kΩ in the same place is assumed.
- Strength 1M, 1 MΩ pot, linear taper
- Vib Strength, 1 MΩ, to ground. Its wiper feeds the lamp driver’s grid through 1 MΩ. Turned up, more of the swing reaches the grid and the lamp flashes harder. Linear taper and more clockwise are assumed.
- 1M, 1 MΩ
- From the Strength wiper to the lamp driver’s grid.
- .1µ, 100 nF
- From the lamp driver’s grid to ground. With the 1 MΩ it rounds the oscillator’s swing off above about 1.6 Hz.
- V4b, 12AX7 / ECC83 / 7025
- The other half of V4, the lamp driver. Its cathode is held a couple of volts up, so it barely conducts at rest and its plate current flashes the lamp on each upswing.
- 27k, 27 kΩ
- The lamp driver’s cathode resistor to ground.
- 2.2M, 2.2 MΩ
- From the 220 V node to the lamp driver’s cathode, 2.2 MΩ 1 W. With the 27 kΩ it holds the cathode about 2.7 V up, near cutoff (1.8 V on the drawing, read with a meter that loads this node).
- Neon, NE-2 neon
- The lamp in the vibrato unit (306-2H), from the 220 V node to the lamp driver’s plate. The figures are typical of an NE-2 neon. It strikes at about 76 V and once lit holds about 58 V, and its light follows its current.
- LDR, Ampeg TM-1 cell
- The photocell in the vibrato unit, from channel 2’s tone network (after the two 220 kΩ resistors) to ground. Lit, it pulls channel 2 down, so the vibrato works on channel 2 only. The unit’s cell isn’t documented. A high-resistance cell of the Ampeg TM-1 kind stands in, 35 MΩ dark and 20 kΩ at the lamp’s 0.3 mA, as on the Silvertone 1484.
- V2a, 12AX7 / ECC83 / 7025
- 12AX7, the driver. A cathodyne has no gain of its own, so this stage raises the preamp’s signal about 30 times, enough to drive the output tubes. Its grid connects straight to the preamp’s output with no coupling cap, so its path to ground is through the preamp’s volume and tone network.
- 220k, 220 kΩ
- Plate resistor for the driver.
- 2.2k, 2.2 kΩ
- Cathode resistor for the driver. It sets the driver’s bias, a volt or so.
- 25µ, 25 µF electrolytic
- Bypass cap across the driver’s cathode resistor, for full gain above a few hertz.
- .01µ, 10 nF
- Coupling cap from the driver to the cathodyne.
- V2b, 12AX7 / ECC83 / 7025
- The cathodyne, or split-load inverter. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side.
- 68k, 68 kΩ
- The cathodyne’s plate resistor, the output to tube B.
- 68k, 68 kΩ
- The cathodyne’s cathode load, the same value as its plate resistor, and the output to tube A. There’s no separate bias resistor.
- 1M, 1 MΩ
- Grid resistor for the cathodyne, 1M Ω straight to its cathode, as on the drawing. With no bias resistor, the grid’s own small current through it sets the bias, a volt or so below the cathode.
- .01µ, 10 nF
- Coupling cap to tube A’s grid.
- .01µ, 10 nF
- Coupling cap to tube B’s grid.
- V5, EL84 / 6BQ5
- EL84, tube A of the push-pull pair, its cathode on the shared cathode resistor, so it biases itself.
- V6, EL84 / 6BQ5
- EL84, tube B of the pair.
- 560k, 560 kΩ
- Grid leak for tube A, to ground. The bias comes from the cathode resistor. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 560k, 560 kΩ
- Grid leak for tube B.
- 118, 118 Ω
- The shared cathode resistor. Every output tube’s current runs through it and lifts the cathodes above the grids, and that’s the bias. Driven hard, the pair draws more current on average, so the cathodes climb and the tubes run colder, which softens the clipping.
- 2.2k, 2.2 kΩ
- Dropping resistor from B+ to the screen supply. The screens sit slightly below the plates.
- 10µ, 10 µF electrolytic
- Filter cap on the screen supply.
- 27k, 27 kΩ
- Dropping resistor from the screen supply node to the node for the preamp and the inverter, as on the Danelectro DM-25 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 5µ, 5 µF electrolytic
- Filter cap at the node for the preamp and the inverter. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 8 kΩ to 8 Ω, 40 H primary, 10 mH leakage
- The output transformer, 8 kΩ plate to plate into 8 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 300 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 300 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 300 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 100 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 100 Ω
- Resistance of the other half. Typical of the part.
- V8, 6X4
- One plate of the 6X4 rectifier. It conducts near the peak of its half of the winding, and its own drop rises with the current, which adds to the sag.
- V8, 6X4
- The rectifier’s other plate, on the other half cycle.
- 20µ, 20 µF electrolytic
- The reservoir cap. It feeds the output transformer’s center tap. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 8.69 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 8 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 256 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 464 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 14.3 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 2.13 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 2.19 Ω
- Limits what Loss L2 adds.
- Tank R, 83.7 Ω
- Height of the bass resonance, about 92 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 21.1 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 220 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- Values from the factory drawing. The 6FQ7 uses the 6CG7 model, the same tube with a different heater rating. The 7189s use the EL84 model.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.