Three-transistor germanium fuzz on 3 V, 1966 style

Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.

Start here

Modeled after the Selmer Buzz Tone.

Three germanium PNP stages on a 3 V supply. A gain stage feeds the Depth pot, then two stages with collector-to-base feedback, and the last one clips into a near square wave.

Input

Add

Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.

How it’s played
Tap a part to change its value, or a wire to probe it. To add or take out parts, open Modify this circuit, below. Red numbers are DC voltages to ground, not warnings. Scroll or drag to see the whole circuit. Pinch to zoom.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.

Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.

Add a part

Tap where each leg goes. Tap both ends of a part to put the new one across that part.

Change a part

With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.

Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.

Change a wire

With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.

With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.

Keep and share

Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.

Test tone for the graphs
The graphs use a steady tone. Play sounds a plucked string that dies away.

Input

pickup, unloadedat the pedal input

Output

at the amp input

Probe

Spectrum

Frequency response

What the curves mean

The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.

Output

Bias

every voltage and current at rest

What to listen for Q1 is a gain stage of about 2. The Depth pot, wired as a variable resistor, sets how much of Q1’s signal reaches Q2. Q2 and Q3 each have a resistor from collector to base and their emitters on the positive rail, so the more signal current reaches a base, the more the collector swings. On a 200 mV pick Q1 and Q2 swing about a tenth of a volt. Q3 swings its collector from the positive rail to about 2.7 V below it, a near square wave, so Q3 does most of the clipping. The 3 V supply sets how tall that square wave is. There are no clipping diodes and no tone control.

Download.

Parts and what they do

Stock values. Tap a part on the schematic to change it.

R1, 27 kΩ
Series resistor at the input, where the guitar’s cable connects.
C1, 25 µF electrolytic
Input coupling cap.
R2, 39 kΩ
Q1’s base bias from the supply.
R3, 15 kΩ
Q1’s base bias to the positive rail.
Q1, 2N1305
First stage, a common-emitter amp.
R4, 2.2 kΩ
Q1’s collector load. The scan reads 2.2 kΩ or 8.2 kΩ. A later redraw lists 2.2 kΩ.
R5, 1 kΩ
Q1’s emitter resistor, unbypassed, so Q1’s gain is about 2.
C2, 50 µF electrolytic
Couples Q1 to the Depth pot.
Depth, 25 kΩ pot, linear taper
A 25 kΩ pot wired as a variable resistor in series with Q2’s input. Less resistance means more gain in Q2. Its taper isn’t on the drawing, so it’s set linear.
Q2, 2N1305
Second stage, its emitter straight to the positive rail.
R6, 22 kΩ
From Q2’s collector to its base. It sets Q2’s bias and, against the resistance in front of it, Q2’s gain.
R7, 1 kΩ
Q2’s collector load.
C3, 25 µF electrolytic
Couples Q2 to Q3.
Q3, 2N1305
Third stage, wired as Q2 is.
R8, 15 kΩ
From Q3’s collector to its base, for bias and gain.
R9, 1.5 kΩ
Q3’s collector load.
C4, 50 µF electrolytic
Output coupling cap.
Volume, 100 kΩ pot, audio taper
Output level, a 100 kΩ pot. Its taper isn’t on the drawing, so it’s set log.

About this version

2N2613 (2N1305)
Positive ground on 3 V. The drawing marks all three 2N2613. The library’s 2N1305, a small germanium PNP of the same years, stands in for them.

How this tool works. Every part is described by an equation, and the whole circuit is solved several times for each audio sample: 192,000 samples a second while you drag a knob, and 384,000 once you let go. Transistors use the standard Ebers-Moll model, with gain, leakage, base resistance, junction capacitance, temperature and the small rise in current with collector voltage (the Early effect). The charge a transistor stores is worked out at its idle point. That is accurate for small signals and rough while the transistor switches hard. Tubes use Koren’s equations, matched to each type’s datasheet, plus grid current. Diodes use the standard diode equation with series resistance. Presets are typical of each type. Caps are ideal, and the battery or HT is a voltage behind a resistance.

Spot an error, or want a circuit added? Email info@swellamps.com. A schematic or a clear photo of one helps. Anything you send may be used to improve these models and our desktop app.

From Swell Amplification, swellamps.com.