EF86 preamp with cathode-follower tremolo, 1961 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Vox AC4.
One EF86 stage into one EL84, single-ended. The tremolo moves the EF86’s bias. A phase shift oscillator drives a cathode follower, and the follower feeds the EF86’s cathode through 100 kΩ.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar goes into one EF86 pentode, the only gain stage, then through the volume to the EL84. The tremolo works on the EF86’s cathode. V2b is a phase shift oscillator. Three caps from its plate back to its grid turn the signal round by half a cycle at a few hertz, so it oscillates there by itself. V2a is a cathode follower on V2b’s plate. Its cathode sits near 163 V and pushes about 1.6 mA through R8 into R7, and that current is most of the EF86’s bias. As V2b’s plate swings, the EF86’s cathode moves between about 1.9 and 3.1 V, and the stage’s gain rises and falls about 16 dB. The EF86’s plate swings too, about 68 V at the tremolo’s rate, and C3 passes part of that slow swing on toward the EL84. Speed runs the oscillator from about 5.6 to 9.7 times a second. There’s no depth control. R4, 5.5 MΩ, holds the screen near 92 V, so the stage has less gain than a usual EF86 stage. The Tone is a .001 µF cap to ground through a 1 MΩ pot, brighter clockwise. The EL84 runs single-ended in cathode bias with no feedback, off an EZ80. The figures here are for the preamp on its 270 V supply.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R1, 100 kΩ
- From input 1 to the EF86’s grid.
- R2, 100 kΩ
- From input 2 to the EF86’s grid. With nothing in that jack its switch grounds the tip, so R2 goes to ground and halves the guitar’s signal with R1.
- R5, 1 MΩ
- Grid leak, 1 MΩ to ground.
- V1, EF86 / 6267
- EF86 pentode, the only gain stage ahead of the power tube. The tremolo works on its cathode.
- R6, 220 kΩ
- Plate resistor from the 260 V node. The drawing shows 215 V on the plate.
- R4, 5.5 MΩ
- Screen resistor, 5.5 MΩ as the drawing shows it. It holds the screen low, so the stage has less gain and more headroom than a usual EF86 stage.
- C1, 100 nF
- Screen bypass cap.
- R7, 1.5 kΩ
- Cathode resistor. Most of the current through it comes from V2a through R8, so it sets the EF86’s bias along with the tremolo. The drawing shows 2.7 V here.
- C2, 25 µF electrolytic
- Cathode bypass, 25 µF. It holds the cathode still for the guitar but not for the slow tremolo swing.
- R3, 22 kΩ
- Dropping resistor from the 270 V node to the EF86’s 260 V node.
- C4, 8 µF electrolytic
- Filter cap on the 260 V node.
- C3, 50 nF
- Coupling cap from the EF86’s plate to the volume.
- Volume, 1 MΩ pot, audio taper
- Volume, 1 MΩ log. Its wiper feeds the EL84’s grid through R16, and the pot is the grid’s path to ground.
- R16, 5.6 kΩ
- The EL84’s grid stopper, 5.6 kΩ, from the volume’s wiper to the grid. It keeps the power tube from oscillating.
- C11, 1 nF
- The tone cap, from the top of the volume to the Tone pot.
- Tone, 1 MΩ pot, audio taper
- Tone, 1 MΩ log, a variable resistor from C11 to ground. Counterclockwise its resistance falls and C11 cuts more treble. Clockwise is brighter, assumed, since the drawing doesn’t mark it.
- V2b, 12AX7 / ECC83 / 7025
- One half of a 12AX7, the tremolo’s oscillator. Three caps from its plate back to its grid turn the signal round by half a cycle at a few hertz, so it oscillates there by itself.
- R9, 220 kΩ
- Oscillator plate resistor from the 270 V node. The drawing shows 145 to 165 V on the plate.
- R12, 3.3 kΩ
- Oscillator cathode resistor. The drawing shows 1.7 V here.
- C5, 25 µF electrolytic
- Oscillator cathode bypass.
- C6, 20 nF
- First cap of the phase shift ladder.
- Speed, 1 MΩ pot, linear taper
- Speed, 1 MΩ, the ladder’s first leg to ground with R11 from its wiper. Clockwise the leg’s resistance falls and the oscillator runs faster. Taper assumed.
- R11, 220 kΩ
- From the Speed pot’s wiper to ground. It sets the fastest speed.
- C7, 10 nF
- Second cap of the ladder.
- R13, 1 MΩ
- The ladder’s middle leg to ground.
- R10, 10 MΩ
- From the 260 V node to the ladder’s middle, 10 MΩ. It holds that node about 24 V up.
- C8, 10 nF
- Last cap of the ladder, into the oscillator’s grid.
- R14, 1 MΩ
- The oscillator’s grid leak.
- V2a, 12AX7 / ECC83 / 7025
- The other half of the 12AX7, a cathode follower. Its grid is on the oscillator’s plate, so its cathode follows the slow swing. The drawing shows 163 V on the cathode.
- R8, 100 kΩ
- From V2a’s cathode into the EF86’s cathode. About 1.6 mA flows through it into R7, and its swing moves the EF86’s bias up and down. That is the tremolo.
- V3, EL84 / 6BQ5
- EL84, the output tube, single-ended: it carries the whole signal, and its idle current runs through the transformer all the time. Its cathode resistor biases it. Its grid connects straight to the preamp’s volume pot, which is its path to ground.
- 150, 150 Ω
- The cathode resistor. The tube’s current runs through it and lifts the cathode above the grid, and that’s the bias. Driven hard, the tube draws more current on average, so the cathode climbs and the bias goes colder.
- 25µ, 25 µF electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 1k, 1 kΩ
- Dropping resistor from the reservoir cap to B+, as on the amp’s drawing. The output transformer and the screen hang after it, so the tube’s whole current runs through it.
- 32µ, 32 µF electrolytic
- Filter cap on B+ after the dropping resistor, where the output transformer and the screen hang.
- OT, 5 kΩ to 3 Ω, 14.3 H primary, 54.3 mH leakage
- The output transformer, 5 kΩ from the plate to B+ into 3 Ω, center tap on B+ after the dropping resistor. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 250 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 250 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 250 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 100 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 100 Ω
- Resistance of the other half. Typical of the part.
- V4, EZ80
- One plate of the EZ80 rectifier. It conducts near the peak of its half of the winding, and its own drop rises with the current, which adds to the sag.
- V4, EZ80
- The rectifier’s other plate, on the other half cycle.
- 32µ, 32 µF electrolytic
- The reservoir cap. It feeds the dropping resistor, and past it the output transformer’s center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 3.26 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 3 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 96 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 174 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 5.36 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 799 µH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 821 mΩ
- Limits what Loss L2 adds.
- Tank R, 31.4 Ω
- Height of the bass resonance, about 35 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 7.92 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 587 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The EF86 preset is fitted to the data sheet. V2 is one 12AX7: the oscillator and the cathode follower.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.