Optical tube leveling amplifier, 1965 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Teletronix LA-2A Leveling Amplifier.
A light panel and a photocell in one can turn the signal down. The panel glows from the sidechain amplifier, the cell drops its resistance in the light and pulls the signal toward ground, and three tube stages make the gain back up.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The guitar reaches T1 through the DI box, which isn’t part of the unit. T1 steps the signal up ten times, and R6 and the T4’s cell divide it before Gain and V1. The sidechain listens at the R6, R7 joint, so it hears what the cell has left. V3 and the 6AQ5 drive the panel, which glows brighter the harder it’s driven, and the cell drops from over 20 MΩ toward a kilohm and pulls the signal down. Nothing rectifies the signal: the cell’s own speed sets the timing. It pulls down within about 10 ms, lets go of half in about 60 ms and the rest over a second or more, longer after heavy reduction. In Limit, R7 lets the sidechain hear part of the input too, so the output holds nearly flat; Compress shorts R7 for about 3:1. V1 and the 12BH7 follower make the level back up, about 40 dB with Gain full.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- DI in, 1 MΩ
- Not part of the unit: the DI box’s input resistance, 1 MΩ, as a guitar amp’s.
- DI box, 1 V
- Not part of the unit: a unity-gain buffer with a 50 Ω output, as a DI box or a line driver, so the guitar meets the 600 Ω input at line level.
- T1 pri R, 50 Ω
- Resistance of T1’s 600 Ω primary. A typical value.
- T1 pri, 10 H
- T1’s primary, wired for 600 Ω. 10 H is typical for a 600 Ω input winding good to 30 Hz.
- T1 sec, 1 kH
- T1’s secondary, 60 kΩ overall, ten times the primary’s turns, so the signal comes out 10 times larger.
- T1 sec R, 4 kΩ
- Resistance of T1’s secondary. A typical value.
- T1 k, coupling factor 0.9999
- Coupling between T1’s windings. Below 1, the part that misses acts as leakage inductance and cuts the top end.
- R5, 68 kΩ
- R5, 68 k across T1’s secondary. It loads the transformer to a known impedance, which keeps its response flat.
- R6, 68 kΩ
- R6, 68 k, the top of the light-controlled divider. The T4’s cell below it pulls the signal down.
- R7, 2.7 kΩ
- R7, 2.7 k between the sidechain tap and the cell. With it in, the sidechain sees about a 25th of the input even when the cell is pulled right down, so it limits. Compress shorts it.
- T4 cell, T4 signal cell
- The T4’s signal cell. Over 20 MΩ dark, a few hundred ohms in full light. Lit by the panel, it pulls the signal toward ground. It lets go of half its pull in about 60 ms and the rest over seconds, slower after heavy reduction. With a large signal across it, it bends the wave slightly, mostly into the third harmonic.
- Gain, 100 kΩ pot, audio taper
- Gain, 100 k, after the cell. It sets the output level and nothing about the reduction. Audio taper.
- Peak Reduction, 100 kΩ pot, audio taper
- Peak Reduction, 100 k, how much of the signal reaches the sidechain. Turned up, the panel lights sooner, so the reduction starts at a lower level. Audio taper.
- V1a, 12AX7 / ECC83 / 7025
- Half a 12AX7A, the first gain stage, with the overall feedback in its cathode.
- R9, 220 kΩ
- V1a’s plate resistor, 220 k from the 205 V line (115 V on the plate on the drawing).
- R10, 1.5 kΩ
- V1a’s cathode resistor, 1.5 k, unbypassed. The feedback comes in across it.
- R11, 68 kΩ
- R11, 68 k, brings the overall feedback from the output stage to V1a’s cathode.
- C1, 20 nF
- C1, .02 µF, from V1a’s plate to V1b’s grid.
- R12, 470 kΩ
- V1b’s grid resistor, 470 k.
- V1b, 12AX7 / ECC83 / 7025
- The other half of the 12AX7A, the second gain stage.
- R13, 220 kΩ
- V1b’s plate resistor, 220 k from the 205 V line (120 V on the drawing).
- R14, 2.7 kΩ
- V1b’s cathode resistor, 2.7 k, unbypassed.
- C2, 100 nF
- C2, .1 µF, from V1b’s plate to the output stage.
- V2a, 12BH7 (GE, JJ)
- The upper half of the 12BH7A, a cathode follower whose plate also drives the lower half.
- R15, 470 kΩ
- R15, 470 k from the upper grid to the output. Tied to the output, it sets the grid’s bias and barely loads V1b.
- R17, 10 kΩ
- R17, 10 k on the upper plate (220 V on the drawing). The current change through it is the signal the lower half gets.
- R18, 1 kΩ
- R18, 1 k from the upper cathode to the output.
- C3, 100 nF
- C3, .1 µF, from the upper plate to the lower grid. When the upper half draws more current the lower half draws less, so both push the output the same way.
- R19, 470 kΩ
- The lower half’s grid resistor, 470 k.
- V2b, 12BH7 (GE, JJ)
- The lower half of the 12BH7A, the active pull-down under the upper half. Together they drive the output transformer from a low impedance.
- R20, 1 kΩ
- The lower half’s cathode resistor, 1 k.
- R21, 100 kΩ
- R21, 100 k from the output stage to the feedback node: the top of the overall feedback, about 20 dB of it.
- R22, 33 kΩ
- R22, 33 k, the feedback divider’s bottom.
- C4, 200 pF
- C4, a 50 to 380 pF trimmer across R22, set at 200 pF here. It trims the feedback at the top of the range, for flat response.
- C5, 10 µF electrolytic
- C5, 10 µF, keeps the output stage’s 100 V off the output transformer, which can’t take DC.
- T2 pri R, 1.43 kΩ
- Resistance of T2’s primary, 1,430 Ω, from UTC’s catalog.
- T2 pri, 30 H
- T2’s 15 kΩ primary. 30 H is typical for a line output winding at this impedance.
- T2 sec, 1.2 H
- T2’s 600 Ω secondary, a fifth of the primary’s turns.
- T2 sec R, 60 Ω
- Resistance of T2’s secondary. A typical value.
- T2 k, coupling factor 0.9995
- Coupling between T2’s windings. Below 1, the part that misses acts as leakage inductance.
- V3a, 12AX7 / ECC83 / 7025
- Half of the sidechain’s 12AX7A. Both halves run in parallel as one stage.
- V3b, 12AX7 / ECC83 / 7025
- The other half of the 12AX7A, in parallel with the first.
- R32, 1 kΩ
- R32, 1 k between the two grids.
- R31, 1 kΩ
- The shared cathode resistor, 1 k (0.75 V on the drawing).
- C8, 30 nF
- C8, .03 µF across the cathode resistor. It bypasses only the top end, so the sidechain has more gain above about 5 kHz.
- R33, 220 kΩ
- The plate resistor, 220 k from B+.
- C9, 20 nF
- C9, .02 µF, from the sidechain amp to the stereo line.
- C6, 10 nF
- C6, .01 µF, with R30 a treble cut on the sidechain signal.
- R30, 47 kΩ
- R30, 47 k under C6.
- Lim. Resp., 1 MΩ pot, linear taper
- R37, 1 M, the rear Limit Response trim, at flat (no resistance). Turned up, it cuts the lows reaching the driver while C12 still passes the highs, so the treble is reduced more.
- C12, 1 nF
- C12, .001 µF across R37, so the highs bypass it.
- Stereo Adj., 1 MΩ pot, linear taper
- R3, 1 M, the rear Stereo Adjust trim, full on as the manual sets a single unit. It matches two units’ reduction for stereo.
- V4 6AQ5A, 6AQ5
- The 6AQ5A drives the light panel. Its plate swings over 100 V peak to light it.
- R34, 22 kΩ
- R34, 22 k 2 W, the driver’s plate resistor from B+.
- R35, 220 kΩ
- R35, 220 k from B+ to the screen.
- C7D, 30 µF electrolytic
- C7D, 30 µF, holds the screen steady.
- R36, 1 kΩ
- The driver’s cathode resistor, 1 k.
- C10, 50 µF electrolytic
- C10, 50 µF, bypasses the cathode for full gain.
- C11, 10 nF
- C11, .01 µF, keeps the plate’s DC off the panel. With the panel’s 1.8 nF it passes most of the swing.
- R8, 2.2 MΩ
- R8, 2.2 M across the panel inside the can, so no DC builds up on it.
- T4 panel, T4 light panel
- The T4’s light panel, a capacitor with phosphor in it, about 1.8 nF. It glows when the voltage across it changes, steeply brighter above a few tens of volts and brighter at higher frequencies.
- T3 a, 250 V ac, 60 Hz
- One half of T3’s 500 V center-tapped winding, as a sine at the mains frequency.
- T3 b, 250 V ac, 60 Hz
- The other half of the winding, half a cycle behind.
- T3 R, 150 Ω
- Resistance of one half of the winding. A typical value.
- T3 R, 150 Ω
- Resistance of the other half. A typical value.
- CR1, 1N4001
- One of the two silicon rectifiers (1N3196).
- CR2, 1N4001
- The other rectifier, for the other half cycle.
- C7A, 40 µF electrolytic
- C7A, 40 µF, the first filter cap.
- R29, 4.7 kΩ
- R29, 4.7 k 2 W, from the rectifier to B+.
- C7B, 40 µF electrolytic
- C7B, 40 µF, on B+ (275 V on the drawing).
- R16, 68 kΩ
- R16, 68 k from B+ to V1’s line (205 V on the drawing).
- C7C, 30 µF electrolytic
- C7C, 30 µF, filters V1’s line.
- R28, 470 kΩ
- R28, 470 k from B+, feeds the neon that holds the meter bridge’s supply.
- NE-2, NE-2 neon
- The NE-2 neon holds the meter bridge’s supply near 60 V (65 V on the drawing), so the meter’s zero doesn’t move with B+.
- Zero Adj., 1 MΩ pot, linear taper
- R4, 1 M, the meter’s zero adjust, a screwdriver control on the front panel. Its wiper takes the neon’s supply to both arms of the bridge. Set so the meter reads 0 with no signal in Gain reduction.
- R26, 330 kΩ
- R26, 330 k, across the cell’s arm of the bridge.
- R27, 10 kΩ
- R27, 10 k, in series with the meter cell.
- Meter cell, T4 signal cell
- The T4’s second photocell (pins 5 and 6), lit by the same panel as the gain cell. As its resistance falls the bridge’s cell arm drops, and the meter falls with the gain.
- R25, 18 kΩ
- R25, the bridge’s other arm, selected between 18 k and 68 k on each unit to match its T4 so the meter reads the reduction in dB. 18 k here: with both cells alike, the meter reads 9.6 dB at 10 dB of real reduction and 18.4 dB at 20.
- R24, 3.9 kΩ
- R24, 3.9 k, in series with the meter in every position: the standard series resistor that makes a VU meter read 0 at +4 dBm on a 600 Ω line.
- VU meter, 3.9 kΩ
- The VU meter’s movement and its rectifier, 3.9 kΩ, the standard figure for a VU meter. Its needle follows the average of the current, rectified, with a VU meter’s 300 ms swing. 0 VU at 141.6 µA.
- R23, 6.8 kΩ
- R23, 6.8 k, added in series in the +10 position, so the meter reads 0 VU about 6 dB higher.
About this version
- As drawn (1966)
- The factory drawing revised 7-19-66, fed unbalanced on the 600 Ω input. The T4 cell is modeled from repairers’ measurements and set to follow the manual.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.