Reverb and tremolo 25 W tube amp, 1972 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Marshall 2046 Specialist.
One channel: a 12AX7 stage, Volume and a one-knob Tone, then a second stage into a cathodyne and two EL34s. An ECL86 drives the spring tank and recovers it, and the tremolo moves the EL34s’ bias.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The Volume sits right after the first stage, so it sets how hard everything after it is driven. Tone is brighter clockwise: the 600 pF carries the treble around the 500 kΩ pot, and the .05 µF end trims the bass. The reverb is taken off the Volume’s wiper, so it follows the Volume. The ECL86’s pentode drives the tank through a transformer and its triode brings the springs back up. The Reverb pot blends the wet signal into V1b’s grid beside the dry signal. As drawn, the reverb is faint. At full Reverb it’s about 56 dB under the dry signal in the model, against about 26 dB on the bench’s Deluxe Reverb. The driver’s screen sits at about 38 V behind its 470 kΩ, and the recovery stage’s 10 kΩ cathode resistor holds its gain to about 8. The tremolo is in the power amp. It swings the EL34s’ bias a few times a second. On Preamp only, you hear the signal as it reaches the cathodyne.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R1A, 68 kΩ
- The input 1 resistor into the grid. With nothing plugged into input 2, this resistor and input 2’s resistor are in parallel, so a guitar in input 1 goes through 34 kΩ to the grid. That is enough to stop radio pickup and too little to cut treble.
- R1B, 68 kΩ
- The input 2 resistor into the grid. With nothing plugged into input 1, input 1’s tip is grounded, and the two 68 kΩ resistors form a divider. Input 2 is about 6 dB quieter and loads the guitar with 136 kΩ.
- RG1, 1 MΩ
- Input 1’s 1 MΩ to ground. It sets the load a guitar in input 1 sees, and with a patch lead in input 1 it is the end of the lead’s path.
- 10k, 10 kΩ
- Dropping resistor, 10 kΩ 1 W, from node A (V1b and the cathodyne) to V1a’s node.
- 32µ, 32 µF electrolytic
- Filter cap on V1a’s node. The recovery stage hangs here too.
- V1a, 12AX7 / ECC83 / 7025
- The first gain stage.
- 220k, 220 kΩ
- V1a’s plate resistor, 220 kΩ. The higher value raises the stage’s gain and lowers its current.
- 820, 820 Ω
- V1a’s cathode resistor.
- 25µ, 25 µF electrolytic
- V1a’s bypass cap. With it the stage has full gain down through the bass.
- .022µ, 22 nF
- Coupling cap to the Volume.
- Volume, 1 MΩ pot, audio taper
- Volume, 1 MΩ. Its wiper feeds the tone network and the reverb driver.
- 22k, 22 kΩ
- From the Volume’s wiper to the top of the Tone pot.
- Tone, 500 kΩ pot, linear taper
- Tone, 500 kΩ. Clockwise, the wiper moves to the .05 µF end, so the bass is trimmed and the treble comes through the 600 pF. Counterclockwise, the wiper is near the 22 kΩ and the response is flatter and darker. Clockwise also costs a lot of level, about 12 dB from noon to full, since the .05 µF end is close to ground.
- .05µ, 50 nF
- From the bottom of the Tone pot to ground.
- 600p, 600 pF
- From the Volume’s wiper to the Tone wiper. It carries the treble around the Tone pot.
- 1M, 1 MΩ
- From the Tone wiper to V1b’s grid, the dry path. With the Reverb pot below it, it sets how much dry signal reaches V1b.
- Reverb, 500 kΩ pot, linear taper
- Reverb, 500 kΩ from V1b’s grid to ground. The wet signal comes in at the wiper through 1 MΩ. At 0 the wiper is grounded and there is no reverb. Turned up, more of the wet signal reaches the grid.
- V1b, 12AX7 / ECC83 / 7025
- The second gain stage. It mixes the dry and wet signals and drives the cathodyne.
- 100k, 100 kΩ
- V1b’s plate resistor, from node A.
- 1k5, 1.5 kΩ
- V1b’s cathode resistor.
- 25µ, 25 µF electrolytic
- V1b’s bypass cap.
- .022µ, 22 nF
- Coupling cap into the cathodyne’s grid.
- 10k, 10 kΩ
- Grid stopper into the reverb driver. Its grid’s path to ground is the Volume pot.
- V3a, 6GW8
- The ECL86’s pentode, the reverb driver. It drives the tank’s low-impedance coil through the transformer.
- 180, 180 Ω
- The driver’s cathode resistor.
- 25µ, 25 µF electrolytic
- The driver’s bypass cap.
- 470k, 470 kΩ
- The driver’s screen resistor, 470 kΩ, with no cap on the screen. The screen runs low and it holds the pentode’s current down.
- T3, 22.5 kΩ to 8 Ω, 20 H primary, 50 mH leakage
- The reverb transformer. It steps the driver’s plate down to the tank’s 8 Ω input coil. Its figures are typical of the part.
- Tank in R, 800 mΩ
- Resistance of the tank’s input coil, 0.8 Ω, measured on a long tank. The current through this coil drives the springs, which play from a measured tank’s impulse response.
- Tank in L, 1.1 mH
- Inductance of the tank’s input coil, 1.1 mH, measured on a long tank.
- Tank out L, 350 mH
- The tank’s output coil, 0.35 H, from the recovery stage’s grid to ground. The springs come back in series with it. It is also the grid’s only path to ground. Measured on a long tank.
- Tank out R, 181 Ω
- Resistance of the tank’s output coil, 181 Ω, measured on a long tank.
- V3b, 6GW8 (triode section)
- The ECL86’s triode, the reverb recovery stage.
- 10k, 10 kΩ
- The recovery stage’s cathode resistor, 10 kΩ and not bypassed. It biases the triode cold and holds its gain to about 8.
- 100k, 100 kΩ
- The recovery stage’s plate resistor, from V1a’s node.
- .02µ, 20 nF
- Coupling cap out of the recovery stage.
- 1M, 1 MΩ
- Feeds the wet signal into the Reverb pot’s wiper.
- 1k5, 1.5 kΩ
- Dropping resistor, 1.5 kΩ 5 W, from the reservoir to the reverb driver’s node.
- 32µ, 32 µF electrolytic
- Filter cap on the reverb driver’s node.
- V4, 12AX7 / ECC83 / 7025
- 12AX7, a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 100k, 100 kΩ
- The cathodyne’s plate resistor, the output to tube B.
- 1k, 1 kΩ
- The cathodyne’s bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 100k, 100 kΩ
- The cathodyne’s cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470 kΩ
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathode’s high DC voltage. It’s the grid’s only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ω.
- .022µ, 22 nF
- Coupling cap to tube A’s grid.
- .022µ, 22 nF
- Coupling cap to tube B’s grid.
- V5, EL34 / 6CA7
- EL34, tube A of the push-pull pair, cathode grounded, biased from the fixed bias supply.
- V6, EL34 / 6CA7
- EL34, tube B of the pair.
- 220k, 220 kΩ
- Grid leak for tube A, returned to the bias supply. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 220k, 220 kΩ
- Grid leak for tube B.
- 1.5k, 1.5 kΩ
- Dropping resistor from B+ to the screen supply. The screens sit slightly below the plates.
- 50µ, 50 µF electrolytic
- Filter cap on the screen supply.
- 22k, 22 kΩ
- Dropping resistor from the screen supply node to the node for the inverter and the preamp, as on the Marshall 2046 Specialist drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 32µ, 32 µF electrolytic
- Filter cap at the node for the inverter and the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 4 kΩ to 16 Ω, 30 H primary, 10 mH leakage
- The output transformer, 4 kΩ plate to plate into 16 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 275 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 275 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 275 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 40 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 40 Ω
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 50µ, 50 µF electrolytic
- The reservoir cap. It feeds the output transformer’s center tap. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Bias tap, 30 V ac, 60 Hz
- The power transformer’s bias tap, 30 V ac, as a sine source at the mains frequency. Typical of the part.
- 1k, 1 kΩ
- Series resistor into the bias rectifier, 1k Ω. It limits the charging current.
- Bias diode, 1N4001
- The bias rectifier, a silicon diode turned so the supply comes out negative.
- 100µ, 100 µF electrolytic
- Filter cap on the bias supply, its plus side to ground. It also holds the Intensity pot’s bias end still, so the LFO swings the wiper.
- 33k, 33 kΩ
- The bias supply’s load, 33k Ω to ground. With the 1k Ω above it, it sets the bias. There’s no bias pot, so change this resistor to change the bias. Bigger runs the tubes colder.
- V8, 12AX7 / ECC83 / 7025
- The tremolo’s oscillator, half a 12AX7. The three caps after its plate turn the signal around at one frequency, and the oscillator runs at that frequency, a few times a second. In the amp it’s the other half of V2, the cathodyne’s tube.
- 220k, 220 kΩ
- Oscillator plate resistor, from the screen supply.
- 1.5k, 1.5 kΩ
- Oscillator cathode resistor.
- 25µ, 25 µF electrolytic
- Oscillator bypass cap. At a few hertz it isn’t a full short, and it adds some of the phase shift that keeps the loop oscillating.
- .022µ, 22 nF
- First ladder cap.
- Speed, 1 MΩ pot, linear taper
- Speed, 1M Ω linear, used as a variable resistor. Less resistance runs the oscillator faster.
- 220k, 220 kΩ
- Sets the top speed. It’s all that’s left with Speed on 10.
- .01µ, 10 nF
- Second ladder cap.
- 1.8M, 1.8 MΩ
- Middle resistor of the ladder, returned to the cathode. The footswitch grounds this point.
- .01µ, 10 nF
- Third ladder cap.
- 1.8M, 1.8 MΩ
- Oscillator grid leak.
- 1M, 1 MΩ
- Couples the LFO from the oscillator’s plate. It keeps the bias network from loading the oscillator much.
- .1µ, 100 nF
- Blocks the oscillator’s DC, so only its swing reaches the Intensity pot.
- Intensity, 500 kΩ pot, linear taper
- Intensity, 500k Ω linear. One end gets the LFO, the other sits on the bias supply, and the wiper is the bias line for both output tubes. At 0 the wiper is on the bias supply and the bias holds still. Turned up, more of the LFO rides on the bias, so both grids move together and the output stage’s gain rises and falls. Which way it turns isn’t marked on the drawing. Up is assumed to be more.
- 1µ, 1 µF
- On the bias line, to ground. With the Intensity pot it rounds off the LFO slightly.
- Coil R, 17.4 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 16 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 512 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 928 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 28.6 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 4.26 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 4.38 Ω
- Limits what Loss L2 adds.
- Tank R, 167 Ω
- Height of the bass resonance, about 185 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 42.2 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 110 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- ECC83 and ECL86
- The two gain stages are an ECC83 (12AX7) and the reverb stages an ECL86, as on the drawing. The ECL86’s halves are modeled as an EL84 and half a 12AX7.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.