Two-transistor, op-amp distortion with germanium diodes in series and a gyrator Hi control, 1984 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the DOD FX56 American Metal.
A JFET buffer and two transistor gain stages, then an op-amp with diodes in its feedback and a second path through the Distortion pot. Germanium diodes in series and silicon diodes to ground follow. An op-amp EQ stage lifts the bass near 87 Hz all the time, and Hi cuts or boosts two tuned bands near 870 Hz and 1.3 kHz.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 buffers the guitar. Q6 and Q7 are two gain stages in a row, each with a 470 kΞ© feedback resistor against a 22 kΞ© input resistor, about 44 dB together at 1 kHz, so Q7 clips on most notes. Q7βs collector feeds U1Aβs plus input. Distortion has its wiper grounded. Turned down, it loads Q6βs collector through 200 Ξ©, so less signal reaches Q7, and it puts more resistance in U1Aβs gain leg. Turned up, both of those go the other way. U1A clips with one silicon diode one way and two the other. The two 1N34A germanium diodes in series after it pass little signal under a few tens of millivolts, so they only matter as a note dies away. The silicon pair to ground clips whatβs left. The EQ stageβs 87 Hz branch sits on its minus input all the time, so the bass there comes up about 20 dB. Hi moves the other two branches from the plus side, a cut, to the minus side, a boost. The model leaves out the electronic bypass.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 10k, 10βkΞ©
- Top of the 4.5 V reference divider.
- 10k, 10βkΞ©
- Bottom of the reference divider.
- 47Β΅F, 47βΒ΅F electrolytic
- Filters the 4.5 V reference.
- 10k, 10βkΞ©
- Input series resistor.
- .047, 47βnF
- Input coupling cap.
- 1M, 1βMΞ©
- Biases Q1βs gate at 4.5 V and sets the input impedance near 1 MΞ©.
- Q1, J113
- Input buffer, a J113 source follower.
- 10k, 10βkΞ©
- Q1βs source resistor.
- 1Β΅F, 1βΒ΅F electrolytic
- Coupling cap toward the gain stages. Q4, a JFET switch after it, is drawn as a wire.
- 1M, 1βMΞ©
- Holds the switchβs line at 4.5 V. Its twin on the other side of Q4 is left out.
- .047, 47βnF
- Coupling cap into Q6.
- 22k, 22βkΞ©
- Q6βs input resistor. With the 470 kΞ© it sets Q6βs gain.
- 100k, 100βkΞ©
- From Q6βs base to ground. With the 470 kΞ© it sets Q6βs bias.
- 470k, 470βkΞ©
- From Q6βs collector to its base. It biases Q6 and sets its gain against the 22 kΞ©.
- 120pF, 120βpF
- Across the 470 kΞ©. It rolls off Q6βs gain above about 2.8 kHz.
- Q6, 2N5089
- First gain stage, a 2N5089 with its collector fed back to its base.
- 10Ξ©, 10βΞ©
- Q6βs emitter resistor.
- 10k, 10βkΞ©
- Q6βs collector resistor.
- 1k, 1βkΞ©
- Feeds the gain stagesβ own 9 V line.
- 47Β΅F, 47βΒ΅F electrolytic
- Filters the gain stagesβ 9 V line.
- .047, 47βnF
- Coupling cap into Q7.
- 22k, 22βkΞ©
- Q7βs input resistor. With the 470 kΞ© it sets Q7βs gain.
- 100k, 100βkΞ©
- From the 9 V line to Q7βs base.
- 470k, 470βkΞ©
- From Q7βs collector to its base. It biases Q7 and sets its gain against the 22 kΞ©.
- 120pF, 120βpF
- Across the 470 kΞ©. It rolls off Q7βs gain above about 2.8 kHz.
- Q7, 2N3906
- Second gain stage, a 2N3906 (PNP) with its collector fed back to its base.
- 100Ξ©, 100βΞ©
- Q7βs emitter resistor.
- 62k, 62βkΞ©
- Q7βs collector load to 9 V, with the 10 kΞ© to ground.
- 10k, 10βkΞ©
- Q7βs collector load to ground. It also sets U1Aβs DC level.
- 200Ξ©, 200βΞ©
- From Q6βs collector to the Distortion pot. With the pot turned down it loads Q6 heavily.
- 10Β΅F, 10βΒ΅F electrolytic
- Coupling cap to the Distortion pot.
- Dist., 100βkΞ© pot, linear taper
- Distortion, 100 kΞ© with its wiper to ground. The part toward Q6 loads Q6βs collector, and the part toward U1A is in U1Aβs gain leg. Turned up, Q6 is loaded less and U1Aβs gain rises from about 2.5 to about 5.7.
- 47k, 47βkΞ©
- The least resistance in U1Aβs gain leg.
- .047, 47βnF
- In series with U1Aβs gain leg, so its DC gain is 1.
- U1A, TL022
- Third gain stage, non-inverting, with diodes across its feedback.
- 220k, 220βkΞ©
- U1Aβs feedback resistor.
- 120pF, 120βpF
- Across the feedback. It rolls off the top of the clipped signal.
- 1N4148 x3, 2 Γ 1N914 / 1N4148 one way, 1N914 / 1N4148 the other way
- Three 1N4148s across U1Aβs feedback, two in series one way and one the other, so it clips unevenly.
- 1Β΅F, 1βΒ΅F electrolytic
- Coupling cap out of U1A.
- 10k, 10βkΞ©
- Into the germanium diodes.
- 1N34A x2, 1N34A germanium, one each way
- Two 1N34A germanium diodes back to back in series with the signal. They pass little signal under a few tens of millivolts, so the quietest part of a note drops out.
- 10k, 10βkΞ©
- From the germanium diodes to the silicon diodes.
- 1N4148 x2, 1N914 / 1N4148, one each way
- Two 1N4148s back to back to ground. They hold the signal to about 0.6 V either way.
- .001, 1βnF
- Across the diodes. With the 10 kΞ© it trims the treble above about 16 kHz.
- 1Β΅F, 1βΒ΅F electrolytic
- Coupling cap into U1B.
- 62k, 62βkΞ©
- Biases U1Bβs plus input at 4.5 V.
- U1B, TL022
- Buffer, a follower, to drive the EQ stage.
- 33k, 33βkΞ©
- Into the EQ stageβs plus input. The branches on the plus side cut against it.
- U2A, TL022
- EQ stage. A tuned branch on its minus input boosts its band, one on its plus input cuts it.
- Hi, 100βkΞ© pot, linear taper
- Hi, 100 kΞ©, between U2Aβs two inputs. Its wiper feeds the 870 Hz and 1.3 kHz branches. Turned up, toward the minus input, they boost. Turned down, they cut.
- 33k, 33βkΞ©
- U2Aβs feedback resistor.
- 120pF, 120βpF
- Across the feedback. It rolls off above about 40 kHz.
- .015, 15βnF
- Tunes the 870 Hz branch with the simulated inductor.
- 3.3k, 3.3βkΞ©
- The branchβs resistance. It sets how far the band can be boosted or cut.
- 680pF, 680βpF
- With the 1 MΞ© and 3.3 kΞ©, it makes U2B act as a 2.2 H inductor.
- 1M, 1βMΞ©
- Biases U2B at 4.5 V.
- U2B, TL022
- Follower of the 870 Hz branchβs simulated inductor (a gyrator).
- .01, 10βnF
- Tunes the 1.3 kHz branch with the simulated inductor.
- 3.3k, 3.3βkΞ©
- The branchβs resistance. It sets how far the band can be boosted or cut.
- 470pF, 470βpF
- With the 1 MΞ© and 3.3 kΞ©, it makes U3B act as a 1.6 H inductor.
- 1M, 1βMΞ©
- Biases U3B at 4.5 V.
- U3B, TL022
- Follower of the 1.3 kHz branchβs simulated inductor (a gyrator).
- .15, 150βnF
- Tunes the 87 Hz branch with the simulated inductor.
- 3.3k, 3.3βkΞ©
- The branchβs resistance. With the 33 kΞ© feedback it sets the bass boost near 20 dB.
- .0068, 6.8βnF
- With the 1 MΞ© and 3.3 kΞ©, it makes U3A act as a 22 H inductor.
- 1M, 1βMΞ©
- Biases U3A at 4.5 V.
- U3A, TL022
- Follower of the 87 Hz branchβs simulated inductor (a gyrator). The branch is on U2Aβs minus input, so it always boosts.
- 10Β΅F, 10βΒ΅F electrolytic
- Coupling cap out of the EQ stage.
- 100k, 100βkΞ©
- In series ahead of Level, so Levelβs top is half the EQ stageβs output.
- Level, 100βkΞ© pot, audio taper
- Level, 100 kΞ©, to ground.
- 1Β΅F, 1βΒ΅F electrolytic
- Coupling cap from Level. Q8, a JFET switch after it, is drawn as a wire.
- 1M, 1βMΞ©
- Holds the switchβs line at 4.5 V. Its twin on the other side of Q8 is left out.
- .047, 47βnF
- Coupling cap into Q3.
- 470k, 470βkΞ©
- Biases Q3βs base at 4.5 V.
- Q3, 2N5089
- Output buffer, a 2N5089 emitter follower.
- 10k, 10βkΞ©
- Q3βs emitter resistor.
- 1k, 1βkΞ©
- In series at the output.
- 1Β΅F, 1βΒ΅F electrolytic
- Output coupling cap.
- 100k, 100βkΞ©
- Output pulldown.
About this version
- Factory values
- The factory drawing dated October 1984. J113 JFETs, 2N5089 and 2N3906 transistors, TL022 op-amps. The pot tapers arenβt on the drawing: Distortion and Hi are set linear, Level audio.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.