Bass amp with a twin-T bass control and two 6L6s, 1963 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Gibson Atlas IV.
Two 6EU7 stages with a twin-T Bass control on a three-section pot between them, a Treble control, then a cathodyne into a 6EU7 driver pair and two 6L6s in fixed bias. A .047 Β΅F cap on each plate cuts the treble at the speaker.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The Bass control is a twin-T. Two paths run side by side from V1A to the Volume pot. One is two .0047 Β΅F caps in series with a pot section to ground between them, and it passes treble. The other is two pot sections and two 330 kΞ© in series with .01 Β΅F to ground in the middle, and it passes bass. All three sections turn together. From 0 to full, all three resistances rise, and the network passes about 17 dB more at 100 Hz and about 3 dB more at 1 kHz. A 3 MΞ© across the whole network keeps some signal coming through at any setting. Treble is a variable resistor in series with .022 Β΅F to ground from between two 100 kΞ©. The power amp is a cathodyne into a pair of 6EU7 drivers on one cathode resistor, into two 6L6s with no feedback. The .047 Β΅F from each plate to ground rolls off the treble above about 1 kHz.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R1, 100βkΞ©
- The jackβs 100 kΞ© to V1Aβs grid (R1 for J1, R3 for J2, the same value).
- 100k, 100βkΞ©
- The other jackβs 100 kΞ©. With nothing plugged into that jack its switch grounds its tip, so this resistor goes from the grid to ground and the input is a 100 kΞ© / 100 kΞ© divider, about 6 dB down.
- 1M, 1βMΞ©
- Grid resistor for V1A.
- 50p, 50βpF
- From V1Aβs grid to its plate. The stageβs gain makes it look like about 2,000 pF at the grid, so with the 100 kΞ© ahead of it the treble rolls off above about 1.5 kHz.
- V1A, 6EU7
- One half of a 6EU7, the input stage, cathode bypassed.
- 100k, 100βkΞ©
- Plate resistor for V1A. The drawing reads +195 V on the plate.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V1A, +1.4 V on the drawing.
- 20Β΅, 20βΒ΅F electrolytic
- Bypass for V1Aβs cathode resistor.
- .047Β΅, 47βnF
- Coupling cap into the Bass network.
- 3M, 3βMΞ©
- Straight across the Bass network, so some signal always gets through.
- .0047Β΅, 4.7βnF
- First cap of the treble path through the network.
- .0047Β΅, 4.7βnF
- Second cap of the treble path.
- 150k, 150βkΞ©
- From between the two caps to the potβs middle section, so that leg never drops below 150 kΞ©.
- Bass B 500k, 500βkΞ© pot, linear taper
- The Bass potβs middle section, 500 kΞ© linear, a variable resistor from the treble path to ground. It turns with Bass. Turned down, its resistance drops and more of the treble path goes to ground.
- Bass 1M, 1βMΞ© pot, linear taper
- Bass, the potβs first section, 1 MΞ© linear, a variable resistor at the start of the bass path, and the knob for all three sections. Turned up, the three resistances rise and the network passes more bass.
- 330k, 330βkΞ©
- First 330 kΞ© of the bass path.
- .01Β΅, 10βnF
- From the middle of the bass path to ground. It bleeds the treble out of that path.
- 330k, 330βkΞ©
- Second 330 kΞ© of the bass path.
- Bass C 1M, 1βMΞ© pot, linear taper
- The Bass potβs third section, 1 MΞ© linear, a variable resistor at the end of the bass path. It turns with Bass.
- Vol 500k, 500βkΞ© pot, audio taper
- Volume, 500 kΞ© audio. Its wiper is V1Bβs grid.
- V1B, 6EU7
- The other half of the 6EU7, the second stage. Its cathode resistor isnβt bypassed, so its gain is lower.
- 100k, 100βkΞ©
- Plate resistor for V1B, +190 V on the drawing.
- 1.5k, 1.5βkΞ©
- Cathode resistor for V1B, not bypassed, +1.4 V on the drawing.
- .0022Β΅, 2.2βnF
- Coupling cap into the Treble network. Itβs small, so it trims the deepest lows.
- 100k, 100βkΞ©
- First 100 kΞ© on the way to the cathodyne.
- 100k, 100βkΞ©
- Second 100 kΞ©, into the cathodyneβs grid.
- 100p, 100βpF
- Across R14 and R15, the trebleβs way around them.
- .022Β΅, 22βnF
- From between R14 and R15 to the Treble pot.
- Treble 50k, 50βkΞ© pot, audio taper
- Treble, 50 kΞ© audio, a variable resistor from C9 to ground. Turned down, its resistance drops and C9 bleeds the treble away. Turned up, thereβs more resistance in the way and the treble comes back.
- .047Β΅, 47βnF
- From V4βs plate to ground. Against the output transformerβs load it rolls off the treble above about 1 kHz.
- .047Β΅, 47βnF
- From V5βs plate to ground, as C14.
- V2, 6EU7
- 6EU7, a cathodyne, or split-load inverter, with no driver ahead of it. The same current runs through its plate resistor and its cathode resistors, which are about equal, so the plate swings one way and the cathode the other by about the same amount. The cathode drives tube A, the plate tube B. Its gain is slightly under 1 on each side, so the preamp has to bring the whole swing the output tubes need.
- 56k, 56βkΞ©
- The cathodyneβs plate resistor, the output to tube B.
- 2.2k, 2.2βkΞ©
- The cathodyneβs bias resistor. The grid returns below it, so the cathode sits this far above the grid.
- 56k, 56βkΞ©
- The cathodyneβs cathode load, the same value as its plate resistor. The cathode above the bias resistor is the output to tube A.
- 470k, 470βkΞ©
- Grid resistor for the cathodyne, returned to the junction of its cathode resistors so the grid sits near the cathodeβs high DC voltage. Itβs the gridβs only path to ground, and the cathode follows the grid, so the preamp sees much more than 470k Ξ©.
- .022Β΅, 22βnF
- Coupling cap from the inverter to side Aβs driver.
- .022Β΅, 22βnF
- Coupling cap from the inverter to side Bβs driver.
- 680, 680βΞ©
- The driversβ cathode resistor, 680 Ξ© to ground for both halves, with no bypass cap. The two cathodes share it, so the pair works somewhat like a long-tail pair: what one half gains in current the other loses, which evens out the two sidesβ swings.
- 220k, 220βkΞ©
- Grid leak for side Aβs driver, to ground.
- V3, 6EU7
- 6EU7, side Aβs driver: a gain stage that raises the inverterβs signal about 45 times on its way to tube Aβs grids. The other half drives side B, and the two share one cathode resistor.
- 100k, 100βkΞ©
- The driverβs plate resistor, 100k Ξ© from the node for the drivers.
- .047Β΅, 47βnF
- Coupling cap from the driverβs plate to tube Aβs grids.
- 220k, 220βkΞ©
- Grid leak for side Bβs driver, to ground.
- V3, 6EU7
- The other half of the 6EU7, side Bβs driver.
- 100k, 100βkΞ©
- The driverβs plate resistor, 100k Ξ© from the node for the drivers.
- .047Β΅, 47βnF
- Coupling cap from the driverβs plate to tube Bβs grids.
- 1.5k, 1.5βkΞ©
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current.
- 1.5k, 1.5βkΞ©
- Grid stopper for tube B.
- V4, 6L6GC
- 6L6GC, tube A of the push-pull pair, cathode grounded, biased from the fixed bias supply.
- V5, 6L6GC
- 6L6GC, tube B of the pair.
- 100k, 100βkΞ©
- Grid leak for tube A, returned to the bias supply. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. Thatβs blocking distortion.
- 100k, 100βkΞ©
- Grid leak for tube B.
- 470, 470βΞ©
- Screen resistor for tube A. It limits the screen current when the tube is driven hard.
- 470, 470βΞ©
- Screen resistor for tube B.
- 3 H, 3βH
- The choke from the reservoir cap to B+, as on the ampβs drawing. The output transformerβs center tap, the screens and everything after them hang past it, so all of their current runs through it. It passes DC with little drop. With the cap after it, it would filter ripple, but ripple isnβt modeled here. Typical of the part.
- 30, 30βΞ©
- The chokeβs winding resistance, typical. With the output tubesβ whole current through it, itβs most of the DC drop between the reservoir and B+.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap on B+ after the choke, where the output transformerβs center tap and the screens hang.
- 27k, 27βkΞ©
- Dropping resistor from the screen supply node to the node for the drivers, as on the Gibson Atlas IV drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the drivers. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- 10k, 10βkΞ©
- Dropping resistor from the node for the drivers to the node for the inverter and preamp, as on the Gibson Atlas IV drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 20Β΅, 20βΒ΅F electrolytic
- Filter cap at the node for the inverter and preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 6.6βkΞ© to 16βΞ©, 40βH primary, 10βmH leakage
- The output transformer, 6.6 kΞ© plate to plate into 16 Ξ©, center tap on B+ after the choke. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 356 V ac, 60 Hz
- One half of the power transformerβs high-voltage winding, 356 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 356 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 60βΞ©
- Resistance of one half of the winding, plus the primaryβs share. With the rectifierβs own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 60βΞ©
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 20Β΅, 20βΒ΅F electrolytic
- The reservoir cap. It feeds the choke, and past it the output transformerβs center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Bias tap, 51 V ac, 60 Hz
- The power transformerβs bias tap, 51 V ac, as a sine source at the mains frequency. Typical of the part.
- tap R, 100βΞ©
- The bias tapβs own resistance, 100 Ξ©, typical. The drawing has no resistor between the tap and the diode.
- Bias diode, 1N4001
- The bias rectifier, a silicon diode turned so the supply comes out negative.
- 10Β΅, 10βΒ΅F electrolytic
- Filter cap on the bias supply, its plus side to ground.
- 7.5k, 7.5βkΞ©
- Second resistor of the bias supply, 7.5k Ξ© to the bias line. With the cap after it, it filters the ripple a second time.
- 10Β΅, 10βΒ΅F electrolytic
- Second filter cap, on the bias line, its plus side to ground.
- 22k, 22βkΞ©
- From the bias line to ground, 22k Ξ©. With the 7.5k Ξ© above it, it divides the supply down to the bias. Thereβs no bias pot, so change this resistor to change the bias. Bigger runs the tubes colder.
- Coil R, 17.4βΞ©
- Voice coil resistance, the floor of the speakerβs impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ξ© peak near 74 Hz on 8 Ξ©), scaled to the 16 Ξ© tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 512βΒ΅H
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 928βΒ΅H
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 28.6βΞ©
- Limits what Loss L adds to the treble rise.
- Loss L2, 4.26βmH
- A second step in the treble rise, with Loss R2 across it: a real voice coilβs losses keep climbing from a few hundred hertz.
- Loss R2, 4.38βΞ©
- Limits what Loss L2 adds.
- Tank R, 167βΞ©
- Height of the bass resonance, about 185 Ξ© in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 42.2βmH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 110βΒ΅F
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- The Atlas IV as on the factory drawing.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.