Transistor preamp into one EL84, 1972 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Marshall Mercury 2060.
Two BC184 transistor stages with a Volume and a Tone between them, into one EL84 single-ended. A third BC184 runs the tremolo, which swings the EL84’s grid.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each transistor stage has a 220 kΩ collector load and 6.8 MΩ from collector to base, which sets its bias and feeds a little of the output back. The first stage’s 22 nF emitter cap lifts its treble. The Tone pot fades between a treble path through 220 pF and a bass path through 100 kΩ with 22 nF to ground. The EL84 is the only tube and the only stage that clips softly. The tremolo adds a slow swing to the EL84’s grid through the Intensity pot, so it moves the tube’s bias up and down. At 0 the swing is off. The oscillator runs all the time, and its current swings rail A by about 0.8 V, so a faint tick at its speed reaches the speaker even with Intensity at 0.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R1, 220 kΩ
- In series with the High input, 220 kΩ. With R2 and the stage’s input it cuts the level.
- C1, 2.2 nF
- Across R1, 2.2 nF. It lets the treble around R1, so High is thinner and brighter than Low.
- R2, 100 kΩ
- From R1 to the Low jack, 100 kΩ.
- C2, 2.2 nF
- From the Low jack to ground, 2.2 nF. With R2 it rolls off the treble on the High input.
- C3, 22 nF
- Input coupling cap into T1.
- T1, BC184C
- The first gain stage, a BC184.
- R3, 6.8 MΩ
- Collector to base, 6.8 MΩ. It biases the base from the collector, so the collector settles near 26 V, and it feeds a little signal back.
- R4, 6.8 MΩ
- Base to ground, 6.8 MΩ.
- C4, 100 pF
- Collector to base. Its value is marked “?” on the drawing, so 100 pF is assumed. It trims the stage’s far treble.
- R5, 220 kΩ
- T1’s collector load, 220 kΩ from rail A.
- R6, 10 kΩ
- T1’s emitter resistor, 10 kΩ. It sets the current and holds the low-end gain down.
- C5, 22 nF
- Across R6, 22 nF. It bypasses the emitter only above about 700 Hz, so the stage has more gain in the treble.
- C6, 22 nF
- Coupling cap to the Volume.
- Volume, 100 kΩ pot, audio taper
- Volume, 100 kΩ.
- C7, 220 pF
- Bright cap across the top of the Volume, 220 pF.
- C8, 220 pF
- The Tone pot’s treble path, 220 pF to its top.
- R7, 100 kΩ
- The Tone pot’s bass path, 100 kΩ to its bottom.
- C9, 22 nF
- From the Tone pot’s bottom to ground, 22 nF. With R7 it keeps only the bass on that end.
- Tone, 100 kΩ pot, linear taper
- Tone, 100 kΩ. Clockwise, the wiper moves to the treble end.
- C10, 22 nF
- Coupling cap into T2.
- T2, BC184C
- The second gain stage, a BC184.
- R8, 6.8 MΩ
- Collector to base, 6.8 MΩ, as R3.
- R9, 6.8 MΩ
- Base to ground, 6.8 MΩ.
- C11, 100 pF
- Collector to base, marked “?” on the drawing. 100 pF is assumed.
- R10, 220 kΩ
- T2’s collector load, 220 kΩ.
- R11, 10 kΩ
- T2’s emitter resistor, 10 kΩ.
- C12, 22 µF electrolytic
- T2’s emitter bypass, 22 µF. The stage has full gain from the bass up.
- C13, 47 nF
- Coupling cap to the EL84’s grid leak.
- Intensity, 100 kΩ pot, audio taper
- Intensity, 100 kΩ. It is also the EL84’s grid leak. The tremolo comes in at the wiper, so turned up, more of the slow swing reaches the grid.
- R12, 2.7 kΩ
- Grid stopper into the EL84, 2.7 kΩ.
- T3, BC184C
- The tremolo’s oscillator, a BC184. The three caps from its collector turn the signal round at one frequency, and it runs there, a few times a second.
- R18, 220 kΩ
- The oscillator’s collector load.
- R21, 6.8 MΩ
- Collector to base, 6.8 MΩ, the oscillator’s bias.
- C23, 220 pF
- Collector to base, 220 pF. It keeps the oscillator off radio frequencies.
- C20, 47 nF
- First ladder cap.
- R19, 270 kΩ
- In series with Speed. It sets the slowest speed.
- Speed, 100 kΩ pot, linear taper
- Speed, 100 kΩ as a variable resistor to ground. Less resistance runs the oscillator faster.
- C21, 47 nF
- Second ladder cap.
- R20, 220 kΩ
- Second ladder resistor.
- C22, 47 nF
- Third ladder cap, into the base.
- R22, 220 kΩ
- Base to ground, the ladder’s last resistor.
- C24, 10 µF electrolytic
- Coupling cap out of the oscillator.
- R23, 47 kΩ
- To the footswitch line.
- R24, 47 kΩ
- From the footswitch line to the Intensity wiper.
- V1, EL84 / 6BQ5
- EL84, the output tube, single-ended: it carries the whole signal, and its idle current runs through the transformer all the time. Its cathode resistor biases it. Its grid connects straight to the preamp’s volume pot, which is its path to ground.
- 1k, 1 kΩ
- Screen resistor for tube A. It limits the screen current when the tube is driven hard.
- 100, 100 Ω
- The cathode resistor. The tube’s current runs through it and lifts the cathode above the grid, and that’s the bias. Driven hard, the tube draws more current on average, so the cathode climbs and the bias goes colder.
- 100µ, 100 µF electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 1k, 1 kΩ
- Dropping resistor from B+ to the screen supply. The screens sit slightly below the plates.
- 32µ, 32 µF electrolytic
- Filter cap on the screen supply.
- 27k, 27 kΩ
- Dropping resistor from the screen supply node to the node for the preamp, as on the Marshall Mercury 2060 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 10µ, 10 µF electrolytic
- Filter cap at the node for the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 5 kΩ to 4 Ω, 14.3 H primary, 54.3 mH leakage
- The output transformer, 5 kΩ from the plate to B+ into 4 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 210 V ac, 60 Hz
- The transformer’s high-voltage winding, 210 V ac with one end grounded, as a sine source at the mains frequency. Turn it up and every voltage in the amp goes up, the same as with a higher wall voltage.
- PT R, 30 Ω
- The winding’s resistance, estimated. It and the rectifier limit the charging current into the reservoir cap.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- 32µ, 32 µF electrolytic
- The reservoir cap. It feeds the output transformer’s B+ end. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 4.34 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 4 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 128 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 232 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 7.15 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 1.06 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 1.09 Ω
- Limits what Loss L2 adds.
- Tank R, 41.9 Ω
- Height of the bass resonance, about 46 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 10.6 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 440 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- BC184
- Three BC184s, modeled as the BC184C. The drawing shows no grade.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.