Six-stage photocell phaser, 1975 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Musitronics Mu-Tron Bi-Phase.
Six all-pass stages, which pass every pitch at the same level and only turn its phase, are each set by a photocell, and one LED lights all six. A sweep generator with a sine or square shape drives the LED, and Feedback sends part of the phased signal back to the input. One of the two phasers and one of the two sweep generators are built.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Z8B inverts the guitar and sends it through six all-pass stages. Each one keeps the level and turns the phase, 90Β° at 1 / (2Ο R C), where R is the stageβs cell in parallel with its 220 kΞ© and C is .0068 Β΅F. Six of them turn the phase 1,080Β°, so where the phased signal is inverted against the dry, the two cancel. That is three notches, with peaks between them. With the LED dark the cells sit near 220 kΞ© and the stages turn at about 106 Hz. With the LED at 10 mA the cells drop to about 1 kΞ©, and the stages turn at about 23 kHz. Sweep Generator 1 is a triangle generator, 0.42 to 22 sweeps a second on Rate. Shape selects the generatorβs triangle (Sine on the panel) or a rounded square. Depth sets how much of it reaches the LED driver, and the Offset trim sets where the LED rests. The driver turns the sweep into LED current, rising faster near the top. Feedback sends up to 0.86 of the phaserβs output back into Z8B, so the peaks between the notches ring. The footswitch lights PM1, a second LED and cell, which lets the phased signal into the mixer. With PM1 dark only the dry signal comes through. The cellsβ figures are typical of a VTL5C-type cell and assumed. The second phaser and Sweep Generator 2, the pedal input, Sweep Sync, the B output and the mains supply are left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- β15 V, -15 V
- The β15 V rail. The unitβs regulators make it from the mains, modeled as a steady source.
- C1, 47βnF
- Input coupling cap. With R1 it cuts below about 9 Hz.
- R1, 390βkΞ©
- Holds the input at ground. It is most of the input impedance.
- R2, 3.9βkΞ©
- With C2, keeps radio frequencies out of Z8A.
- C2, 30βpF
- With R2, a low-pass far above the audio band.
- Z8A, RC4558
- Half a 4558, a follower. Its output is the dry signal.
- R3, 390βkΞ©
- Feedback from Z8Aβs output to its minus input. With nothing from the minus input to ground, the gain stays 1.
- C3, 100βnF
- Across R3.
- R4, 4.7βkΞ©
- Into Z8Bβs minus input from the dry signal.
- R5, 4.7βkΞ©
- Z8Bβs feedback, equal to R4, so the dry signal goes into the phaser inverted at the same level.
- C4, 1βnF
- Across R5. It rolls Z8B off above about 34 kHz.
- Z8B, RC4558
- Half a 4558. It inverts the dry signal and adds the feedback from its plus input, at a gain of 2.
- R6, 4.7βkΞ©
- With R7, a divider on the feedback. Z8Bβs gain of 2 makes up for it, so at full Feedback 0.86 of the phaserβs output comes back.
- C5, 3.3βnF
- Across R6. It trims the feedback above about 18 kHz.
- R7, 6.2βkΞ©
- From the Feedback wiper to Z8Bβs plus input.
- Feedback, 10βkΞ© pot, audio taper
- Feedback, 10 kΞ©, across the phaserβs output. Its wiper sends part of the phased signal back into Z8B. Turned up, the peaks between the notches ring, up to about 11 dB at full, and the notches get shallower. The taper is assumed.
- R8, 4.7βkΞ©
- Into the minus input. Equal to the feedback resistor, so every pitch comes out at the same level and only the phase moves.
- R9, 4.7βkΞ©
- Feedback, equal to the input resistor.
- C6, 6.8βnF
- From the stageβs input to the plus input. With the cell and its 220 kΞ© it sets the pitch where this stage turns the phase 90Β°, which is 1 / (2Ο R C). Lows come out inverted, highs come out as they went in.
- R10, 220βkΞ©
- Across the cell. It sets the most resistance the stage can have, so with the LED dark this stage turns at about 106 Hz.
- PM3A, VTL5C-type cell
- One of the six photocells around PM3βs LED. Lit harder, its resistance falls and the stage turns at a higher pitch. Its figures are typical of a VTL5C-type cell and assumed.
- Z1A, RC4558
- Half a 4558, the first of six all-pass stages.
- R11, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R12, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C7, 6.8βnF
- This stageβs .0068 Β΅F. All six are the same, so the stages turn together.
- R13, 220βkΞ©
- Across the cell, 220 kΞ©.
- PM3B, VTL5C-type cell
- Another of PM3βs six cells.
- Z1B, RC4558
- Half a 4558, all-pass stage 2.
- R14, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R15, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C8, 6.8βnF
- This stageβs .0068 Β΅F. All six are the same, so the stages turn together.
- R16, 220βkΞ©
- Across the cell, 220 kΞ©.
- PM3C, VTL5C-type cell
- Another of PM3βs six cells.
- Z2A, RC4558
- Half a 4558, all-pass stage 3.
- R17, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R18, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C9, 6.8βnF
- This stageβs .0068 Β΅F. All six are the same, so the stages turn together.
- R19, 220βkΞ©
- Across the cell, 220 kΞ©.
- PM3D, VTL5C-type cell
- Another of PM3βs six cells.
- Z2B, RC4558
- Half a 4558, all-pass stage 4.
- R20, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R21, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C10, 6.8βnF
- This stageβs .0068 Β΅F. All six are the same, so the stages turn together.
- R22, 220βkΞ©
- Across the cell, 220 kΞ©.
- PM3E, VTL5C-type cell
- Another of PM3βs six cells.
- Z3A, RC4558
- Half a 4558, all-pass stage 5.
- R23, 4.7βkΞ©
- Into the minus input, as in the first stage.
- R24, 4.7βkΞ©
- Feedback, 4.7 kΞ©.
- C11, 6.8βnF
- This stageβs .0068 Β΅F. All six are the same, so the stages turn together.
- R25, 220βkΞ©
- Across the cell, 220 kΞ©.
- PM3F, VTL5C-type cell
- Another of PM3βs six cells.
- Z3B, RC4558
- Half a 4558, all-pass stage 6.
- C12, 470βnF
- Couples the phaserβs output to the Feedback pot and Z9B.
- R109, 47βkΞ©
- The sweep from Depthβs wiper into the LED driver.
- R112, 47βkΞ©
- The Offset trimβs voltage into the LED driver.
- R113, 3.6βkΞ©
- With R109 and R112 it makes a divider, so the driver sees about a fifteenth of the sweep with the offset added.
- Offset, 10βkΞ© pot, linear taper
- The Sweep A Offset trim, 10 kΞ© from +15 V to ground. It sets where the LED rests with Depth at 0. It is set at a quarter (assumed). There the LED rests near 1.6 mA and the notches near 1.8, 6.1 and 18 kHz, and a full sweep runs the LED from dark to about 10 mA.
- Z27B, RC4558
- Half a 4558, the LED driver. It drives Q2 until the voltage under the LED, fed back through R114, matches its plus input.
- Q2, 2N3904
- Emitter follower that carries the LEDβs current from +15 V. Its marking is unreadable on the drawing, so it is a 2N3904 as on the other channel.
- PM3, Red LED
- The LED in the six-cell module. Its light follows its current, which runs from near 0 to about 10 mA over a full sweep.
- CR17, 1N914 / 1N4148
- Across the LED backward, so it never sees more than a diode drop in reverse.
- R114, 220βkΞ©
- Feedback from under the LED to Z27Bβs minus input. With R116 it sets the driverβs gain at about 4.2.
- R116, 68βkΞ©
- From Z27Bβs minus input to ground.
- R115, 10βkΞ©
- With CR10, a second leg from the minus input to ground. Once the minus input is over about half a volt it draws current, and the driverβs gain rises to about 26, so the LEDβs current climbs faster at the top of the sweep.
- CR10, 1N914 / 1N4148
- The knee in the driverβs curve.
- Range, 1βkΞ© pot, linear taper
- The Sweep A Range trim, 1 kΞ© used as a variable resistor under the LED. More resistance means less current for the same drive, so a narrower sweep. Set at half (assumed).
- R117, 220βΞ©
- The least resistance under the LED, so Range at 0 canβt short it to ground.
- Rate, 25βkΞ© pot, linear taper
- Rate A, 25 kΞ© linear from +15 V to ground. Its wiper sets the control voltage, and that sets the sweep rate. It is 0.42 sweeps a second at 0, 1.5 at 0.05, 9.9 at half and 22 at full.
- R65, 47βkΞ©
- From Rateβs wiper into Z12A, through the Rate Control switch at Manual.
- R68, 20βkΞ©
- From +15 V to the top of the low speed trim.
- Low speed, 10βkΞ© pot, linear taper
- The LFO Low Speed trim, 10 kΞ©. It sets the slowest sweep, with Rate at 0. Set at half (assumed).
- R67, 390βkΞ©
- From the low speed trim into Z12A.
- Z12A, RC4558
- Half a 4558, an inverting stage. Its output is the control voltage, negative, about 0.8 times Rateβs wiper.
- R66, 39βkΞ©
- Z12Aβs feedback resistor.
- CR1, 1N914 / 1N4148
- In Z12Aβs feedback, so its output only goes negative. Its drop matches the bridge diodesβ.
- R70, 39.2βkΞ©
- Into Z12B, 1 %.
- R71, 39.2βkΞ©
- Z12Bβs feedback, 1 %, equal to R70, so its output is the control voltage turned positive.
- Z12B, RC4558
- Half a 4558, an inverter. With it the bridge is fed the control voltage in both polarities.
- R69, 33βkΞ©
- Pulls current out of the bridge, set by the negative control voltage.
- R72, 33βkΞ©
- Pushes the same current into the bridge from the positive control voltage. Faded on the drawing, read as R69.
- CR2, 1N914 / 1N4148
- Bridge diode. With the square low it carries R69βs current out of the integrator, so the triangle ramps up.
- CR3, 1N914 / 1N4148
- Bridge diode. With the square high it feeds R69βs current from the comparator.
- CR4, 1N914 / 1N4148
- Bridge diode. With the square low it sends R72βs current into the comparator.
- CR5, 1N914 / 1N4148
- Bridge diode. With the square high it carries R72βs current into the integrator, so the triangle ramps down.
- C33, 470βnF
- The integratorβs cap. The bridgeβs current charges it at a steady rate, so the output ramps in straight lines.
- Z13B, RC4558
- Half a 4558, the integrator. Its output is the triangle, about Β±9 V. CR6 feeds this 4558βs positive supply pin, so its rail sits 0.6 V under +15 V.
- Z13A, RC4558
- The other half, a comparator. Its output flips to the other rail each time the triangle reaches a peak, and steers the bridge.
- R73, 68βkΞ©
- Positive feedback that holds the comparator where it last flipped. Against R74 it sets the triangleβs height, 47 / 68 of the square.
- R74, 47βkΞ©
- From the triangle into the comparator.
- R75, 47βkΞ©
- From the triangle to the Sine contact. Its value is unreadable on the drawing. 47 kΞ© is assumed, which puts the triangle at Z15A close to the rounded squareβs swing.
- R76, 120βkΞ©
- From the square to the Square contact. With C36 it rounds the squareβs edges.
- C36, 470βnF
- Rounds the square, so the LED moves between its two places in about 20 ms.
- R77, 47βkΞ©
- With the Gen 1 Amp trim, the load on the shape switch. It sets how much of the shape reaches Z15A.
- Gen 1 Amp, 25βkΞ© pot, linear taper
- The Gen 1 Amp trim, 25 kΞ© used as a variable resistor under R77. More resistance means a bigger sweep. Set at its full 25 kΞ© (assumed).
- Z15A, RC4558
- Half a 4558, a follower that drives Depth.
- Depth, 10βkΞ© pot, linear taper
- Depth A, 10 kΞ© linear. Its wiper sends part of the sweep to the LED driver, so it sets how far the notches move. At 0 they hold where the Offset trim sets them.
- R96, 560βΞ©
- Under Depth.
- R26, 4.7βkΞ©
- Into Z9B from the phaserβs output.
- R27, 4.7βkΞ©
- Z9Bβs feedback, equal to R26.
- C13, 1βnF
- Across R27. It rolls Z9B off above about 34 kHz.
- Z9B, RC4558
- Half a 4558. It inverts the phased signal again, so it meets the dry the right way round.
- PM1, VTL5C-type cell
- The bypass cell. Lit by the footswitch, it drops to about 1.7 kΞ© and lets the phased signal into the mixer. Dark, it is megohms and only the dry gets through. Its figures are typical of a VTL5C-type cell and assumed.
- Notch Depth, 10βkΞ© pot, linear taper
- The Notch Depth A trim, 10 kΞ© used as a variable resistor. It sets the phased signalβs level at the mixer. It is set so the wet side matches R51βs 12 kΞ© with PM1 lit, which makes the deepest notches (assumed).
- C14, 150βnF
- Blocks DC on the wet side.
- R29, 4.7βkΞ©
- The wet side into the mixer.
- R51, 12βkΞ©
- The dry side into the mixer.
- C15, 470βpF
- A low-pass at the mixer, above about 50 kHz.
- Z9A, RC4558
- Half a 4558, a follower that drives the output.
- R32, 560βΞ©
- Keeps a long cableβs capacitance off Z9A.
- C16, 10βΒ΅F electrolytic
- Output coupling cap.
- R30, 2.7βkΞ©
- Feeds PM1βs LED from the pedal line, about 4.9 mA with the line grounded.
- PM1 LED, Red LED
- PM1βs LED, from the pedal line to β15 V.
- R28, 1.2βkΞ©
- Feeds the panel LED, about 11 mA.
- CR18, Red LED
- The panelβs Phase A LED, lit while the effect is on.
About this version
- Stock
- The original runs from the mains on Β±15 V. In the model these are the battery part at 15 V and a β15 V source. RC4558 op-amps, red LEDs lighting VTL5C-type cells.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.