OTA state-variable envelope filter, early 1980s style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the DOD 545 Wah/Filter.
An auto-wah on two CA3094 OTAs. The guitar’s level, rectified, sets both OTAs’ bias current, and that tunes a two-integrator filter. Sensitivity sets how hard you have to play, Attack how fast the peak follows, Peak how tall it is.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each CA3094 is an OTA, an amplifier whose output current is set by a bias current, with a follower inside. Each OTA charges a 10 nF cap, so it integrates, and the two in a loop make a filter. Its peak moves up as the bias current rises. With the knobs at their default settings the response is flat up to a peak near 470 Hz, about 8 dB tall, and falls above it. U1B amplifies the guitar up to about 100 times, set by Sensitivity. C8 and R20 cut its input below about 1 kHz, so it follows mostly the pick’s attack. C9, D1 and D2 rectify its output into node P, which rests at about 1.6 V. Through Attack, C10 smooths it, and Q1 drives the OTAs’ bias pins through R14 and R15. With 1.5 V on Q1’s emitter the peak is near 1 kHz, with 4 V near 3.6 kHz. A 200 mV pick at A2 with Sensitivity at full moves the peak to about 1.5 kHz. The drawing has no part numbers, and its pot tapers and directions are assumed. The bypass switching, the LED and the supply’s slow-start circuit are left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- RB1, 22 kΩ
- Top of the Vbias divider.
- RB2, 22 kΩ
- Bottom of the Vbias divider. With RB1 it sets Vbias at 9 V.
- CB, 10 µF electrolytic
- Filters Vbias.
- C1, 10 nF
- Input coupling cap.
- R1, 10 kΩ
- In series with the buffer’s input.
- R2, 470 kΩ
- Holds the buffer’s input at Vbias. Most of the pedal’s input impedance.
- U1A, TL062 (low power)
- Half of the TL062, a follower that buffers the guitar.
- R3, 10 kΩ
- From the buffer into OTA 1’s plus input. With R4 it divides the guitar down about 11 times, since an OTA’s input handles only tens of millivolts cleanly.
- R4, 1 kΩ
- From OTA 1’s plus input to N0.
- R5, 1 kΩ
- From OTA 1’s minus input to N0.
- U2, CA3094
- The first CA3094’s OTA. Its output current, set by the bias current from the envelope, charges C2, so it integrates.
- C2, 10 nF
- The first integrator’s cap.
- QA1, 2N3904
- The first CA3094’s Darlington follower, first half. It buffers C2.
- QA2, 2N3904
- The Darlington’s second half. Its emitter is the band-pass output.
- R7, 22 kΩ
- The first follower’s emitter load.
- R8, 22 kΩ
- Feeds part of the band-pass output back into OTA 1’s minus input, through Peak.
- Peak, 100 kΩ pot, linear taper
- Peak, 100 kΩ, a variable resistor in series with R8. More resistance feeds back less of the band-pass output, so the peak is taller and narrower. Taper and direction assumed.
- R9, 22 kΩ
- Feeds the low-pass output back into OTA 1’s minus input. This closes the filter’s loop.
- R10, 22 kΩ
- From the band-pass output into OTA 2’s plus input. With R11 it divides it down about 23 times.
- R11, 1 kΩ
- From OTA 2’s plus input to N0.
- R12, 1 kΩ
- From OTA 2’s minus input to N0.
- U3, CA3094
- The second CA3094’s OTA, the second integrator.
- C3, 10 nF
- The second integrator’s cap.
- QB1, 2N3904
- The second CA3094’s Darlington follower, first half.
- QB2, 2N3904
- The Darlington’s second half. Its emitter is the low-pass output.
- R13, 22 kΩ
- The second follower’s emitter load.
- R6, 5 kΩ
- From the band-pass output toward the output jack.
- C5, 1 µF electrolytic
- Output coupling cap.
- R16, 1 kΩ
- In series with the output.
- C6, 100 nF
- Second output cap.
- R17, 100 kΩ
- Holds the output at 0 V DC.
- C8, 1 nF
- Couples the buffer into the envelope amp. With R20 it cuts below about 1 kHz, so the envelope follows the pick’s attack more than the note’s body.
- R20, 150 kΩ
- Holds the envelope amp’s plus input at Vbias.
- U1B, TL062 (low power)
- The other TL062 half, the envelope amp. Its gain is 1 plus 1 MΩ over R18 and Sensitivity.
- R19, 1 MΩ
- The envelope amp’s feedback resistor.
- R18, 10 kΩ
- Sets the envelope amp’s highest gain, about 100.
- C7, 100 nF
- Blocks DC from the gain leg.
- Sensitivity, 500 kΩ pot, linear taper
- Sensitivity, 500 kΩ, a variable resistor in the envelope amp’s gain leg. Clockwise there is less resistance and more gain. The drawing marks its taper D. Linear and the direction are assumed.
- C9, 4.7 µF electrolytic
- Couples the envelope amp to the rectifier.
- D1, 1N914 / 1N4148
- Clamps C9’s far side near ground on the down swings.
- D2, 1N914 / 1N4148
- Passes the up swings into node P.
- R21, 22 kΩ
- From node P to ground. With R22 it holds P at about 1.6 V between picks.
- R22, 220 kΩ
- From 18 V to node P. It sets the resting bias current, so where the peak rests.
- Attack, 100 kΩ pot, linear taper
- Attack, 100 kΩ, a variable resistor from node P to C10. With C10 it sets how fast the peak follows a pick. Clockwise, less resistance and a faster attack. Taper and direction assumed.
- C10, 4.7 µF electrolytic
- Smooths the envelope at Q1’s base.
- Q1, 2N4124
- 2N4124, a follower that feeds both OTAs’ bias pins.
- R14, 10 kΩ
- Sets OTA 1’s bias current from the envelope.
- R15, 10 kΩ
- Sets OTA 2’s bias current from the envelope.
- C4, 1 nF
- On OTA 2’s bias pin.
About this version
- Stock
- Negative ground, 18 V. Two CA3094s and a TL062. Each CA3094’s Darlington is drawn as two transistors.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.