Germanium and silicon pair fuzz with germanium diodes, 1975 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Interfax Harmonic Percolator.
A germanium PNP and a silicon NPN share one current path, with their emitters joined and bypassed. The silicon stage’s output goes through two lopsided germanium diode legs to ground.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q2’s emitter current has nowhere to go but through Q1 and R2, so the two transistors run on the same current, set by R2. Q1 amplifies the guitar into its collector, and C4 carries that to Q2’s base. Q2 then amplifies it again into R4. The diodes are not the same on each side. One side is a bare germanium diode, the other has 4.7 kΩ in series, so one half of the wave clips harder than the other and the fuzz has a strong even harmonic. Harmonics is a volume control in front of the fuzz. Balance is the output level, and it also loads the diodes.
Download.
Parts and what they do
Stock values for the Stock values version. Tap a part on the schematic to change it.
- Harmonics, 100 kΩ pot, audio taper
- Harmonics, 100 kΩ audio, a volume control in front of the fuzz. Turned down it works much like the guitar’s own volume.
- C1, 100 pF
- Trims radio pickup and the highest treble at the wiper.
- C2, 47 nF
- Input coupling cap into Q1.
- Q1, 2N404A
- A 2N404A germanium PNP, the first stage. Its emitter sits on the joined emitters and its collector feeds R2.
- R1, 220 kΩ
- Biases Q1’s base from its own collector.
- R2, 20 kΩ
- Q1’s collector load, and the only DC path to ground for both transistors, so it sets the current through both.
- C3, 47 µF electrolytic
- Bypasses the joined emitters to ground, so each stage runs at full gain.
- C4, 1 µF electrolytic
- Carries Q1’s output to Q2’s base.
- C5, 1 nF
- Trims the treble at Q1’s collector, from about 8 kHz up with R2.
- Q2, 2N3904
- The second stage, a silicon NPN (2N3565 in the original). Its emitter current runs through Q1.
- R3, 750 kΩ
- Biases Q2’s base from its own collector.
- R4, 91 kΩ
- Q2’s collector load.
- C6, 100 nF
- Output coupling cap into the diodes and Balance.
- D3, 1N60 germanium
- A germanium diode (1N695) from ground. It clips the negative half of the wave at about 0.3 V.
- R5, 4.7 kΩ
- In series with D2, so the positive half clips more softly.
- D2, 1N60 germanium
- The other germanium diode (1N695), to ground through R5.
- Balance, 50 kΩ pot, audio taper
- Balance, 50 kΩ audio, the output level.
Versions
- Stock values
- Negative ground, 9 V. The values traced from most units: R1 220 kΩ, R2 20 kΩ, R3 750 kΩ, C4 1 µF, C5 1 nF.
- Five values changed
- One traced unit with five values changed: R1 51 kΩ, R2 91 kΩ, R3 3.9 MΩ, C4 2.2 µF, C5 1.5 nF. The larger R2 runs both transistors on about a fifth the current.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.