Four-stage MOSFET phaser, 1982 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Korg PHS-1 Phaser.
Four op-amp stages, each set by a MOSFET with a resistive gate, turn the guitar’s phase. The wet signal meets the buffered dry signal in an op-amp mixer, and the two cancel at two notches. A slow oscillator moves the gates. Knobs Speed and Intensity.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC5A buffers the guitar, and its output feeds four all-pass stages and the dry side of the mixer. Each stage passes every pitch at the same level and turns its phase, 90° at 1 / (2π R C), where R is the stage’s MOSFET beside its 110 kΩ and C is 10 nF. Where the wet signal has turned 180° and 540° it cancels the dry, so four stages make two notches. R11 feeds the fourth stage back into the second, so the peak between the notches stands about 4.8 dB high. The MOSFETs’ gates sit on one control line, about 1.1 V below the 5.1 V line. With Intensity at 7 the LFO swings that line about 0.17 V, and the lower notch sweeps from about 270 Hz to 950 Hz, the upper from about 1.3 to 4.5 kHz. Speed runs from one sweep every 7.8 seconds to about 9.7 a second. C13 smooths the control line, so the faster the sweep, the narrower it gets. The MOSFETs are a CD4007 P channel standing in for the TX-429D, with the bias trimmer set to suit, so a real pedal’s sweep may sit elsewhere.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C1, 100 µF electrolytic
- The 9 V supply’s filter cap.
- R1, 6.8 kΩ
- From the 9 V supply to the zener. About 0.57 mA flows through it.
- D3, 5.1 V zener, in breakdown
- A 5.1 V zener (RD5.1EB2). It holds the reference line that every op-amp stage and every MOSFET source sits on.
- C2, 100 µF electrolytic
- The reference line’s filter cap. It makes the line a quiet AC ground for the stages.
- C11, 10 nF
- Input coupling cap. Against R10 it cuts below about 16 Hz.
- R16, 10 kΩ
- In series with the buffer’s plus input.
- R10, 1 MΩ
- Biases the buffer at the 5.1 V line. The guitar sees about 1 MΩ.
- IC5A, JRC4558D
- Half an NJM4558, the input buffer, a gain of one. Its output feeds the phase-shift stages and the dry side of the mixer.
- R13, 10 kΩ
- Into the minus input. With the 10 kΩ feedback resistor it makes the inverting half of the stage, a gain of one.
- R17, 10 kΩ
- Feedback, equal to the input resistor, so every pitch comes out at the same level and only the phase moves.
- C7, 10 nF
- Feeds the plus input. With the 110 kΩ and the MOSFET beside it, it sets where this stage turns the phase 90°, about 145 Hz with the MOSFET off.
- R6, 110 kΩ
- From the plus input to the reference line, beside the MOSFET. It sets the lowest the stage’s 90° point can go.
- IC1, CD4007UB P channel
- A P-channel MOSFET used as a resistor that the LFO varies. The drawing marks a TX-429D, “selected”. A CD4007 P channel stands in. The further its gate sits below the 5.1 V line, the lower its resistance and the higher this stage’s 90° point.
- C3, 4.7 nF
- Couples the signal on the MOSFET’s channel onto one end of its gate (pin 6). With the gate’s other end held by the control line, the gate follows half the signal, and the channel’s resistance stays even as the signal swings.
- R2, 1 MΩ
- Holds pin 6 at the control line’s DC voltage, beside the gate strip.
- Gate 1a, 500 kΩ
- Half of the MOSFET’s resistive gate, from pin 6 to its middle. The part’s real gate resistance isn’t known. 500 kΩ is assumed.
- Gate 1b, 500 kΩ
- The other half of the gate strip, from its middle to pin 4 on the control line. Assumed 500 kΩ.
- IC5B, JRC4558D
- Half an NJM4558, the first of four phase-shift stages.
- R18, 10 kΩ
- Into the minus input, as in the first stage.
- R19, 10 kΩ
- Feedback, equal to the input resistor.
- C8, 10 nF
- Feeds the plus input, 10 nF as in every stage.
- R7, 110 kΩ
- Beside this stage’s MOSFET, 110 kΩ.
- IC2, CD4007UB P channel
- This stage’s MOSFET, on the same control line.
- C4, 4.7 nF
- Couples the channel’s signal onto pin 6, as in the first stage.
- R3, 1 MΩ
- Holds pin 6 at the control line’s DC voltage.
- Gate 2a, 500 kΩ
- Half the gate strip, pin 6 side, assumed 500 kΩ.
- Gate 2b, 500 kΩ
- Half the gate strip, pin 4 side, assumed 500 kΩ.
- IC6A, JRC4558D
- Half an NJM4558, phase-shift stage 2.
- R14, 10 kΩ
- Into the minus input, as in the first stage.
- R20, 10 kΩ
- Feedback, equal to the input resistor.
- C9, 10 nF
- Feeds the plus input, 10 nF as in every stage.
- R8, 110 kΩ
- Beside this stage’s MOSFET, 110 kΩ.
- IC3, CD4007UB P channel
- This stage’s MOSFET, on the same control line.
- C5, 4.7 nF
- Couples the channel’s signal onto pin 6, as in the first stage.
- R4, 1 MΩ
- Holds pin 6 at the control line’s DC voltage.
- Gate 3a, 500 kΩ
- Half the gate strip, pin 6 side, assumed 500 kΩ.
- Gate 3b, 500 kΩ
- Half the gate strip, pin 4 side, assumed 500 kΩ.
- IC6B, JRC4558D
- Half an NJM4558, phase-shift stage 3.
- R21, 10 kΩ
- Into the minus input, as in the first stage.
- R22, 10 kΩ
- Feedback, equal to the input resistor.
- C10, 10 nF
- Feeds the plus input, 10 nF as in every stage.
- R9, 110 kΩ
- Beside this stage’s MOSFET, 110 kΩ.
- IC4, CD4007UB P channel
- This stage’s MOSFET, on the same control line.
- C6, 4.7 nF
- Couples the channel’s signal onto pin 6, as in the first stage.
- R5, 1 MΩ
- Holds pin 6 at the control line’s DC voltage.
- Gate 4a, 500 kΩ
- Half the gate strip, pin 6 side, assumed 500 kΩ.
- Gate 4b, 500 kΩ
- Half the gate strip, pin 4 side, assumed 500 kΩ.
- IC7A, JRC4558D
- Half an NJM4558, the fourth stage. Its output is the wet signal.
- R11, 33 kΩ
- Feeds the fourth stage’s output back into the second stage’s minus input. The notches go deeper and the pitches between them stand out more.
- R24, 15 kΩ
- The dry signal into the mixer.
- R15, 15 kΩ
- The wet signal into the mixer, equal to R24, so the notches go deep.
- R23, 10 kΩ
- The mixer’s feedback. Each input reaches the output at 10 k / 15 k, about two thirds.
- R12, 10 kΩ
- Holds the mixer’s plus input at the 5.1 V line.
- IC7B, JRC4558D
- Half an NJM4558, the mixer. It adds the dry and wet signals and inverts the sum.
- C12, 10 µF electrolytic
- Output coupling cap.
- R26, 10 kΩ
- Holds C12’s far end at ground.
- R27, 470 Ω
- In series with the output.
- R36, 47 kΩ
- Top of the bias divider, from the 5.1 V line.
- VR2, 100 kΩ pot, linear taper
- The internal bias trimmer, 100 kΩ. It sets how far below the 5.1 V line the gates sit. Set at 0.85 for this file’s MOSFET, an assumed setting.
- R37, 47 kΩ
- Bottom of the bias divider.
- R34, 1 MΩ
- The bias into the control line.
- C13, 100 nF
- Holds the control line steady at audio, so the four gates don’t pass signal between the stages.
- IC8A, TL062 (low power)
- Half a TL062, the LFO’s switching half. Its output jumps between high and low.
- R32, 470 kΩ
- Positive feedback from the output. With R31 it sets the two switch points either side of 5.1 V.
- R31, 150 kΩ
- From the plus input to the 5.1 V line.
- C14, 10 nF
- From the output to the minus input. With R30 it slows the output’s jumps slightly.
- R30, 150 kΩ
- From the timing cap to the minus input.
- R29, 4.7 kΩ
- In series with Speed. It sets the top speed.
- Speed, 500 kΩ pot, reverse audio taper
- Speed, 500 kΩ C taper, a variable resistor from R29 to the timing cap. At full it’s out of the path, the fastest setting.
- C16, 15 µF electrolytic
- The timing cap, a tantalum. It ramps up and down between the switch points, and that ramp is the sweep.
- IC8B, TL062 (low power)
- Half a TL062, a follower on the timing cap, so the sweep’s load doesn’t slow the ramp.
- R35, 68 kΩ
- From the follower to the top of Intensity.
- Intensity, 100 kΩ pot, linear taper
- Intensity, 100 kΩ B. It sets how much of the ramp reaches the gates. At 0 the wiper sits on the 5.1 V line and the notches stand still.
- VR1, 1 MΩ pot, linear taper
- The internal depth trimmer, 1 MΩ, a variable resistor in series with R28. Set at the middle, an assumed setting.
- R28, 1.5 MΩ
- The ramp into the control line. With R34 and VR1 about a third of the ramp reaches the gates.
About this version
- Stock
- The circuit as the factory drawing shows it. NJM4558 op-amps, a TL062 for the LFO, and a CD4007 P channel in place of each TX-429D.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.