Envelope filter on Norton amplifiers, 1975 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Colorsound Chuck-a-Wah (FET version).
An auto-wah on one MC3401 chip. The guitar’s level, rectified and smoothed, drives a JFET that tunes a band-pass filter. Intensity sets how far the peak moves for a given pick.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Stage 1 amplifies the guitar about 4.7 times and feeds two paths. One goes through R4 into the filter. Stage 4 is a band-pass filter with C7 and C8, 4.7 nF each. Its peak sits at about 190 Hz with Q1 off, 12 dB over the level away from the peak. Q1 and R14 connect the filter’s common node to the supply rail, which is an AC ground. As Q1 opens, their resistance falls and the peak rises, up to about 2.3 kHz. The other path goes through Intensity into stage 2, which rectifies it. Stage 3 smooths the result with C5 and drives Q1’s gate through R13. Intensity sets how much of the guitar reaches the rectifier. Most of the sweep happens over a narrow range of picking strength, so at some settings the peak jumps between its two ends more than it sweeps. The Range switch adds C9 and C10 beside the 4.7 nF caps, so the whole sweep moves down to about 64 to 740 Hz. The trimmer sets where the peak rests. Its value is not on the drawing.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- D1, 1N4001
- Series diode in the supply. It protects the chip if the battery goes in backward, and the rail sits about 0.7 V under the battery. Its type is not marked. A 1N4001 is assumed.
- C1, 47 nF
- Input coupling cap.
- R1, 100 kΩ
- Input resistor into stage 1. With R3 it sets the gain at about 4.7.
- R2, 1 MΩ
- Biases stage 1. Its current into the plus input sets the output’s resting voltage, about half R3 over R2 times the rail.
- U1A, MC3401
- One of the MC3401’s four Norton amplifiers, an inverting gain stage. A Norton amplifier works on the difference of the currents into its inputs.
- R3, 470 kΩ
- Stage 1’s feedback resistor.
- C2, 100 nF
- Couples stage 1 to the filter.
- R4, 220 kΩ
- The filter’s input resistor, into the common node.
- C3, 100 nF
- Couples stage 1 to Intensity.
- Intensity, 100 kΩ pot, linear taper
- Intensity, 100 kΩ. It sets how much of the guitar reaches the rectifier, so how far a pick moves the peak. The taper is not marked on the drawing. Linear is assumed.
- C4, 100 nF
- Couples Intensity’s wiper to the rectifier.
- R5, 47 kΩ
- From the rectifier input into stage 2’s minus input.
- R6, 16 kΩ
- From the rectifier input into stage 2’s plus input. Lower than R5, so the plus input wins and the stage doesn’t invert.
- U1D, MC3401
- The rectifier. It has no bias resistor, so it rests about 1 V above ground. A Norton input takes current only one way, so only one direction of the signal swings the output up.
- R7, 100 kΩ
- Stage 2’s feedback to the minus input.
- R8, 470 kΩ
- From stage 2’s output to its plus input.
- R9, 100 kΩ
- Carries the rectified signal into stage 3 as a current.
- U1C, MC3401
- The envelope stage. It smooths the rectified signal and adds the trimmer’s offset, then drives Q1’s gate.
- R10, 1 MΩ
- Stage 3’s feedback resistor.
- C5, 47 nF
- Across R10. With R10 it smooths the envelope over about 50 ms.
- R11, 220 kΩ
- From the rail to the top of the trimmer.
- Trim, 100 kΩ pot, linear taper
- The resting-point trimmer. Turned up, it feeds more current into stage 3’s minus input, which holds the envelope lower. Its value is not on the drawing. 100 kΩ is assumed. It is set at 0.245, where Q1 is just short of conducting, so the peak rests at the bottom and a medium pick starts the sweep.
- R12, 47 kΩ
- From the trimmer’s wiper into stage 3’s minus input.
- R13, 1 MΩ
- From the envelope to Q1’s gate.
- C6, 47 nF
- From the rail to Q1’s gate. With R13 it smooths the gate further.
- Q1, BF245A
- BF244A JFET, a variable resistor from the filter’s common node to the rail. As the gate rises it conducts more and the peak moves up. A BF245A model stands in.
- R14, 100 kΩ
- Beside Q1. It sets the bottom of the sweep, with Q1 off.
- U1B, MC3401
- The filter, a band-pass with feedback through both caps. Its peak is 1 / (2π C √(470 kΩ × R)), where C is 4.7 nF and R is R4 in parallel with R14 and Q1.
- R15, 1 MΩ
- Biases stage 4.
- C7, 4.7 nF
- One of the filter’s two tuning caps, to the minus input.
- C8, 4.7 nF
- The other tuning cap, to the output.
- R16, 470 kΩ
- The filter’s feedback resistor.
- C9, 10 nF
- Range cap. With Range at low it sits beside C7.
- R17, 10 MΩ
- Keeps C9 charged while the switch is open, so it doesn’t click.
- C10, 10 nF
- Range cap. With Range at low it sits beside C8.
- R18, 10 MΩ
- Keeps C10 charged while the switch is open.
- C11, 47 nF
- Output coupling cap.
- R19, 1 MΩ
- Holds the output at 0 V DC.
About this version
- As drawn
- Negative ground, 9 V through a series diode. One MC3401 quad Norton amplifier and a BF244A JFET.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.