Two-chip bucket-brigade delay with a compander, 1990 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Maxon AD-900 Analog Delay.
Two 4096-stage bucket brigades in a row delay the signal by about 19 to 580 ms. An SA571 compressor ahead of them and an expander after them keep the chips’ hiss down, and filters on both sides keep the clock out.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC1a lifts the treble by up to about 15.6 dB before the compressor, and IC1b cuts it the same amount at the output. The dry signal comes through flat, and the hiss added in between drops. The compressor halves the signal’s range in dB, the two chips delay it, and the expander doubles the range again. A three-pole filter ahead of the first chip cuts above about 2.5 kHz. Two more after the second chip lift slightly near 2 kHz and cut steeply above 3 kHz, so the clock stays out. D-Time sets the current TR7 pulls from the clock’s timing cap. TR6 and TR7 multiply that current by the same factor for each step of the knob’s voltage, so the delay is about 19 ms at 0, 165 ms at a quarter, 384 ms at half and 578 ms full up. Repeat sends a share of the delay back into the compressor, and D-Level sets how much delay is mixed with the dry signal. In bypass only the delay is cut, and the dry signal still goes through both op-amps. The model leaves out the clock feedthrough the Balance trims cancel, and IC4, the second clock chip. Both delay chips run at IC6’s rate.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C40, 100 µF electrolytic
- Filter cap on the 12 V adapter’s input.
- R54, 47 kΩ
- Top of the 6 V divider.
- R55, 47 kΩ
- Bottom of the 6 V divider. Both op-amps work around it.
- C41, 47 µF electrolytic
- Filters the 6 V line.
- C1, 47 nF
- Input coupling cap. With R2 the corner is about 7 Hz.
- R1, 1 kΩ
- In series with TR1’s base.
- R2, 510 kΩ
- Biases TR1 from the 6 V line and sets the input impedance near 510 kΩ.
- TR1, 2SC1815
- Emitter follower, the input buffer.
- R3, 10 kΩ
- TR1’s emitter load.
- C2, 1 µF
- Non-polar coupling cap into IC1a.
- R4, 10 kΩ
- IC1a’s input resistor. With R6 the gain is 1 for the lows.
- R5, 2 kΩ
- With C3, a second input path beside R4 that opens up in the treble, so the gain rises to about 6.
- C3, 33 nF
- Pre-emphasis cap. With R5 the treble lift starts near 2.4 kHz.
- IC1a, JRC4558D
- Pre-emphasis stage, inverting. Its gain is 1 for the lows and rises to about 6 (15.6 dB) in the treble, so the treble goes through the delay louder than the hiss.
- R7, 3.3 kΩ
- Holds IC1a’s + input on the 6 V line.
- R6, 10 kΩ
- IC1a’s feedback resistor.
- C4, 470 pF
- Across R6. It rolls the lift off above about 34 kHz.
- C5, 1 µF electrolytic
- Couples IC1a into the compressor.
- IC2 (1 to 8), NE571 (one half)
- SA571 half wired as a compressor. The input goes in at pin 6, and the gain cell and rectifier are fed from the output through C10. Every 2 dB change at the input is about 1 dB at the output, so quiet parts go into the delay louder. NE571 values.
- C6, 220 nF
- The compressor’s rectifier cap. With the chip’s 10 k it sets how fast the gain follows the level, about 2 ms.
- R9, 10 kΩ
- Half of the compressor’s DC feedback.
- R8, 10 kΩ
- Other half of the DC feedback.
- C8, 10 µF electrolytic
- Grounds the middle of R8 and R9 for audio, so they set only the DC.
- C10, 10 µF electrolytic
- Feeds the compressor’s output to its rectifier and gain cell.
- C9, 1 µF electrolytic
- Couples the repeats into the compressor’s summing node, beside the input.
- R10, 15 kΩ
- In series with the Repeat trim. With it, it sets how much the Repeat knob sends back.
- SR7 Repeat trim, 20 kΩ pot, linear taper
- Repeat trim, 20 kΩ as a variable resistor in series with R10. It sets how much the Repeat knob can send back. Set near its low end (0.15, assumed), where full Repeat slowly runs away, as most analog delays are set. At half, full Repeat dies away about 3 dB a repeat.
- R11, 10 kΩ
- First of three 10 kΩ resistors in the filter ahead of the first delay chip.
- Cx, 10 nF
- Filter cap to ground. Unnumbered on the board.
- R12, 10 kΩ
- Second filter resistor.
- C11, 56 nF
- Filter cap to TR2’s emitter. The emitter follows the filter’s output, so this cap sharpens the bend where the filter starts to cut.
- R13, 10 kΩ
- Third filter resistor.
- C12, 330 pF
- Filter cap to ground at TR2’s base.
- TR2, 2SC1815
- Emitter follower closing the first filter.
- R14, 10 kΩ
- TR2’s emitter load.
- C13, 10 µF
- Non-polar coupling cap into the first delay chip.
- R17, 5.1 kΩ
- Top of the Bias1 trim.
- SR2 Bias1, 10 kΩ pot, linear taper
- Bias trim for the first chip. At half (assumed) its input sits at 6.0 V, the middle of the chip’s swing, so the wave clips evenly top and bottom.
- R16, 5.1 kΩ
- Bottom of the Bias1 trim.
- C14, 1 µF electrolytic
- Keeps the signal off the Bias1 trim’s wiper.
- R15, 100 kΩ
- Carries the bias to the first chip’s input.
- IC3, MN3005
- First MN3005 bucket brigade, 4096 stages. Each clock cycle moves the samples one stage on, so it delays the signal by 2048 clock periods. Its two outputs are drawn as one pin. Swing set to 2.2 V for the 12 V supply, assumed. Clock feedthrough isn’t modeled.
- R18, 130 kΩ
- Load on output 1 (pin 3).
- R19, 130 kΩ
- Load on output 2 (pin 4).
- R20, 12 kΩ
- Feeds the output loads from the 12 V line.
- C16, 10 µF electrolytic
- Filters the output loads’ supply.
- SR3 Balance, 10 kΩ pot, linear taper
- Balance trim across the first chip’s two outputs, so the clock cancels. Both ends are on the one output pin here, so at half it’s 2.5 kΩ in series. The clock it cancels isn’t modeled.
- C17, 1 µF electrolytic
- Couples the first chip’s output to the Level trim.
- SR4 Level, 200 kΩ pot, linear taper
- Level trim between the chips, 200 kΩ to ground with its wiper into the second chip. It sets how loud the delay is. All the way up (assumed), the delay of a steady 440 Hz note comes back about 3 dB under the dry with D-Level full.
- C18, 1 µF electrolytic
- Couples the Level trim into the second chip.
- R23, 5.1 kΩ
- Top of the Bias2 trim.
- SR5 Bias2, 10 kΩ pot, linear taper
- Bias trim for the second chip, the same as Bias1. At half (assumed) its input sits at 6.0 V.
- R22, 5.1 kΩ
- Bottom of the Bias2 trim.
- C19, 1 µF electrolytic
- Keeps the signal off the Bias2 trim’s wiper.
- R21, 100 kΩ
- Carries the bias to the second chip’s input.
- IC5, MN3005
- Second MN3005, after the Level trim. With the first chip the delay is 4096 clock periods. Both chips run at IC6’s rate. Swing 2.2 V, assumed.
- R33, 130 kΩ
- Load on output 1 (pin 3).
- R34, 130 kΩ
- Load on output 2 (pin 4).
- R35, 12 kΩ
- Feeds the output loads from the 12 V line.
- C24, 10 µF electrolytic
- Filters the output loads’ supply.
- SR6 Balance, 10 kΩ pot, linear taper
- Balance trim across the second chip’s two outputs. At half it’s 2.5 kΩ in series here. The clock it cancels isn’t modeled.
- R36, 10 kΩ
- First resistor of the filter after the second chip.
- C25, 4 nF
- Filter cap to ground. 4 n on the trace.
- R37, 10 kΩ
- Second filter resistor.
- C26, 39 nF
- Filter cap to TR3’s emitter.
- R38, 10 kΩ
- Third filter resistor.
- C27, 820 pF
- Filter cap to ground at TR3’s base.
- TR3, 2SC1815
- Emitter follower closing the first output filter.
- R39, 10 kΩ
- TR3’s emitter load.
- R40, 10 kΩ
- First resistor of the second output filter.
- C28, 27 nF
- Filter cap to TR4’s emitter.
- R41, 10 kΩ
- Second filter resistor.
- C29, 470 pF
- Filter cap to ground at TR4’s base.
- TR4, 2SC1815
- Emitter follower closing the second output filter.
- R42, 10 kΩ
- TR4’s emitter load.
- C30, 1 µF electrolytic
- Couples the filtered delay into the expander.
- IC2 (9 to 16), NE571 (one half)
- SA571 half wired as an expander. The rectifier and gain cell are fed the delayed signal, and pins 10 and 11 are joined. Every 1 dB at its input is about 2 dB at its output, which undoes the compressor and pushes the delay line’s hiss down when the signal is quiet. NE571 values.
- C31, 220 nF
- The expander’s rectifier cap, the same as the compressor’s so the two track.
- R43, 33 kΩ
- From the expander’s summing node to ground. With the chip’s own resistors it sets the output’s DC near 4.1 V.
- C33, 4.7 µF electrolytic
- Output coupling cap of the expander.
- R44, 100 kΩ
- Holds the footswitch’s input side at 0 V.
- R45, 100 kΩ
- Holds the footswitch’s output side at 0 V, so it doesn’t pop.
- C34, 4.7 µF electrolytic
- Couples the delayed signal to Repeat and D-Level.
- Repeat, 20 kΩ pot, linear taper
- Repeat, 20 kΩ linear. It sets how much of the delay goes back into the compressor, so how many repeats. Full up, the repeats slowly run away, each about 0.4 dB louder than the one before.
- D-Level, 10 kΩ pot, audio taper
- D-Level, 10 kΩ audio taper. It sets how much of the delay is mixed with the dry signal. Full up, the delay goes into the mixer through the same 10 kΩ as the dry.
- C35, 4.7 µF electrolytic
- Couples the D-Level wiper into the mixer.
- R46, 10 kΩ
- Mixing resistor for the delay.
- C39, 4.7 µF
- Non-polar cap carrying the dry signal from IC1a to the mixer.
- R52, 10 kΩ
- Mixing resistor for the dry signal.
- IC1b, JRC4558D
- Output mixer, inverting, with de-emphasis. Its gain is 1 for the lows and falls to about a sixth (−15.6 dB) in the treble, which undoes IC1a’s lift on both the dry and the delay.
- R49, 3.3 kΩ
- Holds IC1b’s + input on the 6 V line.
- R48, 10 kΩ
- IC1b’s feedback resistor.
- C36, 33 nF
- De-emphasis cap, the mirror of C3.
- R47, 2 kΩ
- De-emphasis resistor, the mirror of R5. With C36 it lowers the gain in the treble.
- C37, 470 pF
- Small cap across R48.
- C38, 10 µF electrolytic
- Output coupling cap.
- R50, 470 Ω
- In series with the output.
- R51, 100 kΩ
- Holds the output at 0 V so the jack doesn’t pop.
- R32, 2 kΩ
- Feeds the 8.2 V zener from the 12 V line.
- D4, 8.2 V zener, in breakdown
- An 8.2 V zener. It holds the top of D-Time steady, so the delay doesn’t move with the supply.
- C23, 10 µF electrolytic
- Filters the 8.2 V line.
- R31, 10 Ω
- Small resistor between the 8.2 V line and D-Time.
- D-Time, 10 kΩ pot, reverse audio taper
- D-Time, 10 kΩ reverse audio (“AntiLog” on the trace), from the 8.2 V line down to the Clock trim. Turned up, its wiper voltage falls, TR7 pulls less current and the clock slows. The delay is about 19 ms at 0, 165 ms at a quarter, 384 ms at half, 521 ms at three quarters and 578 ms full up.
- SR1 Clock, 20 kΩ pot, linear taper
- Clock trim, 20 kΩ as a variable resistor under D-Time. It lifts the bottom of D-Time’s range, so it sets the longest delay. At 0 (assumed), the delay with D-Time full up is about 580 ms, close to the 600 ms listed for the unit. At 2 kΩ the longest delay is about 300 ms.
- R30, 1 MΩ
- Turns D-Time’s wiper voltage into a small current, up to about 7.5 µA, into R28.
- C22, 100 nF
- Tantalum cap. With R30 it smooths D-Time, so the delay glides over about a tenth of a second when the knob moves.
- R28, 8.1 kΩ
- R30’s current through it sets how far TR7’s base sits above TR6’s, up to about 60 mV.
- R29, 2.2 MΩ
- Feeds TR6 about 5 µA from the 12 V line.
- TR6, 2SC1815
- A transistor with its base on its collector, as a diode. TR7 copies its current, times e^(V / 26 mV), V the drop across R28.
- TR7, 2SC1815
- Pulls the current that runs the clock’s timing cap down. Every 18 mV more across R28 doubles it, so its current runs from about 4 to 125 µA.
- R27, 10 kΩ
- In series with TR7’s collector.
- R25, 330 Ω
- From the timing node to TR5’s collector and R27. TR5 refills C21 through it each cycle (inside the clock part here).
- IC6, MN3101
- MN3101 clock chip. Its timing cap is C21, 47 pF, modeled inside this part, and so is TR5, which refills C21 each cycle. The current TR7 pulls through R27 and R25 runs C21 down, and the clock runs at about that current / (2.2 × 5.7 V × 47 pF), from about 7 to 215 kHz. It clocks IC5, and IC3 through IC4.
About this version
- Two MN3005s, as traced
- Negative ground, on a 12 V adapter. The op-amps work around a 6 V line from R54 and R55.
Sources
- M. Chittum, traced schematic of an early two-chip unit, 2009
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.