Discrete op-amp distortion with a two-knob EQ and a treble enhancer, 1986 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Ibanez DS10 Distortion Charger.
An emitter follower, a transistor gain stage and a gain stage built from four transistors, then silicon diodes to ground, a passive Low and High network, and a JFET stage. An op-amp filter picks out the treble above about 5 kHz, and Enhance mixes it back in through a second op-amp.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 buffers the guitar. C14 into Q10βs low input cuts the bass below about 1 kHz. Q10βs gain is about 25 dB at 1 kHz, and its collector sits near 1.8 V, so a hard pick clips it on the low side first. Q8, Q9 and Q7 work as an op-amp, with Distortion setting its gain from 1 to about 22. D5 and D6 clip the result to ground at about 0.6 V either way. Low and High are a passive network, so the level drops there, and Q3 makes up a little of it after Level. IC1B passes only the treble, above about 5 kHz. Enhance feeds that treble into IC1Aβs minus input, so it comes back inverted, and turning Enhance up also raises IC1Aβs gain for the whole signal. The model leaves out the electronic bypass and Output B, which carries the same signal with the effect on.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R14, 10βkΞ©
- Top of the 4.5 V reference divider.
- R13, 10βkΞ©
- Bottom of the reference divider.
- C07, 47βΒ΅F electrolytic
- Filters the 4.5 V reference.
- C01, 100βnF
- Input coupling cap.
- R01, 1βkΞ©
- Input series resistor.
- R03, 510βkΞ©
- Biases Q1βs base from its divider and sets the input impedance near 510 kΞ©.
- R02, 9.1βkΞ©
- Top of Q1βs bias divider, about 6.3 V.
- R04, 22βkΞ©
- Bottom of Q1βs bias divider.
- C02, 10βΒ΅F electrolytic
- Filters Q1βs bias divider.
- Q1, 2SC1815
- Input buffer, an emitter follower.
- R07, 10βkΞ©
- Q1βs emitter resistor.
- C04, 1βΒ΅F
- Coupling cap toward the gain stages. Q5, a JFET switch between it and C14, is drawn as a wire.
- R09, 510βkΞ©
- Holds the switchβs side of C04 at 4.5 V.
- C14, 47βnF
- Coupling cap into Q10. Q10βs input is only a few kΞ©, so C14 cuts the bass below about 1 kHz.
- R21, 100βkΞ©
- From Q10βs base to ground. With R20 it sets Q10βs collector near 1.8 V.
- R20, 100βkΞ©
- From Q10βs collector to its base. It biases Q10 and pulls its gain down as the collector swings.
- C13, 220βpF
- Across R20. It rolls off Q10βs gain in the high treble.
- R24, 10βkΞ©
- Q10βs collector resistor.
- Q10, 2SC1815
- First gain stage, a common-emitter stage of about 25 dB at 1 kHz. Its collector sits near 1.8 V, so it runs out of room on the low side first.
- R26, 220βΞ©
- Q10βs emitter resistor. With R24 it sets the most gain Q10 can have.
- C11, 47βnF
- Coupling cap into the discrete op-amp.
- R27, 100βkΞ©
- Biases Q8βs base at 4.5 V.
- Q8, 2SA1015-GR
- PNP input pair, the plus input. Its collector drives Q7.
- Q9, 2SA1015-GR
- PNP input pair, the minus input, where the feedback comes in.
- R23, 10βkΞ©
- Feeds the input pairβs emitters from 9 V.
- R19, 4.7βkΞ©
- Q8βs collector load, from Q7βs base to ground.
- Q7, 2SC1815
- The discrete op-ampβs output transistor, a common-emitter stage.
- C10, 47βpF
- From Q7βs base to its collector. It keeps the loop stable and rolls off the top end.
- R18, 10βkΞ©
- Q7βs collector resistor.
- Distortion, 100βkΞ© pot, linear taper
- Distortion, 100 kΞ© linear. The track from the output end to the wiper is the feedback, the rest plus R83 is the gain leg, so the gain runs from 1 at 0 to about 22 at full.
- R22, 10βkΞ©
- From the Distortion wiper to Q9βs base.
- R83, 4.7βkΞ©
- The least resistance in the gain leg. It sets the top gain.
- C38, 2.2βΒ΅F electrolytic
- In series with the gain leg, so the stageβs DC gain is 1. With Distortion at full it cuts the gain below about 15 Hz.
- C36, 22βnF
- Coupling cap to the diodes.
- R82, 22βkΞ©
- Feeds the diodes and limits their current.
- D5, D6, 1N914 / 1N4148, one each way
- 1S1588 silicon diodes back to back to ground. They hold the signal to about 0.6 V either way.
- R81, 47βkΞ©
- Top of the Low network.
- C35, 4.7βnF
- Across the Low potβs top half. It lets the mids and treble past the pot.
- Low, 500βkΞ© pot, reverse audio taper
- Low, 500 kΞ© reverse audio. Turned up, its wiper moves toward R81 and more bass passes.
- C31, 22βnF
- Across the Low potβs bottom half.
- R85, 4.7βkΞ©
- Bottom of the Low network.
- R84, 22βkΞ©
- Joins the Low wiper to the High wiper.
- C37, 1βnF
- Feeds the treble from the diodes to the High pot.
- High, 500βkΞ© pot, linear taper
- High, 500 kΞ© linear. Turned up, its wiper moves toward C37 and more treble passes.
- C32, 6.8βnF
- Bottom of the High pot.
- Level, 500βkΞ© pot, linear taper
- Level, 500 kΞ© linear, from the tone network to ground.
- C08, 47βnF
- Coupling cap into Q3.
- R17, 510βkΞ©
- Holds Q3βs gate at 0 V.
- Q3, 2SK30A-O
- Make-up gain stage after Level, a 2SK118 JFET with its source resistor unbypassed. Modeled as a 2SK30A of the same grade.
- R16, 2.2βkΞ©
- Q3βs source resistor. It sets Q3βs current and holds its gain near 1.6.
- R15, 5.1βkΞ©
- Q3βs drain resistor. The scan reads 510 kΞ©, which would starve Q3, so 5.1 kΞ© is assumed.
- C09, 100βnF
- Coupling cap out of Q3. Q12, a JFET switch after it, is drawn as a wire.
- R08, 510βkΞ©
- Holds the effect signalβs line at 4.5 V.
- C21, 1βnF
- First cap of the treble filter.
- R31, 33βkΞ©
- From between the filterβs caps to IC1Bβs output.
- C22, 1βnF
- Second cap of the treble filter.
- R32, 33βkΞ©
- Biases IC1Bβs plus input at 4.5 V.
- IC1B, JRC4558D
- A two-cap high-pass filter. It passes the treble above about 5 kHz and cuts whatβs under it by 12 dB for each halving of the frequency.
- R30, 13βkΞ©
- IC1Bβs feedback resistor.
- R29, 22βkΞ©
- With C12, raises IC1Bβs gain to about 1.6 above about 1.5 kHz.
- C12, 4.7βnF
- In series with R29 to ground.
- C34, 15βnF
- Feeds the treble to the Enhance wiper.
- Enhance, 100βkΞ© pot, reverse audio taper
- Enhance, 100 kΞ© reverse audio. Turned up, its wiper moves toward R41, so more treble reaches IC1A and IC1Aβs gain rises, about 8 dB at 1 kHz. Turned down, R80 and C33 bleed the treble to ground.
- R80, 1βkΞ©
- With C33, bleeds the treble to ground with Enhance turned down.
- C33, 22βΒ΅F electrolytic
- In series with R80 to ground.
- R41, 27βkΞ©
- Into IC1Aβs minus input, so the treble comes back inverted.
- R38, 100βkΞ©
- IC1Aβs feedback resistor.
- C26, 220βpF
- Across R38. It rolls off above about 7 kHz.
- C23, 47βnF
- Coupling cap from the effect signal to IC1A.
- R35, 100βkΞ©
- Top half of the divider into IC1Aβs plus input.
- R36, 100βkΞ©
- Bottom half of the divider, to 4.5 V.
- IC1A, JRC4558D
- Mixer. The main signal goes to its plus input at half level, the treble from Enhance to its minus input.
- C27, 220βnF
- Output coupling cap. Q13, a JFET switch after it, is drawn as a wire.
- R28, 510βkΞ©
- Holds Output Aβs line at 4.5 V.
- C25, 100βnF
- Coupling cap into Q17.
- R33, 510βkΞ©
- Biases Q17βs base at 4.5 V.
- Q17, 2SC1815
- Output Aβs buffer, an emitter follower.
- R37, 10βkΞ©
- Q17βs emitter resistor.
- C30, 10βΒ΅F electrolytic
- Output coupling cap.
- R39, 470βΞ©
- In series at the output.
- R42, 100βkΞ©
- Output pulldown.
About this version
- Factory values
- The factory drawing PCB-DS-0101A. 2SC1815 and 2SA1015 transistors, an NJM4558D, 1S1588 diodes (the libraryβs 1N914). R15 is set at 5.1 kΞ©, see its note.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.