One 6SJ7 pentode stage into a 6V6, 1953 style

Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.

Start here

Modeled after the Fender 5C1 Champ.

One 6SJ7 pentode stage, the volume and one 6V6, single-ended in cathode bias. There is no tone control and no feedback.

Input

Add

Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.

How it’s played
Tap a part to change its value, or a wire to probe it. To add or take out parts, open Modify this circuit, below. Red numbers are DC voltages to ground, not warnings. Scroll or drag to see the whole circuit. Pinch to zoom.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.

Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.

Add a part

Tap where each leg goes. Tap both ends of a part to put the new one across that part.

Change a part

With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.

Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.

Change a wire

With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.

With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.

Keep and share

Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.

Test tone for the graphs
The graphs use a steady tone. Play sounds a plucked string that dies away.

Input

pickup, unloadedat the pedal input

Output

at the amp input

Probe

Spectrum

Frequency response

What the curves mean

The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.

Output

Bias

every voltage and current at rest

What to listen for The guitar reaches the 6SJ7’s grid through 75 kΩ and .02 µF. The cathode is grounded, so the tube biases itself. A little grid current flows through the 5 MΩ grid leak and holds the grid about 0.85 V negative. The screen runs at about 24 V through 2 MΩ, so the tube runs at a low current, and the plate sits near 152 V. The volume feeds the 6V6’s grid directly. There is no driver stage, no tone control and no feedback. The 6V6’s screen shares the 25 kΩ node with the preamp, so it sits about 70 V under its plate. On the whole amp a steady A2 at 200 mV reaches about 1.9 V rms at the speaker with the volume at 5, and about 5.8 V at full, where the 6V6 clips and the harmonics rise to about 21 %. The transformers are typical, and the drawing shows no voltages.

Download.

Parts and what they do

Stock values for the As drawn version. Tap a part on the schematic to change it.

R1, 75 kΩ
Input 1’s resistor, 75 kΩ.
R2, 75 kΩ
Input 2’s resistor, 75 kΩ. With nothing in input 1 that tip is grounded, so the two make a divider and input 2 is about 6 dB quieter.
C1, 20 nF
Coupling cap into the 6SJ7’s grid.
R3, 5 MΩ
Grid leak, 5 MΩ. The cathode is grounded, so the tube’s bias comes from the little grid current that flows through this resistor.
V1, 6SJ7
6SJ7 pentode, the only gain stage ahead of the 6V6. Its cathode is grounded.
R4, 2 MΩ
Screen resistor, 2 MΩ from the 25 kΩ node.
C2, 50 nF
Screen bypass cap.
R5, 250 kΩ
Plate resistor, 250 kΩ from the 25 kΩ node.
C3, 20 nF
Coupling cap from the 6SJ7’s plate to the volume.
Volume, 1 MΩ pot, audio taper
Volume, 1 MΩ. Its wiper is the 6V6’s grid, and the pot is the grid’s path to ground. Audio taper assumed.
V2, 6V6GT
6V6GT, the output tube, single-ended: it carries the whole signal, and its idle current runs through the transformer all the time. Its cathode resistor biases it. Its grid connects straight to the preamp’s volume pot, which is its path to ground.
500, 500 Ω
The cathode resistor. The tube’s current runs through it and lifts the cathode above the grid, and that’s the bias. Driven hard, the tube draws more current on average, so the cathode climbs and the bias goes colder.
25µ, 25 µF electrolytic
Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
500, 500 Ω
Dropping resistor from the reservoir cap to B+, as on the amp’s drawing. The output transformer hangs after it, so the plate’s current runs through it.
8µ, 8 µF electrolytic
Filter cap on B+ after the dropping resistor, where the output transformer hangs.
25k, 25 kΩ
Dropping resistor from the screen supply node to the node for the preamp and the screen, as on the Fender 5C1 Champ drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
8µ, 8 µF electrolytic
Filter cap at the node for the preamp and the screen. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
OT, 5 kΩ to 3.2 Ω, 14.3 H primary, 54.3 mH leakage
The output transformer, 5 kΩ from the plate to B+ into 3.2 Ω, center tap on B+ after the dropping resistor. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
PT, 297 V ac, 60 Hz
One half of the power transformer’s high-voltage winding, 297.3 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
PT, 297 V ac, 60 Hz
The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
PT R, 141 Ω
Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
PT R, 141 Ω
Resistance of the other half. Typical of the part.
V3, 5Y3GT
One plate of the 5Y3GT rectifier. It conducts near the peak of its half of the winding, and its own drop rises with the current, which adds to the sag.
V3, 5Y3GT
The rectifier’s other plate, on the other half cycle.
8µ, 8 µF electrolytic
The reservoir cap. It feeds the dropping resistor, and past it the output transformer’s center tap and everything else. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
Coil R, 3.48 Ω
Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 3.2 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
Coil L, 102 µH
Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
Loss L, 186 µH
With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
Loss R, 5.72 Ω
Limits what Loss L adds to the treble rise.
Loss L2, 852 µH
A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
Loss R2, 876 mΩ
Limits what Loss L2 adds.
Tank R, 33.5 Ω
Height of the bass resonance, about 37 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
Tank L, 8.45 mH
With Tank C, sets the resonance: 74 Hz.
Tank C, 551 µF
With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.

Versions

As drawn
The 6SJ7 preset is fitted to the GE sheet. The transformers are typical, not on the drawing.
Gibson Les Paul Jr, modeled after the Gibson Les Paul Jr
The Gibson Les Paul Jr from the factory drawing: 47 kΩ jack resistors, a 10 MΩ grid leak, a 2.2 MΩ screen resistor and a 220 kΩ plate resistor. In the power amp, 470 Ω and 20 µF on the 6V6’s cathode, 470 Ω and 22 kΩ in the supply. The transformers are the 5C1’s, typical.

How this tool works. Every part is described by an equation, and the whole circuit is solved several times for each audio sample: 192,000 samples a second while you drag a knob, and 384,000 once you let go. Transistors use the standard Ebers-Moll model, with gain, leakage, base resistance, junction capacitance, temperature and the small rise in current with collector voltage (the Early effect). The charge a transistor stores is worked out at its idle point. That is accurate for small signals and rough while the transistor switches hard. Tubes use Koren’s equations, matched to each type’s datasheet, plus grid current. Diodes use the standard diode equation with series resistance. Presets are typical of each type. Caps are ideal, and the battery or HT is a voltage behind a resistance.

Spot an error, or want a circuit added? Email info@swellamps.com. A schematic or a clear photo of one helps. Anything you send may be used to improve these models and our desktop app.

From Swell Amplification, swellamps.com.