Stereo bucket-brigade chorus, 1982 style
Pedal and tube amp circuits, simulated part by part the way an engineerβs circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuitβs knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuitβs notes say which schematic itβs based on.
Modeled after the Boss CE-3 Chorus.
An MN3207 delay chip holds a copy of the guitar about 4 ms behind, and a slow triangle swings that delay through the chipβs MN3102 clock. Output A adds the copy to the dry signal. Output B adds it inverted. The bench plays output A.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. Theyβre lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for A JFET follower takes the guitar in at 1 MΞ©. IC1b lifts the treble about 15 dB, and the mixers cut it back down after the delay, so the chipβs hiss comes down with it. The wet side has a three-pole low-pass near 6.6 kHz before the chip and another after it, each three times as steep as one resistor and cap, so the clockβs steps stay out of the output. The clock runs at 116 to 144 kHz at half Depth, a delay of 3.55 to 4.4 ms. At full Depth it runs 110 to 160 kHz, 3.2 to 4.65 ms, and at 0 the delay holds near 3.9 ms. Rate runs the sweep from about 0.3 to 3.4 times a second, the service notesβ 3 s and 270 ms. Output A adds the dry and wet signals equally. IC2b inverts the wet signal for output B, so the frequencies that cancel at one output add up at the other. The footswitch and its electronic bypass are left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C18, 100βΒ΅F electrolytic
- Bulk cap across the 9 V supply.
- R27, 33βkΞ©
- Feeds Q7βs base. With C15 it smooths the base voltage.
- C15, 10βΒ΅F electrolytic
- Holds Q7βs base steady, so the supply after Q7 carries much less ripple and clock noise.
- Q7, 2SC1815
- Emitter follower that makes the filtered supply for the whole circuit, about 0.9 V under the battery. A 2SC945, modeled as a 2SC1815.
- R64, 4.7βkΞ©
- Top of the bias divider.
- VR3, 10βkΞ© pot, linear taper
- Bias trimmer, 10 kΞ©. Its wiper is the bias line the audio works around, and through Q6 it sets the DC on the delay chipβs input. The service notes set it for the cleanest delay. Here it is at half turn.
- R54, 4.7βkΞ©
- Bottom of the bias divider.
- C20, 47βΒ΅F electrolytic
- Filters the bias line.
- R46, 10βkΞ©
- Top of the LFOβs bias divider.
- R50, 10βkΞ©
- Bottom of the LFOβs bias divider.
- C27, 47βΒ΅F electrolytic
- Filters the LFOβs bias line.
- R2, 10βkΞ©
- In series with the input.
- C1, 47βnF
- Input coupling cap.
- R4, 1βMΞ©
- Biases Q1βs gate from the bias line and sets the input impedance at 1 MΞ©.
- Q1, 2SK30A-Y
- Input buffer, a JFET source follower (2SK30A-Y).
- R3, 10βkΞ©
- Q1βs source load.
- C3, 470βnF electrolytic
- Couples the buffer into the pre-emphasis stage.
- R20, 47βkΞ©
- Input resistor of the pre-emphasis stage.
- C2, 6.8βnF
- With R21 beside R20 it lifts the treble. The lift starts near 410 Hz and levels off near 2.3 kHz.
- R21, 10βkΞ©
- In series with C2. It sets where the treble lift levels off.
- R19, 47βkΞ©
- Feedback resistor of the pre-emphasis stage.
- C4, 100βpF
- Rolls the top end off above about 34 kHz.
- R18, 120βkΞ©
- A second feedback resistor, switched in by the JFET Q2. Q2 is drawn as a wire, taken to be on with the effect on, so R18 sits beside R19 and the stageβs gain is about 0.7 for low notes.
- R16, 10βkΞ©
- Biases the + input from the bias line.
- IC1b, JRC4558D
- Pre-emphasis stage, inverting. Treble goes up about 15 dB before the delay so the chipβs hiss can come down the same amount after it. The dry and wet paths and both outputs start here. Half an NJM4558.
- C10, 33βnF
- Couples the signal into the delay side. With R14 it cuts below about 48 Hz.
- R14, 100βkΞ©
- Holds the filterβs input on the bias line, so Q6 and the delay chipβs input sit at a set DC.
- R22, 10βkΞ©
- First resistor of the low-pass ahead of the delay chip.
- C11, 3.3βnF
- First cap of the low-pass.
- R23, 10βkΞ©
- Low-pass filter resistor.
- C14, 8.2βnF
- Feedback cap from Q6βs emitter. It squares up the low-passβs knee.
- R24, 10βkΞ©
- Low-pass filter resistor.
- C12, 470βpF
- Last cap of the low-pass. With C11, C14 and the three 10 kΞ© it makes a three-pole low-pass near 6.6 kHz, so the clock doesnβt fold high notes back down.
- Q6, 2SC1815
- Emitter follower of the low-pass. It drives the delay chip. A 2SC732, modeled as a 2SC1815.
- R25, 10βkΞ©
- Q6βs emitter load.
- R26, 4.7βkΞ©
- Into the delay chipβs input.
- IC3, MN3207
- MN3207 delay line, 1024 stages. It holds 512 samples and passes each on after 512 clock periods, a few milliseconds here. The two outputs are drawn as one pin. Swing set to 1.5 V for the supply after Q7.
- R39, 56βkΞ©
- Load on the delay chipβs outputs.
- C16, 33βnF
- Couples the delayed signal into the second low-pass.
- R30, 330βkΞ©
- Holds the second filterβs input on the bias line.
- R38, 10βkΞ©
- First resistor of the low-pass after the delay chip.
- C24, 3.3βnF
- First cap of the second low-pass.
- R47, 10βkΞ©
- Low-pass filter resistor.
- C23, 8.2βnF
- Feedback cap from Q8βs emitter.
- R48, 10βkΞ©
- Low-pass filter resistor.
- C22, 470βpF
- Last cap of the second low-pass, the same as the first. It smooths the chipβs steps.
- Q8, 2SC1815
- Emitter follower of the second low-pass. A 2SC732, modeled as a 2SC1815.
- R37, 10βkΞ©
- Q8βs emitter load.
- C21, 68βnF
- Couples the wet signal toward both outputs. With R36 it cuts the wet side below about 50 Hz.
- R35, 1βMΞ©
- Holds the wet line on the bias line.
- R36, 47βkΞ©
- Wet signal into mixer A. The JFET switch Q4 after it is drawn as a wire, since it is on with the effect on.
- R15, 47βkΞ©
- Dry signal into mixer A, equal to R36. The JFET switch Q3 after it is drawn as a wire.
- IC1a, JRC4558D
- Mixer A and de-emphasis. It adds the dry and wet signals and cuts the treble back down. Half an NJM4558.
- R8, 47βkΞ©
- Feedback resistor of mixer A. Against R15 and R36 each input comes through at a gain of 1 for low notes.
- C5, 100βpF
- Rolls the top end off above about 34 kHz.
- C6, 6.8βnF
- With R7 beside R8 it cuts the treble by the same curve the pre-emphasis raised it.
- R7, 10βkΞ©
- In series with C6.
- R6, 470βΞ©
- In series with output A.
- C7, 1βΒ΅F electrolytic
- Output A coupling cap.
- R5, 100βkΞ©
- Holds output A at 0 V so the jack doesnβt pop.
- R31, 47βkΞ©
- Wet signal into IC2b.
- R29, 47βkΞ©
- Feedback resistor of IC2b, equal to R31, so its gain is 1.
- IC2b, JRC4558D
- Inverting amp with a gain of 1. It inverts the wet signal for output B. Half an NJM4558.
- R28, 47βkΞ©
- Inverted wet signal into mixer B, through the JFET switch Q5, drawn as a wire. Q5 is on in Mode I, the only mode on the bench.
- R17, 47βkΞ©
- Dry signal into mixer B.
- IC2a, JRC4558D
- Mixer B and de-emphasis, the same as mixer A. It adds the dry signal and the inverted wet signal. Half an NJM4558.
- R34, 47βkΞ©
- Feedback resistor of mixer B.
- C17, 100βpF
- Rolls the top end off above about 34 kHz.
- C19, 6.8βnF
- With R33 beside R34 it cuts the treble back down.
- R33, 10βkΞ©
- In series with C19.
- R32, 470βΞ©
- In series with output B.
- C8, 1βΒ΅F electrolytic
- Output B coupling cap.
- R9, 100βkΞ©
- Holds output B at 0 V. Nothing is plugged into output B on the bench.
- IC5a, TL022
- Comparator with hysteresis, which means it switches at one level on the way up and a different one on the way down. Its output flips to the other rail each time the triangle reaches a peak, so it puts out a square wave. Half a TL022.
- R49, 33βkΞ©
- From the triangle to the comparator. Against R53 it sets the triangleβs height at about 0.7 of the squareβs.
- R53, 47βkΞ©
- Positive feedback that holds the comparator where it last flipped.
- C29, 10βnF
- From the square to the β input. It slows each flip slightly.
- R51, 100βkΞ©
- Holds the comparatorβs β input on the LFOβs bias line.
- Rate, 100βkΞ© pot, linear taper
- Rate, 100 kΞ© linear. It sets how much of the square reaches the integrator, and that sets how fast the triangle ramps.
- R10, 10βkΞ©
- Under Rate. It sets the slowest sweep.
- R52, 1βMΞ©
- Integrator input resistor. With C28 it sets the rampβs speed.
- C28, 100βnF
- Integrator cap. A smaller cap makes every Rate setting faster.
- IC5b, TL022
- Integrator. The square wave in makes a triangle out. Half a TL022.
- Depth, 100βkΞ© pot, linear taper
- Depth, 100 kΞ© linear. It sets how much of the triangle reaches the clock, and that sets how far the delay swings. At 0 the delay holds still.
- R45, 220βkΞ©
- With C26 it rounds the triangleβs corners (about 72 Hz).
- C26, 10βnF
- Smoothing cap on Q10βs base.
- Q10, 2SC1815
- Emitter follower for the LFO. A 2SC945, modeled as a 2SC1815.
- R44, 4.7βkΞ©
- Top of a divider that halves Q10βs emitter voltage.
- R43, 4.7βkΞ©
- Bottom of that divider.
- D12, 1N914 / 1N4148
- Feeds the LFO into the clockβs timing node. The higher the LFO voltage, the more current it adds, so the clock runs faster and the delay gets shorter. 1SS133, modeled as a 1N914.
- RCV, 56βkΞ©
- Stand-in, not on the pedal. It sizes the LFOβs pull on the model clock, as on the benchβs CE-2.
- R40, 150βkΞ©
- Timing resistor. It charges C25 and sets the slowest clock, with the LFO at the bottom of its swing.
- IC4, MN3102
- MN3102 clock. Its timing cap C25 is 47 pF. More current into the timing pin runs the clock faster. Q9, D11, R41 and R42, which empty C25 each cycle, are part of the clock and not drawn.
About this version
- As drawn
- Negative ground, 9 V. Q7 filters the battery into an 8.1 V supply for the whole circuit. The audio works around the bias line VR3 sets, about 4 V.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Donβt rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.