Short-line bucket-brigade chorus, 1982 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Korg CHR-1 Chorus.
An MN3009 delay chip, only 256 stages, holds a copy of the guitar 2 to 5 ms behind. An LFO swings that delay through the clock, and the copy is mixed back with the dry signal. Mode 2 feeds the copy back into its own input.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC4b lifts the treble ahead of the delay chip, and the low-passes after it bring the copy back down. The clock runs from about 26 to 65 kHz, set by how much current Q2 pulls from its timing node. Three diodes in Q2’s emitter mean Q2 only turns on in the top part of the LFO’s swing, so the delay sits longer near its long end and moves quickly through the short end. At half Intensity the delay swings from about 3.4 to 4.6 ms. Speed runs the LFO from about 0.2 to 7.9 times a second, and at fast settings R49 and C33 smooth it so the swing gets smaller. The mix is about 64 % dry and 36 % wet. In Mode 2 the copy also goes back into IC4b through C24 and R44, so each echo comes back again and the comb gets deeper. The footswitch and the direct out are left out of what plays.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C1, 100 µF electrolytic
- Bulk cap across the 9 V supply.
- R1, 33 Ω
- Feeds the delay chip and its clock from the supply. With C3 it keeps the clock’s current spikes off the audio.
- C3, 10 µF electrolytic
- Filters the 8.9 V line.
- R19, 22 kΩ
- Top of the half-supply divider.
- R5, 22 kΩ
- Bottom of the half-supply divider.
- C2, 100 µF electrolytic
- Filters the half-supply line, about 4.5 V. The audio works around it.
- R46, 5.6 kΩ
- Feeds the 5.1 V zener for the LFO.
- D7, 5.1 V zener, in breakdown
- RD5.1EB zener. It holds the LFO’s reference at about 5.1 V, so the sweep doesn’t change as the battery runs down.
- C27, 220 µF electrolytic
- Filters the 5.1 V line.
- C22, 47 nF
- Input coupling cap.
- R42, 10 kΩ
- In series with the buffer’s input.
- R43, 1 MΩ
- Biases the buffer’s input at half the supply and sets the input impedance at 1 MΩ.
- IC4a, TL072
- Input buffer, a follower. Half a TL072.
- C30, 68 nF
- Couples the buffer into the amp stage.
- R54, 27 kΩ
- Input resistor of the amp stage, with R53 in series. Against R52 it sets a gain of about 1.55 for low notes.
- C31, 22 nF
- Across R54. Above about 270 Hz it bypasses R54, so the treble gets up to about 19 dB more gain.
- R53, 3.3 kΩ
- In series with R54 and C31. It sets where the treble lift levels off, near 2.2 kHz.
- R52, 47 kΩ
- Feedback resistor of the amp stage.
- C29, 100 pF
- Rolls the top end off above about 34 kHz.
- IC4b, TL072
- Amp and pre-emphasis stage, inverting. It lifts the treble before the delay chip. Half a TL072.
- C24, 6.8 nF
- Brings the wet signal back into the amp stage, the feedback that Mode sets.
- R44, 15 kΩ
- In series with C24 in the feedback path.
- R35, 470 kΩ
- In series with the feedback in Mode 1, so only a little of the wet signal comes back. In Mode 2 the switch shorts it.
- R34, 2 kΩ
- Into the low-pass ahead of the delay chip.
- C19, 10 nF
- First cap of the low-pass.
- R30, 10 kΩ
- Low-pass filter resistor.
- C12, 3.3 nF
- Feedback cap from Q4’s emitter. It squares up the low-pass’s knee.
- R29, 10 kΩ
- Low-pass filter resistor.
- C15, 1.2 nF
- Last cap of the low-pass, which keeps the clock from folding high notes back down.
- Q4, 2SC1815
- Emitter follower of the low-pass. It drives the delay chip. A 2SC2785, modeled as a 2SC1815.
- R28, 10 kΩ
- Q4’s emitter load.
- C14, 1 µF
- Couples the signal into the delay chip. A non-polar cap.
- VR3, 47 kΩ pot, linear taper
- Bias trimmer, 47 kΩ. It sets the DC on the delay chip’s input. The service notes set it for a symmetrical wave. Here it is at half turn, about 4.4 V.
- C18, 10 µF electrolytic
- Filters the bias trimmer’s wiper.
- R27, 100 kΩ
- Brings the bias to the delay chip’s input.
- IC2, MN3009
- MN3009 delay line, 256 stages. It holds 128 samples and passes each on after 128 clock periods, 2 to 5 ms here. The two outputs are drawn as one pin.
- R20, 100 kΩ
- Load on the delay chip’s first output, to the 8.9 V line. Both outputs are one pin here, so R20 and R22 sit side by side.
- R22, 100 kΩ
- Load on the delay chip’s second output.
- R21, 5.1 kΩ
- Mixes the first output into the second low-pass. With R23 it adds the two outputs, which cancels much of the clock’s step.
- R23, 5.1 kΩ
- Mixes the second output into the second low-pass.
- C9, 1 nF
- First cap of the second low-pass.
- R10, 22 kΩ
- Second low-pass resistor.
- C4, 10 nF
- With R2, a cap to ground that trims the top of the wet signal.
- R2, 4.7 kΩ
- In series with C4. It sets how far C4 can cut the treble.
- R11, 10 kΩ
- Low-pass filter resistor.
- C6, 3.3 nF
- Feedback cap from Q3’s emitter.
- R12, 10 kΩ
- Low-pass filter resistor.
- C7, 1.2 nF
- Last cap of the second low-pass.
- Q3, 2SC1815
- Emitter follower of the second low-pass. A 2SC2785, modeled as a 2SC1815.
- R13, 10 kΩ
- Q3’s emitter load.
- C16, 1 µF electrolytic
- Couples the wet signal into IC3a.
- R31, 24 kΩ
- Input resistor of IC3a’s low-pass.
- C20, 2.7 nF
- Cap of IC3a’s low-pass.
- R25, 12 kΩ
- Into IC3a’s − input.
- R32, 24 kΩ
- Feedback resistor of IC3a’s low-pass. Against R31 the gain is 1, inverted.
- C13, 1 nF
- Feedback cap of IC3a’s low-pass. With C20 it makes a two-pole low-pass near 4 kHz.
- IC3a, JRC4558D
- Two-pole low-pass for the wet signal, inverting. Its output is the wet signal for the mix and for Mode’s feedback. Half a JRC4558.
- C10, 1 µF electrolytic
- Couples the wet signal toward the mix.
- R14, 10 kΩ
- Holds the wet side at 0 V DC.
- C23, 10 µF electrolytic
- Couples the dry signal from the buffer toward the mix, the direct out and the bypass.
- R38, 10 kΩ
- Holds the dry line at 0 V DC.
- R15, 47 kΩ
- Wet signal into the mix.
- R16, 27 kΩ
- Dry signal into the mix. Against R15 the mix is about 64 % dry and 36 % wet.
- C11, 1 µF electrolytic
- Couples the mix into IC3b.
- R18, 100 kΩ
- Biases IC3b’s input at half the supply.
- C8, 100 pF
- Trims radio-frequency hash at IC3b’s input.
- R17, 10 kΩ
- Sets IC3b’s gain with R26.
- R26, 5.6 kΩ
- Feedback resistor of IC3b. Its gain is 1 + 5.6 / 10, about 1.56.
- IC3b, JRC4558D
- Mix amp, non-inverting. Half a JRC4558.
- C21, 1 µF electrolytic
- Output coupling cap.
- R33, 10 kΩ
- Holds the output at 0 V so the jack doesn’t pop.
- R36, 470 Ω
- In series with the output, through the footswitch’s effect side.
- R39, 470 Ω
- Feeds the dry signal to the direct out jack. Nothing is plugged in there on the bench.
- Speed, 500 kΩ pot, reverse audio taper
- Speed, 500 kΩ reverse audio, used as a variable resistor in series with R45. It charges C26 from IC5a’s output. Turned up, there’s less resistance and the LFO runs faster.
- R45, 10 kΩ
- In series with Speed. It sets the fastest sweep.
- C26, 10 µF electrolytic
- The LFO’s timing cap, a 10 µF tantalum. It charges and discharges between the comparator’s two switching levels.
- R47, 150 kΩ
- From the timing cap to IC5a’s − input.
- C28, 10 nF
- From IC5a’s output to its − input. It slows each flip slightly.
- R51, 560 kΩ
- Positive feedback that holds IC5a where it last flipped. Against R50 it sets the switching levels about a fifth of the output’s swing either side of 5.1 V.
- R50, 150 kΩ
- From IC5a’s + input to the 5.1 V line.
- IC5a, TL062 (low power)
- Comparator with hysteresis, which means it switches at one level on the way up and a different one on the way down. It flips each time C26 reaches a switching level, so C26 ramps up and down. Half a TL062.
- R49, 1.5 MΩ
- With C33 it smooths the ramp on C26.
- C33, 47 nF
- Smoothing cap after R49.
- R57, 120 kΩ
- Sets IC5b’s gain with R55.
- R55, 220 kΩ
- Feedback resistor of IC5b. Its gain is 1 + 220 / 120, about 2.8, around 5.1 V.
- IC5b, TL062 (low power)
- Amplifies the smoothed ramp into the LFO that steers the clock. Half a TL062.
- Intensity, 100 kΩ pot, linear taper
- Intensity, 100 kΩ linear, from the LFO to the 5.1 V line. Its wiper sends the LFO to Q2 through R4, so it sets how far the delay swings.
- VR2, 22 kΩ pot, linear taper
- Clock maximum trimmer, 22 kΩ. Its wiper sets Q2’s DC through R24, so it sets the fastest clock.
- R4, 470 kΩ
- From Intensity’s wiper to Q2’s base.
- R24, 100 kΩ
- From VR2’s wiper to Q2’s base.
- Q2, 2SC1815
- Pulls current out of the clock’s timing node, more as its base voltage rises, so the clock runs faster and the delay gets shorter. A 2SC2785, modeled as a 2SC1815.
- R8, 100 Ω
- Q2’s emitter resistor.
- D2, D3, D4, 3 × 1N914 / 1N4148 one way
- Three 1S1555 diodes in Q2’s emitter. Q2 turns on only once its base is about 2.3 V over ground. Modeled as 1N914s.
- R9, 4.7 kΩ
- With VR1, a steady path out of the timing node. It sets the slowest clock.
- VR1, 470 kΩ pot, linear taper
- Clock minimum trimmer, 470 kΩ, used as a variable resistor.
- IC1, MN3101
- MN3101 clock. Its timing cap C5 is 220 pF. The more current Q2 and R9 pull out of the timing node, the faster the clock runs. Q1, R3, R6 and R7 around the chip’s oscillator are inside this part.
About this version
- As drawn
- Negative ground, 9 V. The audio works around half the supply from R19 and R5. The LFO runs from a 5.1 V zener line. Trimmers set as the service manual’s adjustment.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.