Single-ended 50C5 practice amp with supply tremolo, mid 1960s style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Kent 5999.
A 12AU6 pentode on grid-leak bias into one 50C5, single-ended, with a silicon half-wave supply off the mains. The tremolo oscillator’s plate swings the preamp’s supply through the Strength pot.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for The 12AU6 runs with a 1 MΩ plate resistor, and a 3.3 MΩ screen resistor, on a fraction of a milliamp, and its grid biases itself through 15 MΩ. A .05 µF and a 680 kΩ in series sit across the screen resistor, so the tremolo’s slow swing reaches the screen more strongly than through the 3.3 MΩ. Its supply comes off the wiper of the Strength pot, which carries the tremolo oscillator’s plate current. Turned up, the wiper moves toward the oscillator’s plate, so the preamp’s supply rises and falls a few times a second and its gain follows. The Tone control is a .1 µF cap from the 50C5’s plate through a 50 kΩ pot to B+, a treble cut across the output transformer. The 50C5 idles in class A on about 120 V.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- .05µ, 50 nF
- Input coupling cap. It also holds the grid-leak bias, since grid current charges it negative.
- 15M, 15 MΩ
- Grid leak, 15 MΩ. The cathode is grounded, so the grid’s own small current through it sets the bias, about a volt negative.
- V1, 6AU6 / EF94
- 12AU6 pentode, the only preamp stage. Cathode and suppressor grounded.
- 1M, 1 MΩ
- Plate resistor, 1 MΩ from the Strength pot’s wiper.
- 3.3M, 3.3 MΩ
- Screen resistor, 3.3 MΩ from the Strength pot’s wiper. It alone sets the screen’s DC, about 36 V, so the tube runs on a fraction of a milliamp.
- .05µ, 50 nF
- Screen bypass cap.
- .05µ, 50 nF
- With the 680 kΩ, a network across the 3.3 MΩ screen resistor. It passes the Strength wiper’s slow swing to the screen through 680 kΩ in place of 3.3 MΩ, so the screen follows the tremolo more strongly. It carries no DC.
- 680k, 680 kΩ
- In series with the .05 µF, from the Strength wiper to the screen, across the 3.3 MΩ. Above about 5 Hz the pair passes the swing as a 680 kΩ path.
- .05µ, 50 nF
- Coupling cap to the Volume.
- Vol 3M, 3 MΩ pot, audio taper
- Volume, 3 MΩ. Its wiper is the 50C5’s grid, and the pot is that grid’s path to ground. Audio taper is assumed.
- Strength 250k, 250 kΩ pot, linear taper
- Tremolo Strength, 250 kΩ, from the 40 µF node to the oscillator’s plate. The oscillator’s plate current runs through the whole track. The wiper feeds the 12AU6. Turned up, it moves toward the oscillator’s plate, so the 12AU6’s supply swings more. Linear taper and more clockwise are assumed.
- .1µ, 100 nF
- The Tone control’s cap, from the 50C5’s plate to the Tone pot’s wiper.
- Tone 50k, 50 kΩ pot, audio taper
- Tone, 50 kΩ, a variable resistor from the cap to B+. With little resistance the cap bleeds the treble off the plate. Turned up, more resistance goes in series and it gets brighter. Audio taper and brighter clockwise are assumed.
- V3, 6AV6
- The triode of V3, a 12AV6, the tremolo’s oscillator. A ladder of three caps from its plate back to its grid turns the plate’s swing round by half a cycle at a few hertz, so the stage oscillates there. Its plate load is the whole Strength pot.
- .03µ, 30 nF
- First cap of the ladder, from the oscillator’s plate.
- 100k, 100 kΩ
- The ladder’s first leg, 100 kΩ to the Speed pot’s wiper.
- Speed 1M, 1 MΩ pot, reverse audio taper
- Speed, 1 MΩ, a variable resistor under the 100 kΩ. Turned up, there’s less track in the circuit and the oscillator runs faster. A reverse taper is assumed so it changes evenly as it turns, and faster clockwise.
- .01µ, 10 nF
- Second cap of the ladder.
- 1M, 1 MΩ
- The ladder’s second leg, 1 MΩ to ground.
- .01µ, 10 nF
- Last cap of the ladder, into the oscillator’s grid.
- 15M, 15 MΩ
- The oscillator’s grid leak, 15 MΩ to ground.
- V2, 50L6GT
- 50C5, the output tube, single-ended: it carries the whole signal, and its idle current runs through the transformer all the time. Its cathode resistor biases it. Its grid connects straight to the preamp’s volume pot, which is its path to ground.
- 150, 150 Ω
- The cathode resistor. The tube’s current runs through it and lifts the cathode above the grid, and that’s the bias. Driven hard, the tube draws more current on average, so the cathode climbs and the bias goes colder.
- 20µ, 20 µF electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 680, 680 Ω
- Dropping resistor from B+ to the screen supply. The screens sit slightly below the plates.
- 40µ, 40 µF electrolytic
- Filter cap on the screen supply.
- OT, 2.5 kΩ to 3.2 Ω, 4.5 H primary, 40 mH leakage
- The output transformer, 2.5 kΩ from the plate to B+ into 3.2 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 117 V ac, 60 Hz
- The transformer’s high-voltage winding, 117 V ac with one end grounded, as a sine source at the mains frequency. Turn it up and every voltage in the amp goes up, the same as with a higher wall voltage.
- PT R, 47 Ω
- The winding’s resistance, estimated. It and the rectifier limit the charging current into the reservoir cap.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- 60µ, 60 µF electrolytic
- The reservoir cap. It feeds the output transformer’s B+ end. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 3.48 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 3.2 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 102 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 186 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 5.72 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 852 µH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 876 mΩ
- Limits what Loss L2 adds.
- Tank R, 33.5 Ω
- Height of the bass resonance, about 37 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 8.45 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 551 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- As drawn
- Values from the factory drawing. The 12AU6 uses the 6AU6 model, the 12AV6 the 6AV6’s, and the 50C5 the 50L6GT’s.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.