Two-channel 20 W EL84 tube amp, 1969 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Marshall 2022 20 Watt Lead.
Two channels, each one triode of a 12AX7 into its own volume and tone pots. The two volumes mix through 680 kΩ resistors straight into the phase inverter, so there is only one gain stage ahead of two EL84s.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Each channel has one gain stage. Its volume and tone pots feed a 680 kΩ mixing resistor, and the mix goes straight to the phase inverter’s grid. Tone 1 and Tone 2 are brighter clockwise. Clockwise, a 500 pF cap bypasses the top of the volume pot. Counterclockwise, a 10 nF cap pulls the treble at the volume’s top to ground. On the Lead, channel 2 also has a 5 nF bright cap across its volume and 500 pF across its mixing resistor. With so little preamp gain, the breakup comes from the phase inverter and the two EL84s. On Preamp only, you hear the signal as it reaches the phase inverter.
Download.
Parts and what they do
Stock values for the 2022 Lead version. Tap a part on the schematic to change it.
- R1A, 68 kΩ
- Channel 1’s input 1 resistor into the grid. With nothing plugged into input 2, this resistor and input 2’s resistor are in parallel, so a guitar in input 1 goes through 34 kΩ to the grid. That is enough to stop radio pickup and too little to cut treble.
- R3A, 68 kΩ
- Channel 1’s input 2 resistor into the grid. With nothing plugged into input 1, input 1’s tip is grounded, and the two 68 kΩ resistors form a divider. Input 2 is about 6 dB quieter and loads the guitar with 136 kΩ.
- R2A, 1 MΩ
- Input 1’s 1 MΩ to ground. It sets the load a guitar in input 1 sees, and with a patch lead in input 1 it is the end of the lead’s path.
- R1B, 68 kΩ
- Channel 2’s input 1 resistor into the grid. With nothing plugged into input 2, this resistor and input 2’s resistor are in parallel, so a guitar in input 1 goes through 34 kΩ to the grid. That is enough to stop radio pickup and too little to cut treble.
- R3B, 68 kΩ
- Channel 2’s input 2 resistor into the grid. With nothing plugged into input 1, input 1’s tip is grounded, and the two 68 kΩ resistors form a divider. Input 2 is about 6 dB quieter and loads the guitar with 136 kΩ.
- R2B, 1 MΩ
- Input 1’s 1 MΩ to ground. It sets the load a guitar in input 1 sees, and with a patch lead in input 1 it is the end of the lead’s path.
- 10k, 10 kΩ
- Dropping resistor, 10 kΩ 1 W, from the inverter’s 340 V node to V1’s node.
- 32µ, 32 µF electrolytic
- Filter cap on V1’s node, 320 V on the drawing.
- V1a, 12AX7 / ECC83 / 7025
- Channel 1’s gain stage, the only one before the phase inverter.
- RP1, 100 kΩ
- Channel 1 plate load, 100 kΩ. The drawing shows 200 V on the plate.
- C1A, 22 nF
- Channel 1 coupling cap to the volume. Into 1 MΩ it passes the full bass.
- Volume 1, 1 MΩ pot, audio taper
- Channel 1 volume, 1 MΩ.
- Tone 1, 1 MΩ pot, audio taper
- Channel 1 tone, 1 MΩ, its wiper on the volume’s top. Clockwise, the 500 pF end is close and the 10 nF end is far, so more treble passes the volume. Counterclockwise, the 10 nF is close and pulls the treble to ground.
- C5A, 500 pF
- From one end of Tone 1 to the volume’s wiper. With the tone up, it passes treble around the top of the volume pot.
- C6A, 10 nF
- From the other end of Tone 1 to ground. With the tone down, it cuts treble at the volume’s top.
- RM1, 680 kΩ
- Channel 1 mixing resistor, 680 kΩ into the phase inverter’s grid. With RM2 it mixes the channels and keeps each volume from shorting the other.
- V1b, 12AX7 / ECC83 / 7025
- Channel 2’s gain stage. It shares the cathode resistor and bypass cap with channel 1.
- RP2, 100 kΩ
- Channel 2 plate load, 100 kΩ.
- RK1, 820 Ω
- Cathode resistor shared by both triodes. Each one is biased as if it had about 1.6 kΩ of its own. The drawing shows 1.7 V here.
- CK1, 320 µF electrolytic
- Cathode bypass cap, 320 µF. Both stages have full gain down through the bass.
- C1B, 22 nF
- Channel 2 coupling cap to the volume.
- Volume 2, 1 MΩ pot, audio taper
- Channel 2 volume, 1 MΩ.
- CBR, 5 nF
- Bright cap across the top of Volume 2, on the Lead only. It lifts the treble most with the volume low, and does nothing at full.
- Tone 2, 1 MΩ pot, audio taper
- Channel 2 tone, wired as Tone 1.
- C5B, 500 pF
- From one end of Tone 2 to the volume’s wiper.
- C6B, 10 nF
- From the other end of Tone 2 to ground.
- RM2, 680 kΩ
- Channel 2 mixing resistor, 680 kΩ.
- CM2, 500 pF
- Across channel 2’s mixing resistor, on the Lead and the Bass. It passes treble around the 680 kΩ, so channel 2 is brighter.
- V2a, 12AX7 / ECC83 / 7025
- 12AX7, the driven half of the long-tail pair phase inverter. Its plate swings opposite the input and drives tube A. Its grid connects straight to the preamp’s output with no coupling cap, so the preamp sets its DC. Both grids sit at ground through the preamp’s mixing resistors and volume pots. The 8.2 k tail sets the current.
- V2b, 12AX7 / ECC83 / 7025
- The other half of the inverter. Its grid sits at the feedback point for signal, so it’s driven through the shared cathodes, and its plate swings with the input. It drives tube B.
- 1M, 1 MΩ
- Grid resistor for the other half, 1M Ω to the driven grid, so both grids sit at the same DC. There’s no bias resistor: the cathodes sit a couple of volts above the grids, and the tail sets the current.
- 8.2k, 8.2 kΩ
- The tail resistor, to ground. It’s large, so the pair shares a nearly fixed current. When one half conducts more, the other conducts less, which splits the phase. It runs straight from the cathodes, with no bias resistor above it.
- 1µ, 1 µF
- Ties the second grid to ground for signal, so that half is driven only through the shared cathodes. There’s no feedback loop in this style.
- 100k, 100 kΩ
- Plate resistor for the driven half. It’s smaller than the other so the two outputs come out about even.
- 150k, 150 kΩ
- Plate resistor for the other half.
- 47p, 47 pF
- A small cap from plate to plate. It rolls off the far top end the inverter passes on, which keeps the feedback loop steady.
- .022µ, 22 nF
- Coupling cap to tube A’s grid.
- .022µ, 22 nF
- Coupling cap to tube B’s grid.
- 2.7k, 2.7 kΩ
- Grid stopper for tube A. It keeps the tube from oscillating and softens grid current.
- 2.7k, 2.7 kΩ
- Grid stopper for tube B.
- V3, EL84 / 6BQ5
- EL84, tube A of the push-pull pair, its cathode on the shared cathode resistor, so it biases itself.
- V4, EL84 / 6BQ5
- EL84, tube B of the pair.
- 470k, 470 kΩ
- Grid leak for tube A, to ground. The bias comes from the cathode resistor. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 470k, 470 kΩ
- Grid leak for tube B.
- 125, 125 Ω
- The shared cathode resistor. Every output tube’s current runs through it and lifts the cathodes above the grids, and that’s the bias. Driven hard, the pair draws more current on average, so the cathodes climb and the tubes run colder, which softens the clipping.
- 50µ, 50 µF electrolytic
- Bypass cap across the cathode resistor, so the cathodes hold still at the signal’s frequencies. It charges and discharges slowly as the average current changes on a hard note.
- 750, 750 Ω
- Dropping resistor from B+ to the screen supply. The screens sit slightly below the plates.
- 50µ, 50 µF electrolytic
- Filter cap on the screen supply.
- 10k, 10 kΩ
- Dropping resistor from the screen supply node to the node for the inverter and the preamp, as on the Marshall 20 W drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 32µ, 32 µF electrolytic
- Filter cap at the node for the inverter and the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 8 kΩ to 16 Ω, 40 H primary, 10 mH leakage
- The output transformer, 8 kΩ plate to plate into 16 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 305 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 305 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 305 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 90 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 90 Ω
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 50µ, 50 µF electrolytic
- The reservoir cap. It feeds the output transformer’s center tap. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- Coil R, 17.4 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 16 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 512 µH
- Voice coil inductance. It makes the impedance rise through the treble. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Loss L, 928 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 28.6 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 4.26 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 4.38 Ω
- Limits what Loss L2 adds.
- Tank R, 167 Ω
- Height of the bass resonance, about 185 Ω in all at its peak. With no feedback, the voltage at the speaker rises and falls with its impedance.
- Tank L, 42.2 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 110 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
Versions
- 2022 Lead
- The 2022 Lead, from the drawing dated 30-10-69. Channel 2 has the 5 nF bright cap across its volume and 500 pF across its mixing resistor. One ECC83 (12AX7) in the preamp.
- 2019 Bass, modeled after the Marshall 2019 20 Watt Bass
- The 2019 Bass. Channel 2 has no 5 nF bright cap. The 500 pF across its mixing resistor stays. The inverter’s second grid has 0.1 µF to ground in place of 1 µF.
- 1917 P.A., modeled after the Marshall 1917 20 Watt P.A.
- The 1917 P.A. Both channels are the same, with no bright caps. The inverter’s second grid has 0.1 µF to ground in place of 1 µF.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.