Eight-stage JFET phaser with a fuzz in front, 1975 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Roland AP-7 Jet Phaser.
A transistor and op-amp fuzz with two diodes to ground, then a mixer with resonance, then eight JFET phase stages swept by a triangle LFO. The Mode switch picks the dry guitar or the fuzz, the fuzz’s bass or treble side, and a wide or narrow sweep.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for In the Jet modes the fuzz clips the note flat on two diodes, and a bass or treble filter shapes it before Jet sets how much reaches the phaser. In the Phase modes the guitar goes straight to the mixer. The mixer’s gain is about 3, and Resonance feeds some of the eighth stage’s output back into it, which makes the notches sharper and the peaks between them taller. Eight stages make four notches. The output mixes the eighth stage through 10 kΩ with the mixer through 5.6 kΩ, so the dry side is louder and the notches are shallower than an equal mix. The LFO is a triangle from an integrator and a comparator. Slow Rate sets its speed, and the Fast footswitch moves it to a fixed fast speed, gliding there over about a second through 33 kΩ and 33 µF. At the default settings it sweeps about 1.3 times a second. Slow Rate runs up to about 3.9 a second, and Fast is about 6 a second. The odd Mode positions sweep about three times wider than the even ones. The JFETs are a 2SK30A-Y typical of the data sheet, and the internal trimmer is set to suit. Real ones spread, so a real unit’s trimmer sits somewhere else. The gate board’s electronic bypass is left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- −9 V, -9 V
- The second 9 V battery, its plus end on ground, so this rail sits at −9 V.
- C101, 47 nF
- Input coupling cap on the gate board.
- R101, 47 kΩ
- From the input to ground. It sets most of the input impedance, about 40 kΩ.
- R102, 10 kΩ
- Series resistor into Q101’s base.
- R103, 330 kΩ
- Biases Q101’s base from the −9 V side, about −1.3 V.
- R104, 10 kΩ
- Feeds Q101’s collector from −9 V.
- C102, 47 µF electrolytic
- Filters the collector’s supply.
- Q101, 2SA1015-GR
- The input buffer, a PNP emitter follower on the −9 V side. 2SA640 on the drawing.
- R105, 10 kΩ
- Q101’s emitter load.
- C103, 1 µF electrolytic
- Couples the buffer to the main board.
- R106, 100 kΩ
- Holds the main board’s input at 0 V.
- R1, 15 kΩ
- Series resistor into the fuzz.
- C1, 22 nF
- Coupling cap into Q1.
- R2, 220 kΩ
- From Q1’s base to ground.
- R3, 470 kΩ
- Half of Q1’s bias feed from its collector.
- R4, 470 kΩ
- The other half of the bias feed.
- C2, 10 µF electrolytic
- Grounds the middle of the bias feed for the signal, so the feed sets Q1’s bias without cutting its gain.
- Q1, 2SC1815
- The fuzz’s first stage, emitter grounded. 2SC1000GR on the drawing.
- R5, 15 kΩ
- Q1’s collector load.
- R6, 1 kΩ
- Feeds Q1 from +9 V.
- C3, 47 µF electrolytic
- Filters Q1’s supply.
- C4, 10 nF
- Couples Q1 into IC3a. With R7 and R8 it trims the bass below about 800 Hz.
- R7, 10 kΩ
- Series resistor into IC3a’s plus input.
- R8, 10 kΩ
- Holds IC3a’s plus input at 0 V.
- IC3a, LM2902
- A quarter of an LM2902, the fuzz’s gain stage. Its gain is 1 + 2.2 MΩ / 10 kΩ, about 220, from DC up to about 150 Hz, then C5 brings it down.
- R9, 10 kΩ
- From the minus input to ground. With R10 it sets the gain at about 220.
- R10, 2.2 MΩ
- Feedback.
- C5, 470 pF
- Across the feedback resistor. It brings the gain down above about 150 Hz, so the top end is smoother than the gain suggests.
- R11, 10 kΩ
- Series resistor into the diodes.
- C6, 47 nF
- Couples IC3a to the diodes.
- D1, D2, 1N914 / 1N4148, one each way
- Two 1S1555 diodes to ground, one each way. They square the note off near 0.6 V.
- R12, 33 kΩ
- The bass side’s resistor.
- C7, 10 nF
- With R12, a low-pass near 480 Hz. Mode positions Jet 1 and Jet 2 take the fuzz from here.
- C8, 2.2 nF
- The treble side’s cap.
- R13, 33 kΩ
- With C8, a high-pass near 2.2 kHz. Mode positions Jet 3 and Jet 4 take the fuzz from here.
- R14, 100 kΩ
- Between the two sides, so each lets some of the other through.
- Jet, 100 kΩ pot, audio taper
- Jet, VR1, 100 kΩ audio: how much fuzz reaches the mixer in the Jet modes. In the Phase modes it does nothing.
- R15, 1 kΩ
- Under Jet, so a little fuzz is left at 0.
- C9, 22 nF
- Couples the Mode switch’s first wafer into the mixer.
- R16, 220 kΩ
- Holds the switch side of C9 at 0 V, so the switch doesn’t click.
- R17, 100 kΩ
- Into the mixer’s plus input. Against R20 and R21 the signal drops to about a sixth here.
- IC3b, LM2902
- A quarter of an LM2902, the mixer. It adds the input and the resonance at a gain of about 3 and drives the eight stages and the dry side of the output.
- R18, 56 kΩ
- Feedback.
- C10, 100 pF
- Rolls off the mixer above about 28 kHz.
- R19, 27 kΩ
- From the minus input to ground. With R18 it sets the gain at about 3.
- R20, 10 kΩ
- Brings the resonance into the mixer’s plus input.
- R21, 10 kΩ
- With R22, it divides the resonance down to about a tenth.
- C11, 250 pF
- Trims the resonance’s top end above about 60 kHz, against the 10 kΩ.
- R22, 100 kΩ
- From Resonance’s wiper. A hand correction on the drawing.
- Resonance, 10 kΩ pot, linear taper
- Resonance, VR2, 10 kΩ linear: how much of the eighth stage’s output goes back into the mixer.
- C12, 10 µF electrolytic
- Blocks the diode’s DC from Resonance.
- R23, 56 kΩ
- Pulls about 0.15 mA through D3 to −9 V, so the diode conducts and passes the signal. A swing larger than that current allows is cut off, which keeps the resonance from running away.
- D3, 1N914 / 1N4148
- A 1S1555 in the resonance path, held conducting by R23.
- R30, 100 kΩ
- Into the minus input. With the feedback resistor it makes the inverting half of the stage.
- R31, 100 kΩ
- Feedback, equal to the input resistor, so every frequency comes out at the same level and only the phase moves.
- C22, 10 nF
- Feeds the plus input. Against the JFET and the 100 kΩ beside it, it sets where this stage turns the phase 90°. With the JFET pinched off, that is about 160 Hz.
- R32, 100 kΩ
- From the plus input to ground, beside the JFET. With the JFET pinched off it is the only path, and the stage turns 90° at its lowest.
- Q4, 2SK30A-Y
- A 2SK30A-Y used as a resistor that the LFO varies, from the plus input to ground. The closer its gate comes to 0 V, the lower its resistance and the higher this stage’s 90° point. The factory picked these JFETs to match.
- R33, 330 kΩ
- With C23 and the 470 kΩ, it puts about 0.6 of the stage’s own signal on the gate. The JFET then behaves more like a plain resistor on larger signals.
- C23, 10 nF
- Blocks DC, so the gate’s bias comes only from the bias line.
- R34, 470 kΩ
- From the bias line to the gate. The LFO’s sweep reaches all eight gates this way.
- IC1A, LM2902
- A quarter of an LM2902, the first of eight phase-shift stages. Half the signal goes straight, half through the filter, and the two meet here.
- R35, 100 kΩ
- Into the minus input, as in the first stage.
- R36, 100 kΩ
- Feedback, equal to the input resistor.
- C24, 10 nF
- Feeds the plus input, as in the first stage.
- R37, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q5, 2SK30A-Y
- This stage’s JFET, on the same bias line as the others.
- R38, 330 kΩ
- Feeds part of the stage’s signal to the gate, as in the first stage.
- C25, 10 nF
- Blocks DC between the plus input and the gate.
- R39, 470 kΩ
- From the bias line to this gate.
- IC1B, LM2902
- A quarter of an LM2902, phase-shift stage 2.
- R40, 100 kΩ
- Into the minus input, as in the first stage.
- R41, 100 kΩ
- Feedback, equal to the input resistor.
- C26, 10 nF
- Feeds the plus input, as in the first stage.
- R42, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q6, 2SK30A-Y
- This stage’s JFET, on the same bias line as the others.
- R43, 330 kΩ
- Feeds part of the stage’s signal to the gate, as in the first stage.
- C27, 10 nF
- Blocks DC between the plus input and the gate.
- R44, 470 kΩ
- From the bias line to this gate.
- IC1C, LM2902
- A quarter of an LM2902, phase-shift stage 3.
- R45, 100 kΩ
- Into the minus input, as in the first stage.
- R46, 100 kΩ
- Feedback, equal to the input resistor.
- C28, 10 nF
- Feeds the plus input, as in the first stage.
- R47, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q7, 2SK30A-Y
- This stage’s JFET, on the same bias line as the others.
- R48, 330 kΩ
- Feeds part of the stage’s signal to the gate, as in the first stage.
- C29, 10 nF
- Blocks DC between the plus input and the gate.
- R49, 470 kΩ
- From the bias line to this gate.
- IC1D, LM2902
- A quarter of an LM2902, phase-shift stage 4.
- R50, 100 kΩ
- Into the minus input, as in the first stage.
- R51, 100 kΩ
- Feedback, equal to the input resistor.
- C30, 10 nF
- Feeds the plus input, as in the first stage.
- R52, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q8, 2SK30A-Y
- This stage’s JFET, on the same bias line as the others.
- R53, 330 kΩ
- Feeds part of the stage’s signal to the gate, as in the first stage.
- C31, 10 nF
- Blocks DC between the plus input and the gate.
- R54, 470 kΩ
- From the bias line to this gate.
- IC2A, LM2902
- A quarter of an LM2902, phase-shift stage 5.
- R55, 100 kΩ
- Into the minus input, as in the first stage.
- R56, 100 kΩ
- Feedback, equal to the input resistor.
- C32, 10 nF
- Feeds the plus input, as in the first stage.
- R57, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q9, 2SK30A-Y
- This stage’s JFET, on the same bias line as the others.
- R58, 330 kΩ
- Feeds part of the stage’s signal to the gate, as in the first stage.
- C33, 10 nF
- Blocks DC between the plus input and the gate.
- R59, 470 kΩ
- From the bias line to this gate.
- IC2B, LM2902
- A quarter of an LM2902, phase-shift stage 6.
- R60, 100 kΩ
- Into the minus input, as in the first stage.
- R61, 100 kΩ
- Feedback, equal to the input resistor.
- C34, 10 nF
- Feeds the plus input, as in the first stage.
- R62, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q10, 2SK30A-Y
- This stage’s JFET, on the same bias line as the others.
- R63, 330 kΩ
- Feeds part of the stage’s signal to the gate, as in the first stage.
- C35, 10 nF
- Blocks DC between the plus input and the gate.
- R64, 470 kΩ
- From the bias line to this gate.
- IC2C, LM2902
- A quarter of an LM2902, phase-shift stage 7.
- R65, 100 kΩ
- Into the minus input, as in the first stage.
- R66, 330 kΩ
- Feedback, 330 kΩ on this last stage, as the drawing shows. Low notes come out of this stage about 3.3 times louder, inverted, and high notes at the level they went in, so the resonance loop has more gain in the bass.
- C36, 10 nF
- Feeds the plus input, as in the first stage.
- R67, 100 kΩ
- From the plus input to ground, beside this stage’s JFET.
- Q11, 2SK30A-Y
- This stage’s JFET, on the same bias line as the others.
- R68, 330 kΩ
- Feeds part of the stage’s signal to the gate, as in the first stage.
- C37, 10 nF
- Blocks DC between the plus input and the gate.
- R69, 470 kΩ
- From the bias line to this gate.
- IC2D, LM2902
- A quarter of an LM2902, the eighth phase-shift stage. Its output is the wet signal and feeds Resonance.
- R24, 10 kΩ
- The wet signal into the output mix.
- R25, 5.6 kΩ
- The dry signal into the output mix. It is smaller than R24, so the dry side is louder and the notches are not full cancellations. A hand correction on the drawing.
- C13, 1 µF
- Output coupling cap.
- R26, 100 kΩ
- Output pulldown.
- R109, 47 kΩ
- The gate board’s resistor at its input, to ground.
- R70, 5.6 kΩ
- From +9 V to node 8.
- R71, 5.6 kΩ
- From node 8 to the top of Slow Rate.
- Slow Rate, 10 kΩ pot, linear taper
- Slow Rate, VR3, 10 kΩ linear. Its wiper sets the voltage that sets the speed, from about 0.7 V to 4.6 V.
- R72, 1.8 kΩ
- Under Slow Rate, so the slowest speed is not a stop.
- R73, 33 kΩ
- With C14, makes the speed glide when the footswitch is pressed.
- C14, 33 µF electrolytic
- 33 µF. With R73 it takes about a second for the speed to move after the footswitch is pressed.
- Q2, 2SC1815
- An emitter follower. It drives the integrator from the speed voltage. 2SC373 on the drawing.
- R74, 82 kΩ
- From Q2’s emitter toward the integrator’s minus input.
- R75, 100 kΩ
- Into the integrator’s minus input.
- R76, 18 kΩ
- With R77, holds the integrator’s plus input at about 0.36 of Q2’s emitter.
- R77, 10 kΩ
- The lower half of that divider. With Q3 on or off, the current into the cap is the same size each way, so the triangle’s two slopes match.
- C15, 220 nF
- The integrator’s cap. The current into it sets how fast the triangle ramps.
- IC3d, LM2902
- A quarter of an LM2902, the integrator. Its output is the triangle.
- Q3, 2SK30A-Y
- A 2SK30A-Y used as a switch. On, it grounds the join of R74 and R75, so the current into the cap flows the other way and the triangle turns round.
- R78, 100 kΩ
- Holds Q3’s gate at 0 V, so it is on, while D4 is off.
- D4, 1N914 / 1N4148
- A 1S1555. With the comparator low, it pulls Q3’s gate down to about −8 V and turns it off.
- IC3c, LM2902
- A quarter of an LM2902, the comparator. It flips each time the triangle reaches half its own output, so the triangle runs between about −4.5 V and +3.8 V.
- R79, 10 kΩ
- Positive feedback from the output, half of it.
- R80, 10 kΩ
- The other half of the comparator’s divider.
- R81, 56 kΩ
- The wide sweep’s resistor (odd Mode positions).
- R82, 220 kΩ
- The narrow sweep’s resistor (even Mode positions).
- R83, 12 kΩ
- Divides the triangle down, to about a sixth through R61 or a twentieth through R62. A hand correction on the drawing.
- R84, 470 kΩ
- Carries the sweep to the bias line.
- R85, 10 kΩ
- From −9 V to the zener.
- ZD, 5.6 V zener, in breakdown
- A 5.6 V zener (05Z5.6A). It holds the bias chain at −5.6 V as the battery runs down.
- R86, 100 kΩ
- The top of the trimmer’s chain.
- VR4, 50 kΩ pot, linear taper
- The internal trimmer, VR4, 50 kΩ linear. It sets the JFET gates’ voltage, from about −0.7 V to −2.3 V, which places the sweep. On the bench it is set for this file’s JFET.
- R87, 22 kΩ
- The bottom of the trimmer’s chain.
- R88, 100 kΩ
- From the trimmer to the bias line.
- C16, 1 µF
- Smooths the bias line. With about 100 kΩ feeding it, it rounds the triangle’s corners and cuts the sweep at the fast speed.
About this version
- Factory values
- Two 9 V batteries, ±9 V. The 2SC1815 stands in for the 2SC1000GR (Q1) and the 2SC373 (Q2), the 2SA1015 for the 2SA640 (Q101), the 1N914 for the 1S1555.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.