OTA band-pass filter with envelope and sample-and-hold control, 1976 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Maestro FSH-1 Filter Sample/Hold.
Two 3080s make a resonant band-pass filter. In Filter mode the guitar’s own envelope sweeps it up on each pick. In Sample/Hold mode a clock grabs a random voltage from a noisy transistor several times a second, so the filter jumps to a new place on every tick.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for Q1 buffers the guitar. R4 and R5 cut it about 30 times before IC1, so the 3080s see only millivolts and stay clean. IC1 and IC2 each charge a cap, C3 and C5, and the two are wired in a loop. That loop is a state-variable filter, and the output is its band-pass, at Q2’s source. R7 sets how sharp the peak is. The peak is about 20 dB over the guitar and narrow, with a Q near 10. The current into the 3080s’ bias pins sets the peak’s frequency. It is about 340 Hz at the 3.5 µA each pin gets at rest, 1 kHz at 10 µA, 2.5 kHz at 27 µA and 6 kHz at 68 µA. Q3 turns the control voltage into that current. Only a voltage over the 0.5 V on its emitter pushes current in. In Filter mode the control is the guitar’s envelope. IC3 rectifies the guitar with a gain of about 45 into C6, which charges in about 15 ms and drains through R19 in about half a second. With Filter Range at full, a 0.2 V pick moves the peak from 340 Hz to about 2.5 kHz and back. Lower settings sweep less. In Sample/Hold the control is random. Q4’s junction in breakdown is noisy, and IC4 amplifies that noise to about 0.6 V rms. The clock, IC5, lifts Q5’s gate for under a millisecond, 2.6 to 13 times a second as S/H Speed turns up, and C9 holds the noise’s value until the next tick. With the trims as set, the peak jumps between about 340 Hz and 2.3 kHz, centered near 1.4 kHz. A real unit’s noise level depends on the transistor picked for Q4.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- −9 V, -9 V
- The −9 V supply, a steady source here.
- R35, 470 Ω
- With C12 it filters the +9 V into the +8 V line for the filter, Q1 and Q2.
- C11, 220 µF
- Filter cap on the +9 V rail.
- C12, 220 µF
- Filter cap on the +8 V line.
- R36, 470 Ω
- With C14 it filters the −9 V into the −8 V line.
- C13, 220 µF
- Filter cap on the −9 V rail.
- C14, 220 µF
- Filter cap on the −8 V line.
- C1, 47 nF
- Input coupling cap. With R2 it passes everything above about 34 Hz.
- R2, 100 kΩ
- Sets the input impedance, about 100 kΩ.
- R1, 10 kΩ
- Base stopper for Q1.
- Q1, MPS5172
- Emitter follower (MPS5172). It drives the filter, the envelope and the bypass from a low impedance.
- R3, 22 kΩ
- Q1’s emitter load to −8 V, about 0.33 mA.
- C2, 150 nF
- Coupling cap from Q1 to the filter, Filter Range and the bypass.
- R4, 100 kΩ
- With R5 it cuts the guitar about 30 times (−30 dB) before IC1, so the 3080 sees only millivolts and stays clean.
- R5, 3.3 kΩ
- The bottom of IC1’s input divider.
- R7, 1 MΩ
- Damping. It feeds the band-pass back into IC1’s − input. Its ratio to R4 sets the filter’s peak gain, about 10 (20 dB), and the sharpness of the peak.
- IC1, CA3080
- The first integrator, a 3080. Its output current charges C3. The current into its bias pin sets its gain, and so the filter’s frequency.
- C3, 1 nF
- IC1’s integrating cap.
- Q2, 2N4303
- JFET source follower (2N4303). It reads C3 without loading it. Its source is the band-pass output.
- R8, 12 kΩ
- Q2’s source load to −8 V.
- R9, 100 kΩ
- With R10 it cuts the band-pass about 30 times before IC2.
- R10, 3.3 kΩ
- The bottom of IC2’s input divider.
- IC2, CA3080
- The second integrator, a 3080 on the same control current as IC1. Its output on C5 is the low-pass, fed back to IC1’s + input.
- R12, 3.3 kΩ
- Ground for IC2’s + input, the same resistance its − input sees.
- C5, 30 nF
- IC2’s integrating cap.
- R6, 22 kΩ
- Shares Q3’s current into IC1’s bias pin.
- R13, 22 kΩ
- Shares Q3’s current into IC2’s bias pin.
- R20, 2.7 MΩ
- A small current from ground into the bias pins, about 3 µA, so the filter never shuts off with Q3 off.
- C7, 150 nF
- Smooths the bias current, so the filter glides slightly between steps.
- Q3, 2N3906
- Common-base PNP (2N3906). The current into its emitter comes out its collector into the 3080s’ bias pins.
- R21, 1 MΩ
- A small steady current, about 8 µA, into Q3’s emitter.
- R22, 22 kΩ
- Turns the control voltage into a current. Q3’s emitter sits about 0.5 V over ground, so only a control voltage over that pushes current in.
- R23, 100 kΩ
- In Sample/Hold it adds the offset trim’s current to Q3’s emitter.
- R26, 100 kΩ pot, linear taper
- Offset trim, 100 kΩ from +9 to −9 V. In Sample/Hold it pulls current back out of Q3’s emitter, so it sets the middle of the jumps. Set at 0.08 here (about −7.6 V), so the jumps center near 1.4 kHz.
- R11, 3.3 kΩ
- Output resistor from the band-pass.
- C4, 150 nF
- Output coupling cap.
- R14, 100 kΩ
- Holds the output at 0 V DC.
- Filter Range, 100 kΩ pot, audio taper
- Filter Range, 100 kΩ. It sets how much of the guitar reaches the envelope follower, so how far each pick sweeps the filter in Filter mode. The taper isn’t marked, so it is set as audio taper.
- R16, 22 kΩ
- IC3’s input resistor.
- IC3, LM741 / µA741
- Precision half-wave rectifier, a 741. On the negative half of the guitar its output rises and D3 passes it, with a gain of R17 over R16, about 45.
- D2, 1N914 / 1N4148
- On the positive half it holds IC3’s output a diode drop under its − input, so the output never swings to the rail.
- D3, 1N914 / 1N4148
- Passes only the rectifier’s positive output.
- R17, 1 MΩ
- IC3’s feedback, through D3. With R16 it sets the gain, about 45.
- R18, 3.3 kΩ
- With C6 it sets the attack, about 15 ms.
- C6, 4.7 µF
- The envelope’s hold cap, 4.7 µF, its other end on +9 V.
- R19, 100 kΩ
- With C6 it sets the decay, about 0.5 s.
- R24, 100 kΩ
- Feeds Q4’s junction about 0.1 mA from +9 V.
- Q4, 2N3904 emitter-base, in breakdown
- The noise source, a 2N3904 with its base open. Its emitter-base junction breaks down in reverse at about 7.5 V, and in breakdown the current through it is noisy. The noise is set at 15 nA per root hertz, about 20 µV per root hertz across the junction, an assumed figure for a junction picked for noise.
- C8, 47 nF
- Passes the noise to IC4 and blocks Q4’s DC.
- IC4, LM741 / µA741
- Noise amplifier, a 741. The noise current into its − input comes out as a voltage, R25 times that current.
- R25, 1 MΩ
- IC4’s feedback, 1 MΩ.
- R27, 10 kΩ pot, linear taper
- Noise level trim, 10 kΩ. It sets how big the random steps are. Set at 0.8 here.
- Q5, 2N4303
- The sample switch (2N4303). With its gate pulled to −9 V it is off. On each short clock pulse R30 lifts its gate and it connects the noise to C9.
- R30, 1 MΩ
- Gate resistor from the clock. When the clock is high, Q5’s gate rises to its channel through R30 without loading the clock.
- C9, 47 nF
- The hold cap. It keeps the last sample until the next pulse.
- Q6, 2N4303
- JFET source follower (2N4303). It reads C9 without draining it.
- R31, 22 kΩ
- Q6’s source load to −9 V.
- IC5, LM741 / µA741
- The clock, a 741 Schmitt oscillator. Its output is high for under a millisecond and low for the rest of each period.
- C10, 150 nF
- The clock’s timing cap.
- S/H Speed, 2 MΩ pot, linear taper
- S/H Speed, a 2 MΩ rheostat in series with R29. Less resistance discharges C10 faster, so the clock ticks faster. The taper isn’t marked, so it is set as linear.
- R29, 330 kΩ
- The slowest part of the clock’s period, with S/H Speed at its fastest.
- R32, 3.3 kΩ
- With D1 it charges C10 fast while the clock is high, so the sample pulse is short.
- D1, 1N914 / 1N4148
- Conducts only while the clock is high.
- R33, 22 kΩ
- Positive feedback. With R34 it sets the switching points at about two thirds of the output swing.
- R34, 47 kΩ
- The bottom of the clock’s switching divider.
About this version
- Drawn
- On ±9 V from two steady sources, with 470 Ω and 220 µF filters to the ±8 V lines for the filter. The trims are set as a builder would set them.
Sources
- JD Sleep, redrawn schematic
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.