Envelope filter with a transistor tuning a bridged T, 1976 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Electro-Harmonix Doctor Q.
An auto-wah on one dual op-amp and one transistor. The guitar’s level, rectified, sets the transistor’s base current, and the transistor works as a resistor that tunes a peak in the filter. Sensitivity sets how far a pick moves the peak.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for U1B is the filter. With Q1 off, the response is flat up to about 200 Hz and falls above it, with a rise of about 4 dB there. Q1 sits between the middle of the bridged T and ground with no DC across it, so it works as a resistor set by its base current. As that resistance falls, the peak moves up and gets taller, to about 1.8 kHz and 18 dB with 0.56 V on the base. U1A amplifies the guitar about 47 times. Its plus input is on ground, so only the guitar’s negative halves swing its output up. D1 charges C5 on those peaks, and C5 drains through D2, the Range trim and Q1’s base, so the peak falls back as the note dies. With the knobs at their default settings, a 200 mV pick moves the peak to about 800 Hz. The bench’s MC1458 model rests 1.8 V over ground on a 9 V supply, and the guitar never swings it out of that, so an LM358 model stands in for the envelope half. How low the original chip rests isn’t known. In Bass, the response at rest has a 13 dB peak near 200 Hz in place of the 4 dB one.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R10, 47 kΩ
- Top of the Vbias divider.
- R11, 47 kΩ
- Bottom of the Vbias divider. With R10 it sets Vbias at 4.5 V.
- C6, 10 µF electrolytic
- Filters Vbias.
- R2, 47 kΩ
- Loads the filter’s input to ground. In Bass it is all that holds the open input.
- C1, 10 nF
- Input coupling cap into the filter.
- R3, 470 kΩ
- The filter’s input resistor. With R4 it sets the gain away from the peak at about 1.
- U1B, MC1458
- Half of the dual op-amp, the filter. An MC1458 stands in for the ECG778.
- R4, 470 kΩ
- The filter’s feedback resistor.
- C8, 1 nF
- From the minus input to ground.
- C3, 5 nF
- One of the bridged T’s two caps, from the minus input to the middle.
- C2, 5 nF
- The bridged T’s other cap, from the middle to the output.
- Q1, BC239C
- BC239C. Its collector sits at 0 V, so it works as a resistor from the T’s middle to ground, lower with more base current. Lower resistance moves the peak up.
- R5, 47 kΩ
- From the T’s middle to ground in Norm, to the input jack in Bass. With Q1 off it sets the bottom of the sweep.
- Sensitivity, 100 kΩ pot, linear taper
- Sensitivity, 100 kΩ, across the input. It sets how much of the guitar reaches the envelope amp. The taper is not marked. Linear is assumed.
- R7, 47 kΩ
- The envelope amp’s input resistor. With R8 it sets the gain at about 47.
- C4, 50 nF
- Coupling cap into the envelope amp.
- U1A, LM358
- The other half, the envelope amp. Its plus input is on ground, so it rests at its low limit and only the guitar’s negative halves swing it up. An LM358 model stands in here, since the bench’s MC1458 model rests too far over ground for the guitar to move it.
- R8, 2.2 MΩ
- The envelope amp’s feedback resistor.
- D1, 1N914 / 1N4148
- Charges C5 on the envelope amp’s peaks.
- R9, 100 Ω
- Limits the charging current into C5.
- C5, 10 µF electrolytic
- The envelope cap. It charges on each pick and drains through D2, the Range trim and Q1’s base.
- D2, 1N914 / 1N4148
- From the envelope cap to the Range trim. Its drop, with Q1’s base, sets how high C5 must charge before Q1 conducts.
- Range, 25 kΩ pot, linear taper
- The Range trim, 25 kΩ, to ground. Its wiper feeds Q1’s base through R6, so it sets how much of the envelope reaches the transistor, and how high the peak goes. Set at full (assumed). Lower, a medium pick barely moves the peak.
- R6, 22 kΩ
- Into Q1’s base. It sets the base current from the trim’s wiper.
- C7, 50 nF
- Output coupling cap.
- R12, 470 kΩ
- Holds the output at 0 V DC.
About this version
- Stock
- Negative ground, 9 V. An MC1458 stands in for the ECG778 dual op-amp. BC239C tuning transistor.
Sources
- Jack Orman (muzique.com), traced schematic
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.