Four-stage JFET phaser, 1976 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Univox Micro Fazer.
Four op-amp stages, each set by a JFET, turn the guitar’s phase. The wet signal meets the guitar straight from the input jack, and the two cancel at two notches. A slow oscillator moves the JFET gates, and the notches sweep. One knob, Rate.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for R1 and R2 halve the guitar, and OP1 raises it 1.21 times into four all-pass stages. Each one passes every pitch at the same level and turns its phase, 90° at 1 / (2π R C), where R is the stage’s JFET beside its 100 kΩ and C is 50 nF. OP5 also raises the wet signal 3.2 times. The dry signal goes straight from the input jack through R20, and the two meet at the output through equal 22 kΩ resistors. Where the wet signal has turned 180° and 540° the two cancel, so four stages make two notches. The wet signal comes out about twice the dry, so the notches are about 10 dB deep. With the gates at the middle of their swing the notches sit at about 280 Hz and 1.6 kHz. The LFO swings the gates about 0.3 V, from pinch-off, where the lower notch drops under 100 Hz, to about 1 kHz. Rate runs from one sweep every 3.3 seconds to about 11 a second. R20 and R22 load the guitar with about 70 kΩ, Enable on or off. The JFETs are a 2SK30A typical of its data sheet, with the trimmer set to suit, so a real pedal’s sweep may sit elsewhere.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- R23, 2.7 kΩ
- From the battery to the zener. About 1.6 mA flows through it.
- D1, 4.7 V zener, in breakdown
- A 4.7 V zener. It holds the zener line steady as the battery runs down, and every stage and the JFETs’ sources sit on it.
- C7, 33 µF electrolytic
- The zener line’s filter cap. It makes the line a quiet AC ground for the stages.
- R1, 220 kΩ
- Into the effect. With R2 it halves the guitar before OP1.
- C1, 50 nF
- Input coupling cap.
- R2, 220 kΩ
- Biases OP1 at the zener line. With R1 it halves the signal.
- OP1, MC1458
- Half a 1458, the input buffer. Its gain is 1.21.
- R4, 100 kΩ
- OP1’s feedback.
- R3, 470 kΩ
- From OP1’s minus input to the zener line. With R4 the gain is 1 + 100 k / 470 k = 1.21.
- R5, 100 kΩ
- Into the minus input. With the 100 kΩ feedback resistor it makes the inverting half of the stage, a gain of one, inverted.
- R7, 100 kΩ
- Feedback, equal to the input resistor, so every pitch comes out at the same level and only the phase moves.
- C2, 50 nF
- Feeds the plus input. Against the 100 kΩ and the JFET beside it, it sets where this stage turns the phase 90°, about 32 Hz with the JFET pinched off.
- R6, 100 kΩ
- From the plus input to the zener line, beside the JFET.
- Q1, 2SK30A-GR
- A JFET used as a resistor that the LFO varies. The drawing marks a 2SK34D, “selected”, and lists the 2SK30A as an equivalent, which stands in here. The closer its gate comes to its source, the lower its resistance and the higher this stage’s 90° point.
- OP2, MC1458
- Half a 1458, the first of four phase-shift stages.
- R8, 100 kΩ
- Into the minus input, as in the first stage.
- R10, 100 kΩ
- Feedback, equal to the input resistor.
- C3, 50 nF
- Feeds the plus input, 50 nF as in every stage.
- R9, 100 kΩ
- Beside this stage’s JFET, 100 kΩ.
- Q2, 2SK30A-GR
- This stage’s JFET, on the same gate line.
- OP3, MC1458
- Half a 1458, phase-shift stage 2.
- R11, 100 kΩ
- Into the minus input, as in the first stage.
- R13, 100 kΩ
- Feedback, equal to the input resistor.
- C4, 50 nF
- Feeds the plus input, 50 nF as in every stage.
- R12, 100 kΩ
- Beside this stage’s JFET, 100 kΩ.
- Q3, 2SK30A-GR
- This stage’s JFET, on the same gate line.
- OP4, MC1458
- Half a 1458, phase-shift stage 3.
- R14, 100 kΩ
- Into the minus input, as in the first stage.
- R16, 100 kΩ
- Feedback, taken from the R17 / R18 divider in place of the output, so this stage’s gain is 3.2 at every pitch.
- C5, 50 nF
- Feeds the plus input, 50 nF as in every stage.
- R15, 100 kΩ
- Beside this stage’s JFET, 100 kΩ.
- Q4, 2SK30A-GR
- This stage’s JFET, on the same gate line.
- OP5, MC1458
- Half a 1458, the fourth stage. Its output is the wet signal, 3.2 times larger.
- R17, 2.2 kΩ
- With R18, divides OP5’s output for its feedback, so the stage runs at a gain of 3.2.
- R18, 1 kΩ
- The bottom of OP5’s feedback divider.
- C6, 1 µF electrolytic
- Couples the wet signal to the mix.
- R19, 100 kΩ
- Holds C6’s far end at ground.
- R21, 22 kΩ
- The wet signal into the mix.
- R20, 22 kΩ
- The dry signal, straight from the input jack to the output, equal to R21. It’s also the whole path with Enable off.
- R22, 47 kΩ
- From the output to ground. With R20 it loads the guitar with about 70 kΩ, so the pickup’s highs drop slightly even with Enable off.
- Bias, 100 kΩ pot, linear taper
- The internal Bias trimmer, 100 kΩ from the zener line to ground. It sets how far below their sources the JFET gates sit. Set at 0.72 for this file’s JFET, an assumed setting.
- R30, 470 kΩ
- The bias into the gate line.
- C8, 10 µF electrolytic
- Couples the LFO’s ramp onto the gate line, so the trimmer alone sets the gates’ DC.
- R31, 1 MΩ
- With R30, lets about a third of the ramp reach the gates.
- OP6, MC1458
- Half a 1458, the LFO. Its output is a square wave, high or low.
- R26, 47 kΩ
- From the zener line to the plus input. With R28 it sets the two switch points either side of 4.7 V.
- R28, 220 kΩ
- Positive feedback from the output. It snaps the op-amp to one side and holds it there until the cap reaches the switch point.
- R29, 27 kΩ
- In series with Rate. It sets the top speed.
- Rate, 1 MΩ pot, reverse audio taper
- Rate, 1 MΩ, a variable resistor from R29 to the timing cap. At 0 all of it is in the path, the slowest setting, and at full none of it is. The drawing marks it log. It’s modeled as reverse audio, an assumption, so the speed spreads evenly over the turn.
- C9, 4.7 µF electrolytic
- The timing cap, a tantalum. It ramps up and down between the switch points, and that ramp is the sweep.
About this version
- Stock
- The circuit as redrawn from the original schematic. 1458 op-amps, 2SK30A JFETs in place of the 2SK34D.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.