Master-volume 50 W tube amp, 1976 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Marshall 2204 50 W master volume (1976).
Two inputs, each with its own triode, mixed at the Volume. Then one more gain stage, a cathode follower into the treble-mid-bass tone stack, and a Master ahead of the phase inverter.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for High goes into V1b, which has a small bypass cap and a .002 µF coupling cap, so it amplifies the mids and treble most. Low goes into V1a, with a big bypass cap and .02 µF, so it passes the bass. Each one meets the Volume through 100 kΩ. V2a, with a 330 kΩ plate resistor and no bypass cap, is the stage that clips. The Master sets how hard the inverter and the two 6550s are driven, so the preamp can clip at a low level. On Preamp only, you hear the signal as it reaches the phase inverter.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- 10k, 10 kΩ
- Dropping resistor, 10 kΩ 1 W, from the inverter’s node to V2’s node.
- 50µ, 50 µF electrolytic
- Filter cap on V2’s node.
- 10k, 10 kΩ
- Dropping resistor, 10 kΩ 1 W, to V1’s node.
- 50µ, 50 µF electrolytic
- Filter cap on V1’s node.
- 1M, 1 MΩ
- The High input’s 1 MΩ to ground, the load the guitar sees.
- 68k, 68 kΩ
- Grid stopper into V1b. With the tube’s input capacitance it keeps radio out.
- V1b, 12AX7 / ECC83 / 7025
- The High input’s stage. With its small bypass cap it has full gain only above a couple of hundred hertz.
- 100k, 100 kΩ
- V1b’s plate resistor. The drawing shows 205 V on the plate.
- 2700, 2.7 kΩ
- V1b’s cathode resistor, a cool bias. The drawing shows 2 V here.
- .68µ, 680 nF
- V1b’s bypass cap. Against 2.7 kΩ it bypasses only above about 90 Hz, and fully from a few hundred hertz up.
- .002µ, 2 nF
- V1b’s coupling cap, only 2 nF. Into the 100 kΩ and the Volume it thins the bass.
- 100k, 100 kΩ
- From V1b’s coupling cap to the top of the Volume. With the other input’s 100 kΩ it mixes the two stages.
- 1M, 1 MΩ
- The Low input’s 1 MΩ to ground.
- 68k, 68 kΩ
- Grid stopper into V1a.
- V1a, 12AX7 / ECC83 / 7025
- The Low input’s stage, bypassed all the way down. With no guitar in Low, its grid is grounded by the jack’s switch, but it still loads the Volume’s top through its 100 kΩ.
- 100k, 100 kΩ
- V1a’s plate resistor. The drawing shows 150 V on the plate.
- 820, 820 Ω
- V1a’s cathode resistor, a warmer bias. The drawing shows 1.1 V here.
- 330µ, 330 µF electrolytic
- V1a’s bypass cap, 330 µF. Full gain through the bass.
- .02µ, 20 nF
- V1a’s coupling cap.
- 100k, 100 kΩ
- From V1a’s coupling cap to the top of the Volume.
- Volume, 1 MΩ pot, audio taper
- Volume, 1 MΩ. Its wiper is V2a’s grid.
- .0005µ, 500 pF
- Bright cap, 500 pF, across the top of the Volume. It lifts the treble with the Volume down and does nothing at full.
- V2a, 12AX7 / ECC83 / 7025
- The second gain stage, with a 330 kΩ plate resistor and no bypass cap. Its plate drives the cathode follower directly.
- 330k, 330 kΩ
- V2a’s plate resistor, 330 kΩ. The plate sits low, 74 V on the drawing, so the stage runs out of room early on the upswing.
- 820, 820 Ω
- V2a’s cathode resistor, unbypassed. The drawing shows 0.6 V here.
- V2b, 12AX7 / ECC83 / 7025
- Cathode follower, DC-coupled from V2a’s plate, driving the tone stack.
- 100k, 100 kΩ
- Cathode follower load. The drawing shows 76 V on the cathode.
- .0005µ, 500 pF
- Treble cap.
- 33k, 33 kΩ
- Slope resistor.
- .022µ, 22 nF
- Bass cap.
- .022µ, 22 nF
- Mid cap.
- Treble, 250 kΩ pot, linear taper
- Treble pot, 250 kΩ. Its wiper is the tone stack’s output.
- Bass, 1 MΩ pot, audio taper
- Bass pot, a variable resistor between the treble pot’s bottom and the mid pot.
- Middle, 25 kΩ pot, linear taper
- Mid pot, 25 kΩ, with the mid cap on the wiper.
- Master, 1 MΩ pot, audio taper
- Master volume, 1 MΩ, ahead of the phase inverter. It sets how hard the inverter and the power tubes are driven.
- .022µ, 22 nF
- Coupling cap into the phase inverter’s grid.
- V3a, 12AX7 / ECC83 / 7025
- 12AX7, the driven half of the long-tail pair phase inverter. Its plate swings opposite the input and drives tube A. Its grid is fed through the preamp’s coupling cap, so there’s no second one here.
- V3b, 12AX7 / ECC83 / 7025
- The other half of the inverter. Its grid sits at the feedback point for signal, so it’s driven through the shared cathodes, and its plate swings with the input. It drives tube B.
- 1M, 1 MΩ
- Grid resistor for the driven half, returned to the bias point above the tail, not to ground.
- 1M, 1 MΩ
- Grid resistor for the other half.
- 470, 470 Ω
- Bias resistor for both halves. The cathodes sit this far above the grids’ return, a volt or so.
- 10k, 10 kΩ
- The tail resistor. It’s large, so the pair shares a nearly fixed current. When one half conducts more, the other conducts less, which splits the phase.
- .022µ, 22 nF
- Ties the second grid to the feedback point for signal, so the feedback acts across the pair.
- 82k, 82 kΩ
- Plate resistor for the driven half. It’s smaller than the other so the two outputs come out about even.
- 100k, 100 kΩ
- Plate resistor for the other half.
- 47p, 47 pF
- A small cap from plate to plate. It rolls off the far top end the inverter passes on, which keeps the feedback loop steady.
- 100k, 100 kΩ
- The feedback resistor from the speaker. With the 4.7k Ω below it, it sends about 4 % of the speaker voltage back to the inverter, which lowers the gain, flattens the response and tightens the bass.
- 4.7k, 4.7 kΩ
- The bottom of the feedback loop, 4.7k Ω to ground. The fed-back speaker voltage arrives here and moves the tail.
- .1µ, 100 nF
- The presence cap, in series with the pot across the leg. With the pot it sets where the lift starts.
- Presence, 5 kΩ pot, linear taper
- Presence, a 5k linear pot as a variable resistor, its resistance falling as it’s turned up, in series with the cap across the leg. Turned up, the cap shunts more of the leg’s treble, so less treble is fed back and the top end rises.
- .022µ, 22 nF
- Coupling cap to tube A’s grid.
- .022µ, 22 nF
- Coupling cap to tube B’s grid.
- V4, 6550
- n6550, tube A of the push-pull pair, cathode grounded, biased from the fixed bias supply.
- V5, 6550
- n6550, tube B of the pair.
- 220k, 220 kΩ
- Grid leak for tube A, returned to the bias supply. Driven into grid current, the coupling cap charges through it and the bias goes colder for a moment. That’s blocking distortion.
- 220k, 220 kΩ
- Grid leak for tube B.
- 1k, 1 kΩ
- Screen resistor for tube A. It limits the screen current when the tube is driven hard.
- 1k, 1 kΩ
- Screen resistor for tube B.
- 5 H, 5 H
- A choke from B+ to the screen supply, as in the amp this style is based on. It passes DC with little drop, so the screens sit close to B+. With the cap after it, it would filter ripple, but ripple isn’t modeled here. Typical of the part.
- 100, 100 Ω
- The choke’s winding resistance, typical. It’s all the DC drop the screens see from B+.
- 50µ, 50 µF electrolytic
- Filter cap on the screen supply.
- 10k, 10 kΩ
- Dropping resistor from the screen supply node to the node for the inverter and the preamp, as on the Marshall 2204 drawing. The current drawn past it drops the voltage, so each stage down the chain runs lower than the one before, and a hard note that pulls B+ down pulls these down too. The preamp runs off this node instead of its own HT supply.
- 50µ, 50 µF electrolytic
- Filter cap at the node for the inverter and the preamp. With the dropping resistor it filters the supply and keeps the stages on this node from coupling to each other through it.
- OT, 3.4 kΩ to 16 Ω, 40 H primary, 10 mH leakage
- The output transformer, 3.4 kΩ plate to plate into 16 Ω, center tap on B+. Tap any piece of it to change its figures. The core saturates as the flux nears its knee. Every figure is typical of the part.
- PT, 300 V ac, 60 Hz
- One half of the power transformer’s high-voltage winding, 300 V ac from the grounded center tap, as a sine source at the mains frequency. The value is typical of the part.
- PT, 300 V ac, 60 Hz
- The other half of the winding, from the grounded center tap. It runs opposite the first half, so the rectifier charges the reservoir on every half cycle.
- PT R, 50 Ω
- Resistance of one half of the winding, plus the primary’s share. With the rectifier’s own drop it sets how far B+ sags on a hard note. Typical of the part.
- PT R, 50 Ω
- Resistance of the other half. Typical of the part.
- D1, 1N4001
- One of the silicon rectifier diodes. It drops under a volt, so B+ holds up better under load than with a tube rectifier.
- D2, 1N4001
- The other rectifier diode, on the other half cycle.
- 100µ, 100 µF electrolytic
- The reservoir cap. It feeds the output transformer’s center tap. It charges in short pulses at each peak of the mains and drains between them, so B+ carries ripple, and on a hard note it sags.
- PT, 300 V ac, 60 Hz
- The end of the high-voltage winding the bias comes off, 300 V ac, the same end as the rectifier’s first plate. It’s drawn as its own source so the bias supply’s average can be found. Keep it equal to the winding beside the rectifier.
- 150k, 150 kΩ
- Series resistor into the bias rectifier, 150k Ω. There’s no bias tap, so the bias comes straight off the high-voltage winding, and this resistor drops most of it.
- Bias diode, 1N4001
- The bias rectifier, a silicon diode turned so the supply comes out negative.
- 10µ, 10 µF electrolytic
- Filter cap on the bias supply, its plus side to ground.
- 15k, 15 kΩ
- Second resistor of the bias supply, 15k Ω to the bias line. With the cap after it, it filters the ripple a second time.
- 10µ, 10 µF electrolytic
- Second filter cap, on the bias line, its plus side to ground.
- 47k, 47 kΩ
- From the bias line toward ground, 47k Ω, in series with the bias pot. These two and the 15k Ω above them divide the supply down to the bias.
- Bias 25k, 25 kΩ pot, linear taper
- Bias adjust, a 25k Ω trimmer used as a variable resistor, the bottom of the divider. More resistance puts more of the supply on the grids, so turned up the tubes idle cooler. Which way it turns isn’t marked on the drawing.
- Coil R, 17.4 Ω
- Voice coil resistance, the floor of the speaker’s impedance. The shape of a 1x12 open-back cab with an alnico 12 in, measured (a 93 Ω peak near 74 Hz on 8 Ω), scaled to the 16 Ω tap. One real cab, not every speaker. The Speaker menu by the play buttons is separate. It plays the note through a speaker and cab impulse response, with either load.
- Coil L, 512 µH
- Voice coil inductance. It makes the impedance rise through the treble. The feedback holds the output steadier against that than it would be without feedback.
- Loss L, 928 µH
- With Loss R across it, the treble rises and then levels off, like the losses in a real coil.
- Loss R, 28.6 Ω
- Limits what Loss L adds to the treble rise.
- Loss L2, 4.26 mH
- A second step in the treble rise, with Loss R2 across it: a real voice coil’s losses keep climbing from a few hundred hertz.
- Loss R2, 4.38 Ω
- Limits what Loss L2 adds.
- Tank R, 167 Ω
- Height of the bass resonance, about 185 Ω in all at its peak. The feedback holds the output steadier against that than it would be without feedback.
- Tank L, 42.2 mH
- With Tank C, sets the resonance: 74 Hz.
- Tank C, 110 µF
- With Tank L, sets the resonance. With Tank R, it sets how narrow the peak is.
About this version
- ECC83 throughout
- Two ECC83 (12AX7) twin triodes, as the drawing lists them.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.