Two-line bucket-brigade chorus, 1985 style
Pedal and tube amp circuits, simulated part by part the way an engineer’s circuit simulator does it, while you listen and watch. Turn the knobs, change any part, or tap a wire to put a probe on it.
Every part is simulated. Nothing you hear is a recording.
1Pick a circuit
Choose one from the menu, or type a name, maker or year in Find a circuit. The buttons under the menu switch between versions.
2Set the knobs and the input
Turn the circuit’s knobs on the front panel. In the Input box, choose Guitar or Signal generator, and the note or chord.
3Press Play
Press Play through the circuit to hear a picked note or chord. Play the string is the guitar by itself.
4Tap a part
Tap any part on the schematic to change its value, or swap the transistor, tube or diode. The red numbers are DC voltages, and they update as you go.
5Tap a wire
Tap a wire to put the probe there. The Probe graph and the spectrum show the signal there.
6Try a change
Press Try it on a card under Try this to hear one change, before and after. Modify this circuit, below the schematic, adds or removes parts.
Good to know
- Not sure what a control does? Hover over it, or hold a finger on it, for a short note.
- For a whole build or mod step by step, open Walkthroughs here.
- To put together a pedal or preamp of your own, use the Builder tab.
- Your switches stay where you left them the next time you open that circuit, in this browser only.
- A tube amp opens whole, with its power amp. Pick Preamp only in the Power amp menu to hear the preamp by itself, or pick another power amp to hear this preamp through it.
- The graphs use a steady test tone. Play sounds a picked note that dies away.
- Part values are typical of their type. Each circuit’s notes say which schematic it’s based on.
Modeled after the Boss DC-2 Dimension C.
Two MN3207 delay chips each hold a copy of the guitar 2 to 3 ms behind. One slow triangle swings the two delays in opposite directions, and two mixers add the copies to the dry signal for outputs A and B. The bench plays output A.
Try this
Common mods
Changes people often make to this circuit. Try it plays the note before and after, at the same loudness. Keep it adds the mod to Your changes, where it can go on a switch.
Input
Peak voltage from the pickup for each note. Strum hard and a single coil puts out a few hundred millivolts. When you play a chord, its strings share this level.
Your build
Stack blocks from the guitar down to the output. Tap + Add a block wherever you want one. The coupling caps and the supply are wired in for you.
Your blocks. These are blocks you saved with Save block, values and part changes included. Add one to any build of the same kind with + Add a block. They stay in this browser.
Your builds stay in this browser, on this device, and nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so Save to a file to keep a copy. Open a file, or drop the .bench file on the page, brings it back on any device.
Modify this circuit Add parts, take them out, or put one in series with another, then hear what it does. Tap to open.
Pick what to do, then tap the schematic. Your changes show in purple. Any change can go on a switch beside the knobs, from the menu in its row under Your changes.
Tap where each leg goes. Tap both ends of a part to put the new one across that part.
With Remove a part on, tap any part of the pedal or amp to take it out, and tap it again to put it back. Tapping a purple part you added deletes it.
Turn on Add in series with a leg and tap a part. In that part’s box, below the schematic, pick which leg to lift and what goes in the gap, such as a resistor between a cap and ground or a stopper in front of a grid.
With Cut into a wire on, tap any wire. Pick a part from the menu and it goes in the gap, wired in. Volume pot puts a pot there with the input on one end, the output on the wiper and the other end to ground.
With Run a wire on, tap a leg, then where the wire goes. Drag any piece of a wire you ran, or of an added part’s lead, to square it up or move it.
Your changes stay in this browser, on this device, for your next visit. Nothing is sent to us. Anyone using this browser can see them. They’re lost if you clear your browsing data or use a private window, so save a file to keep a copy. A shared link carries the circuit after the #, a part browsers never send to a server.
Input
pickup, unloadedat the pedal input
Output
at the amp input
Probe
Spectrum
Frequency response
What the curves mean
The black curve (white in dark mode) is the response to a very quiet signal, from the generator to the probe. The blue curve is measured with pink noise at the level you set, like an audio analyzer. When stages clip, the blue curve pulls away from the black one and the gray coherence line (right-hand scale) drops below 1. When that happens the response depends on how loud the signal is, and neither curve describes it by itself. Both use the signal generator, whichever Input tab is picked.
Output
Bias
every voltage and current at rest
What to listen for IC1b lifts the treble about 15 dB, and the NE570 compressor (IC2) halves the level changes, in decibels, before the delay chips. After each chip a low-pass and an NE570 expander undo the compressor, and the mixers cut the treble back down, so the chips’ hiss comes down with it. Each line has its own MN3102 clock. A transistor charges a 100 pF cap at a steady current until the ramp reaches a switching level, and the triangle moves that level. At rest line A delays about 2.2 ms and line B about 2.6 ms. In Mode 1 line A swings from about 1.4 to 3.0 ms while line B swings the other way, about 0.3 times a second. Each mixer adds the dry signal, its own line and some of the other mixer’s output above about 270 Hz. With SW1 closed, line B also goes into mixer A. The two copies’ pitch moves in opposite directions, so in the mix the pitch changes partly cancel. The four Mode buttons change two resistors on the button board. Mode 2 shorts R38 for more depth. Modes 3 and 4 make the sweep faster, about 0.6 and 0.85 times a second. The footswitch and its electronic bypass are left out.
Download.
Parts and what they do
Stock values. Tap a part on the schematic to change it.
- C1, 100 µF electrolytic
- Bulk cap across the 9 V supply.
- R4, 10 kΩ
- Top of the 4.5 V bias divider.
- R3, 10 kΩ
- Bottom of the 4.5 V bias divider.
- C3, 47 µF electrolytic
- Filters the 4.5 V line. The input stages, the compressor’s DC point and the output mixers work around it.
- IC10, 7 V
- A 78L06 regulator with the diode D8 in its ground lead, so its output sits near 6.6 V (the drawing marks it +7). Modeled as a steady 6.6 V source. It feeds the delay chips, their clocks, the LFO and the four op-amps that drive the clocks.
- R30, 100 Ω
- Feeds line A’s delay chip and its bias trimmer from the 6.6 V line.
- C38, 10 µF electrolytic
- Filters line A’s chip supply.
- R31, 100 Ω
- Feeds line B’s delay chip and its bias trimmer from the 6.6 V line.
- C28, 10 µF electrolytic
- Filters line B’s chip supply.
- R53, 100 Ω
- Feeds clock A (IC6 and Q8) from the 6.6 V line.
- C34, 10 µF electrolytic
- Filters clock A’s supply.
- R52, 100 Ω
- Feeds clock B (IC5 and Q7) from the 6.6 V line.
- C33, 10 µF electrolytic
- Filters clock B’s supply.
- R59, 10 kΩ
- Top of the 3.3 V divider for the LFO and the clock drivers.
- R60, 10 kΩ
- Bottom of the 3.3 V divider.
- C36, 47 µF electrolytic
- Filters the 3.3 V line.
- R6, 10 kΩ
- In series with the input.
- C4, 47 nF
- Input coupling cap.
- R5, 1 MΩ
- Biases the buffer’s input at 4.5 V and sets the input impedance near 1 MΩ.
- IC1a, RC4558
- Input buffer, a follower with a gain of 1. Half an M5218L.
- R7, 47 kΩ
- Input resistor of the pre-emphasis stage. Against the feedback it sets a gain of about 0.53 for low notes.
- C5, 4.7 nF
- With R8 beside R7 it lifts the treble. The gain starts rising near 600 Hz and levels off near 3.4 kHz, about 15 dB up.
- R8, 10 kΩ
- In series with C5. It sets where the treble lift levels off.
- R10, 33 kΩ
- Feedback resistor of the pre-emphasis stage.
- C8, 100 pF
- Rolls the top end off above about 64 kHz.
- R9, 100 kΩ
- A second feedback resistor, beside R10. C7 keeps it out at DC.
- C7, 1 µF electrolytic
- In series with R9.
- IC1b, RC4558
- Pre-emphasis stage, inverting. Treble goes up about 15 dB here, and the output mixers cut it back down, so the delay chips’ hiss comes down with it. The compressor and both dry paths start here. Half an M5218L.
- C9, 10 µF electrolytic
- Couples the signal into the compressor’s input, pin 6.
- IC2, NE570 (one half)
- NE570 half wired as a compressor. The input goes in at pin 6, and the gain cell and rectifier are fed from the output through C15. Every 2 dB change at the input is about 1 dB at the output, so quiet playing goes into the delay chips louder. Pins 9 to 16 are not used.
- C10, 470 nF electrolytic
- The compressor’s rectifier cap. With the chip’s 10 kΩ it sets how fast the gain follows the playing, about 5 ms.
- C15, 10 µF electrolytic
- Feeds the compressor’s output back to its rectifier and gain cell, pins 2 and 3.
- R15, 10 kΩ
- DC feedback from the compressor’s output, with R14. It sets the output’s DC level.
- R14, 10 kΩ
- DC feedback into the compressor’s summing node, pin 5.
- C14, 10 µF electrolytic
- Grounds the middle of R14 and R15 for the signal, so they set only the DC.
- D4, D5, 2.7 V zener pair, one direction, one each way
- Two 3 V zeners back to back (RD3.0EB1). With C16 they limit sudden jumps at the compressor’s output, before its gain has caught up. Modeled as the bench’s 2.7 V zener pair.
- C16, 1 nF
- In series with the zeners, so they act on fast changes only.
- C17, 1 µF electrolytic
- Couples the compressed signal into the low-pass ahead of the delay chips.
- R16, 100 kΩ
- Holds the filter at 4.5 V.
- R25, 10 kΩ
- First resistor of the low-pass ahead of the delay chips.
- C22, 470 pF
- First cap of the low-pass.
- R26, 10 kΩ
- Low-pass filter resistor.
- C20, 1.8 nF
- Feedback cap from Q5’s emitter. It squares up the low-pass’s knee.
- R27, 10 kΩ
- Low-pass filter resistor.
- C21, 220 pF
- Last cap of the low-pass. With C22, C20 and the three 10 kΩ it makes a three-pole low-pass near 20 kHz, so the clocks don’t fold high notes back down.
- Q5, BC549C
- Emitter follower of the low-pass. It feeds both delay lines. A BC549.
- R28, 10 kΩ
- Q5’s emitter load.
- R62, 10 kΩ
- Into Q9’s base.
- Q9, BC549C
- Emitter follower that drives line A’s delay chip. A BC549.
- R63, 10 kΩ
- Q9’s emitter load.
- C39, 1 µF electrolytic
- Couples the signal into line A’s delay chip.
- R61, 100 kΩ
- Brings the bias from RT-2 to the chip’s input.
- RT-2, 100 kΩ pot, linear taper
- BIAS-A trimmer, 100 kΩ. It sets the DC on line A’s chip input. Set at half, 3.3 V, as a factory-trimmed unit.
- IC9, MN3207
- MN3207 delay line A, 1024 stages. It holds 512 samples and passes each on after 512 clock periods, about 2.4 ms here. The two outputs are drawn as one pin. Swing set to 1.2 V for the 6.6 V supply.
- R68, 56 kΩ
- Load on line A’s chip outputs.
- C42, 22 nF
- Couples line A’s delayed signal into its low-pass.
- R67, 680 kΩ
- Top of a divider that holds the filter at 4.5 V.
- R69, 680 kΩ
- Bottom of that divider.
- R66, 10 kΩ
- First resistor of line A’s low-pass after the chip.
- C43, 470 pF
- First cap of the low-pass.
- R65, 10 kΩ
- Low-pass filter resistor.
- C44, 1.8 nF
- Feedback cap from Q10’s emitter.
- R64, 10 kΩ
- Low-pass filter resistor.
- C45, 220 pF
- Last cap of the low-pass, the same as the one ahead of the chips. It smooths the chip’s steps.
- Q10, BC549C
- Emitter follower of line A’s low-pass (TP1). A BC549.
- R70, 10 kΩ
- Q10’s emitter load.
- R29, 10 kΩ
- Into Q6’s base.
- Q6, BC549C
- Emitter follower that drives line B’s delay chip. A BC549.
- R23, 10 kΩ
- Q6’s emitter load.
- C27, 1 µF electrolytic
- Couples the signal into line B’s delay chip.
- R32, 100 kΩ
- Brings the bias from RT-1 to the chip’s input.
- RT-1, 100 kΩ pot, linear taper
- BIAS-B trimmer, 100 kΩ. It sets the DC on line B’s chip input. Set at half, 3.3 V.
- IC3, MN3207
- MN3207 delay line B, 1024 stages, about 2.8 ms here. The two outputs are drawn as one pin.
- R22, 56 kΩ
- Load on line B’s chip outputs.
- C26, 22 nF
- Couples line B’s delayed signal into its low-pass.
- R20, 680 kΩ
- Top of a divider that holds the filter at 4.5 V.
- R21, 680 kΩ
- Bottom of that divider.
- R19, 10 kΩ
- First resistor of line B’s low-pass after the chip.
- C25, 470 pF
- First cap of the low-pass.
- R18, 10 kΩ
- Low-pass filter resistor.
- C24, 1.8 nF
- Feedback cap from Q4’s emitter.
- R17, 10 kΩ
- Low-pass filter resistor.
- C23, 220 pF
- Last cap of the low-pass.
- Q4, BC549C
- Emitter follower of line B’s low-pass (TP2). A BC549.
- R24, 10 kΩ
- Q4’s emitter load.
- C46, 10 µF electrolytic
- Couples line A into its expander, pins 14 and 15.
- IC11 (9 to 16), NE570 (one half)
- NE570 half wired as line A’s expander. The rectifier and gain cell take the delayed signal, and pins 10 and 11 are joined. Every 1 dB at its input is about 2 dB at its output, which undoes the compressor and pushes the delay chip’s hiss down when the playing is quiet. Pin 12 is open.
- C48, 470 nF electrolytic
- Line A expander’s rectifier cap, the same as the compressor’s.
- C19, 10 µF electrolytic
- Couples line B into its expander, pins 2 and 3.
- IC11 (1 to 8), NE570 (one half)
- NE570 half wired as line B’s expander, the same as line A’s. Pins 6 and 7 are joined, and pin 5 is open.
- C47, 470 nF electrolytic
- Line B expander’s rectifier cap.
- R12, 68 kΩ
- With C11 a low-pass on the dry signal, near 100 Hz. It sends only the lows of the dry signal through Q2.
- C11, 22 nF
- Low-pass cap on the dry signal.
- R11, 2.2 kΩ
- In series with Q2’s base.
- Q2, BC549C
- Emitter follower for the low-passed dry signal. A BC549.
- R13, 10 kΩ
- Q2’s emitter load.
- C6, 1 µF electrolytic
- Couples the low-passed dry signal toward both mixers.
- R89, 1 MΩ
- Holds the low-passed dry line at 4.5 V.
- R71, 33 kΩ
- Dry signal into mixer A, straight from the pre-emphasis stage.
- R87, 220 kΩ
- Low-passed dry signal into mixer A.
- C59, 18 nF
- Couples line A’s expander into mixer A.
- R82, 47 kΩ
- Line A’s wet signal into mixer A.
- C62, 18 nF
- Couples line B’s expander into mixer A while SW1 is closed.
- R86, 39 kΩ
- Line B’s wet signal into mixer A while SW1 is closed.
- R75, 47 kΩ
- Feedback resistor of mixer A. Against R71 the dry signal comes through at a gain of about 1.4 for low notes.
- C50, 47 pF
- Rolls the top end off above about 70 kHz.
- C51, 4.7 nF
- With R74 beside R75 it cuts the treble back down, the de-emphasis that undoes IC1b’s lift.
- R74, 10 kΩ
- In series with C51.
- C55, 3.3 nF
- Brings some of output B into mixer A.
- R80, 180 kΩ
- Part of the path from output B into mixer A.
- C56, 1.2 nF
- With R84 beside R80 it lets more of output B’s treble across.
- R84, 33 kΩ
- In series with C56.
- IC12a, RC4558
- Mixer A, inverting. It adds the dry signal, the wet signals and some of output B, and cuts the treble back down. Half an M5218L.
- C49, 1 µF electrolytic
- Output A coupling cap.
- R73, 100 kΩ
- Holds output A at 0 V so the jack doesn’t pop.
- R72, 1 kΩ
- In series with output A.
- R92, 33 kΩ
- Dry signal into mixer B, straight from the pre-emphasis stage.
- R88, 220 kΩ
- Low-passed dry signal into mixer B.
- C60, 18 nF
- Couples line B’s expander into mixer B.
- R85, 47 kΩ
- Line B’s wet signal into mixer B.
- R76, 47 kΩ
- Feedback resistor of mixer B.
- C53, 47 pF
- Rolls the top end off above about 70 kHz.
- C52, 4.7 nF
- With R77 beside R76 it cuts the treble back down.
- R77, 10 kΩ
- In series with C52.
- C58, 3.3 nF
- Brings some of output A into mixer B.
- R81, 180 kΩ
- Part of the path from output A into mixer B.
- C57, 1.2 nF
- With R83 beside R81 it lets more of output A’s treble across.
- R83, 33 kΩ
- In series with C57.
- IC12b, RC4558
- Mixer B, the same as mixer A with lines A and B swapped. Half an M5218L.
- C54, 1 µF electrolytic
- Output B coupling cap.
- R78, 100 kΩ
- Holds output B at 0 V.
- R79, 1 kΩ
- In series with output B. Nothing is plugged into output B on the bench.
- IC7a, RC4558
- Comparator with hysteresis, which means it switches at one level on the way up and a different one on the way down. Its output flips to the other rail each time the triangle reaches a peak, so it puts out a square wave. A BA718, modeled with 4558-class values, on the 6.6 V line.
- R33, 33 kΩ
- From the triangle to the comparator. Against R35 it sets the triangle’s height at a third of the square’s.
- R35, 100 kΩ
- Positive feedback that holds the comparator where it last flipped.
- R34, 100 kΩ
- Holds the comparator’s − input at 3.3 V.
- C37, 10 nF
- From the square to the − input. It slows each flip slightly.
- R36, 330 kΩ
- In series with R37 on the button board. With R37 it sets the slowest sweep, about 0.3 times a second in Modes 1 and 2.
- R37, 180 kΩ
- Integrator input resistor. It sets the fastest sweep.
- C29, 10 µF electrolytic
- Integrator cap, one of two 10 µF in series, back to back, so together they act as one 5 µF cap that works either way round.
- C30, 10 µF electrolytic
- The second integrator cap.
- IC7b, RC4558
- Integrator. The square wave in makes a triangle out. A BA718, on the 6.6 V line.
- R38, 22 kΩ
- In series with R39 on the button board. With R39 it sets how much of the triangle reaches the clocks. Mode 2 shorts it for more depth.
- R39, 33 kΩ
- Input resistor of IC5a.
- R45, 47 kΩ
- Feedback resistor of IC5a. Its gain is 47 k over R39 plus Depth, 0.85 to 1.4.
- IC5a, RC4558
- Inverting amp. It inverts the triangle around 3.3 V and sets its size. Its output steers clock B, and IC6b. A BA718, on the 6.6 V line.
- R48, 47 kΩ
- Input resistor of IC6b.
- R51, 47 kΩ
- Feedback resistor of IC6b, equal to R48, so its gain is 1.
- IC6b, RC4558
- Inverting amp with a gain of 1. It inverts IC5a’s output again, so clock A swings the opposite way from clock B. A BA718, on the 6.6 V line.
- R54, 5.6 kΩ
- Top of the divider that sets clock A’s switching level.
- R49, 4.7 kΩ
- Bottom of that divider. With R54 it passes 0.46 of IC6b’s output, about 1.5 V at rest.
- R50, 100 kΩ
- Hysteresis for IC6a. On the drawing it goes to IC6a’s output, which is high for all but a moment of each cycle, so here it goes to clock A’s supply. It lifts the switching level about 0.16 V.
- R56, 1.5 kΩ
- Top of Q8’s base divider.
- R58, 10 kΩ
- Bottom of Q8’s base divider. It holds the base about 0.86 V under the clock supply.
- R55, 8.2 kΩ
- Q8’s emitter resistor. The 0.3 V or so across it sets a steady current, about 34 µA, that charges C35.
- Q8, 2N5087
- Current source for clock A. A BC559, modeled as a 2N5087, a low-noise PNP of the same kind.
- IC6a, IC8, LM311 ramp (stand-in)
- Clock A. Q8’s current charges C35, 100 pF, until the ramp reaches the level on IC6a’s + input. Then IC6a flips, the MN3102 (IC8) empties C35 through D7, and the ramp starts again. The MN3102 makes two clock phases at half that rate. A higher level makes a longer ramp, a slower clock and a longer delay. IC6a, D7, R57 and C35 are inside this part.
- R47, 4.7 kΩ
- Top of the divider that sets clock B’s switching level.
- R44, 4.7 kΩ
- Bottom of that divider. With R47 it passes half of IC5a’s output, about 1.65 V at rest.
- R46, 100 kΩ
- Hysteresis for IC5b. On the drawing it goes to IC5b’s output, which is high for all but a moment of each cycle, so here it goes to clock B’s supply.
- R41, 1.5 kΩ
- Top of Q7’s base divider.
- R40, 10 kΩ
- Bottom of Q7’s base divider.
- R42, 8.2 kΩ
- Q7’s emitter resistor. It sets the current that charges C32.
- Q7, 2N5087
- Current source for clock B. A BC559, modeled as a 2N5087.
- IC5b, IC4, LM311 ramp (stand-in)
- Clock B, the same as clock A: Q7 charges C32, 100 pF, IC5b compares the ramp with its + input, and the MN3102 (IC4) empties C32 through D6. IC5b, D6, R43 and C32 are inside this part.
About this version
- As drawn
- Negative ground, 9 V. A 78L06 regulator with a diode under it makes the 6.6 V line for the delay chips, the clocks and the LFO. The audio works around the 4.5 V from R3 and R4.
© 2026 Swell Amplification LLC. All rights reserved. The simulator, its circuit models, drawings, presets and text are the property of Swell Amplification LLC and may not be copied, reproduced, redistributed or used to build another product without written permission. The original circuits are historical designs documented in public sources, and no claim is made to them. Everything here is provided as is, without warranty of any kind, for study and personal use. Results are simulations of typical parts, not measurements of any real unit. Don’t rely on them for the safety of any build or repair. Tube amplifiers carry lethal voltages.
Product and company names are trademarks of their owners. They are used here only to identify the circuits these models are based on; this site is not affiliated with or endorsed by any of them.
From Swell Amplification, swellamps.com.